This paper reviews the energy yield enhancement characteristics of bifacial photovoltaic systems combined with solar tracking, focusing on their performance relative to conventional monofacial fixed-tilt configurations. The fundamental mechanisms of yield improvement are summarized, highlighting the largely additive contributions of solar tracking, which increases front-side irradiance, and bifacial modules, which utilize rear-side reflected and diffuse radiation. Reported results from previous studies indicate that bifacial systems with single-axis tracking typically achieve 25–35% higher annual energy yield compared with standard monofacial fixed-tilt systems, with variations depending on environmental and design conditions. Key design and environmental considerations influencing system performance are discussed to provide practical insights for the application of bifacial tracking systems in utilityscale photovoltaic installations.

This review offers a critical overview of recent developments in lead-free piezoelectric materials and flexible device architectures for self-powered wearable and Internet of Things systems. It examines the scientific and technological rationale for replacing conventional battery-dependent power sources with ambient mechanical energy harvesters, and it evaluates the relative merits of inorganic ceramics, organic polymers, and composite systems in achieving efficient electromechanical conversion under practical operating conditions. The discussion further considers compositional tuning, phase boundary engineering, microstructural optimization, and device-level integration as key strategies for improving piezoelectric output, mechanical compliance, durability, and manufacturability. By connecting fundamental materials design with application-driven device requirements, the review identifies the principal challenges and emerging directions necessary for the realization of reliable, scalable, and sustainable electronic platforms.

Quantum dots (QDs) are semiconductor nanocrystals with sizes on the order of several nanometers, whose bandgaps can be tuned by controlling the particle size. Owing to this bandgap tunability, QDs can absorb near-infrared (NIR) and short-wave infrared (SWIR) light, spectral regions that are difficult to access with conventional silicon-based devices. However, colloidal QDbased infrared photodetectors still suffer from intrinsically high dark current, trap-induced noise, and limited response speed. As a result, they exhibit fundamental performance gaps in terms of detectivity and speed–bandwidth product compared to epitaxial infrared detectors, highlighting the need for structural and architectural design strategies to overcome these limitations. In this review, we discuss recent advances in enhancing the spectral selectivity and sensitivity of infrared photodetectors through three-dimensional optical architectures, including metasurfaces and metamaterials. We focus in particular on design strategies and the underlying mechanisms responsible for performance enhancement, and we outline how structural approaches can be leveraged to effectively control the sensitivity and wavelength selectivity of QD-based infrared detectors.

Wearable temperature sensors are becoming increasingly important for continuous health monitoring, personalized healthcare, and biointegrated electronic systems. However, conventional temperature-sensing platforms often suffer from limited thermal sensitivity, insufficient mechanical compliance, and unstable performance under repeated deformation, making it difficult to detect subtle physiological temperature variations in real time. Here, this tutorial status report presents a fabrication strategy for highly sensitive wearable temperature sensors based on gold-doped crystalline silicon nanomembranes. Gold diffusion into crystalline silicon introduces deep-level impurity states that modulate the Fermi level and shift the freeze-out region toward the physiological temperature range, enabling an ultrahigh negative temperature coefficient of resistance. By integrating the gold-doped silicon nanomembrane with a polyimide-supported ultrathin platform, neutral mechanical plane design, and serpentine mesh interconnects, the resulting device can provide high thermal sensitivity, fast response, conformal skin attachment, and stable operation under mechanical deformation. This fabrication approach is expected to broaden the use of impurity-engineered silicon nanomembranes in next-generation wearable sensors, flexible bioelectronics, and multifunctional healthcare monitoring systems.

The direct utilization of steelmaking by-product gases in solid oxide fuel cells (SOFCs) offers a promising pathway to improve energy efficiency and reduce carbon emissions in the steel industry. In this study, a Sr-deficient and Ni-doped double perovskite oxide, Sr_1.95Fe_1.35Ni_0.15Mo_0.5O_6-δ (SFNM), was investigated as an anode material for direct Linz-Donawitz converter gas (LDG)-fueled SOFCs. A single-phase double perovskite structure was successfully obtained after calcination at 1,200°C for 12 h, while exsolved metallic Ni nanoparticles were generated on the SFNM surface after reduction at 800°C. Electrochemical performance was evaluated using H₂, simulated-LDG, and CO/CO₂ (85:15) fuels at 800°C. The maximum power densities achieved were 1.23, 0.70, and 0.40 W cm^-2 for H₂, simulated-LDG, and CO/CO₂ fuels, respectively. Although CO-containing fuels exhibited lower opencircuit voltages and power outputs than H₂, the SFNM anode maintained stable operation and appreciable performance under direct simulated-LDG utilization. Impedance analysis revealed that the increased polarization resistance in simulated-LDG and CO/CO₂ atmospheres was mainly associated with fuel adsorption/desorption and gas diffusion, while interfacial charge-transfer resistance remained relatively small. The superior performance obtained with simulated-LDG compared to the CO/CO₂ mixture was attributed to the presence of a small amount of H₂, which facilitated anode reaction kinetics. These results demonstrate that SFNM is a promising mixed ionic-electronic conductor anode for the direct electrochemical conversion of CO-rich steelmaking by-product gases into electricity.

The dielectric and piezoelectric properties of the ferroelectric BaTiO₃ were measured and analyzed using both strong and weak electric field conditions. To measure the electric field induced polarizations and strains, a high voltage source and the measuring circuit were used and the dielectric constants were measured with an impedance analyzer. The spontaneous polarization of BaTiO₃ at room temperature was calculated as 17 μC/cm² based on the lattice structure and internal ion location, which is in good agreement with the experimental results. The polarization and strain hysteresis curve according to the electric field were analyzed in terms of lattice structure and ion position. The magnitude of remanent polarization is proportional to the offset distance of Ti⁴⁺ ion from the lattice center. The magnitude of dielectric permittivity is proportional to the degree to which Ti⁴⁺ ion can move freely inside the lattice. The magnitude of piezoelectric constant d₃₃ is proportional to how much Ti⁴⁺ ion distorts the lattice as it moves inside the lattice.

Dye adsorption is one of the most time-consuming processes in the fabrication of dye-sensitized solar cells (DSSCs), typically requiring approximately 24 h at room temperature. In this study, the effect of adsorption temperature and time on photovoltaic performance of DSSCs was investigated in order to reduce processing time and improve device productivity. Nanoporous TiO₂ photoelectrodes were immersed in N719 dye solution at 60°C for 3 h, 10 h, 17 h, and 24 h, and their performance was compared with that of cells sensitized at room temperature for 24 h. Photovoltaic characterization under AM 1.5 illumination showed that DSSCs sensitized at 60°C exhibited improved performance compared to those sensitized at room temperature. The device sensitized at 60°C for 3 h showed comparable or higher conversion efficiency than the reference cell sensitized for 24 h at room temperature. The improvement in device performance is attributed to enhanced dye adsorption kinetics resulting from increased reaction rate between the carboxyl groups of N719 dye molecules and hydroxyl groups on the TiO₂ surface. Electrochemical impedance spectroscopy analysis revealed reduced recombination resistance at the TiO₂/dye/electrolyte interface for cells sensitized at elevated temperature. UV–Vis absorption analysis confirmed increased dye loading on the TiO₂ surface for the 60°C condition. These results demonstrate that elevated temperature dye adsorption significantly reduces processing time while maintaining photovoltaic performance, providing an effective strategy for improving manufacturing efficiency of DSSCs.

Dye-sensitized solar cells (DSSCs) suffer from efficiency limitations due to interfacial charge recombination at the TiO₂/dye/electrolyte interface. In this study, aminopropyltrimethoxysilane (APS) was introduced onto nanoporous TiO₂ photoelectrodes via a dip-coating process with controlled coating times to investigate the effect of silanization time on interfacial charge transport behavior. Unlike concentration-driven structural modification, this work focuses on the evolution of the APS-modified interface governed by reaction time. The DSSC with 30 min APS treatment exhibited the highest power conversion efficiency of 5.34%, representing a 19% enhancement compared to the untreated device (4.49%), mainly due to increased short-circuit current density and open-circuit voltage. However, prolonged coating times (2 h and 24 h) resulted in a significant decrease in photocurrent density, leading to reduced device performance despite partial improvement in recombination resistance. These results are attributed to the time-dependent evolution of the APS interfacial layer. At moderate coating time, APS provides effective surface functionalization, enhancing dye adsorption and suppressing interfacial recombination. In contrast, prolonged coating is expected to induce increased surface coverage and silane condensation, which can hinder electron injection and increase charge transport resistance. Therefore, the photovoltaic performance is governed by a trade-off between recombination suppression and charge injection efficiency, controlled by the silanization time. This study highlights the critical role of interfacial reaction kinetics in determining charge transport behavior and provides an effective strategy for optimizing DSSC performance through time-dependent interface engineering.

We have studied the thermal stability of NCM622 cathode material for Li-ion batteries using real-time synchrotron x-ray scattering below 600°C in both air and vacuum. The expansion of the mean particle size, which reached maximum values of 10.3 μm in air and 10.6 μm in vacuum at 200°C, was attributed to the dehydration of intergranular water within the NCM622 powders. Across all annealing temperatures, the amount of crystal NCM622 phase in air was consistently higher than that in vacuum. The crystal domain sizes in air showed less variation than that in vacuum during annealing from RT to 500°C. These indicate that the crystal NCM622 phase is more thermally stable during annealing in air than in vacuum. This stability is attributed to the presence of 21% oxygen in air, which is absent under vacuum conditions.

Organic solar cells based on bulk heterojunction (BHJ) structures have attracted considerable attention because of their low fabrication cost, mechanical flexibility, and compatibility with solution-processing techniques. In BHJ organic photovoltaic devices, nanoscale morphology and crystallinity of the photoactive layer critically influence photovoltaic performance. In this study, the effects of solvent selection and thermal annealing on crystallization evolution and photovoltaic characteristics of P3HT:PCBM organic solar cells were systematically investigated. Three different solvents, including toluene, chlorobenzene (CB), and dichlorobenzene (DCB), were employed for active-layer fabrication, followed by post-thermal annealing treatment. UV–visible absorption spectroscopy revealed solvent-dependent differences in molecular ordering and intermolecular π–π interactions within the active layer. X-ray diffraction analysis confirmed that thermal annealing significantly enhanced crystallinity and lamellar ordering of P3HT domains, particularly for CB-processed films. Electrical characterization demonstrated that solvent evaporation behavior strongly affects photovoltaic performance. Among the investigated devices, the thermally annealed CB-processed device exhibited the highest power conversion efficiency of 1.83% with an enhanced short-circuit current density of 7.057 mA cm⁻². The improved device performance is attributed to optimized crystallization behavior and balanced nanoscale phase separation induced by the moderate evaporation characteristics of CB. In contrast, although DCB-assisted films exhibited relatively strong optical absorption and enhanced crystallinity, excessively slow solvent evaporation likely induced excessive aggregation and coarse phase separation, limiting efficient photovoltaic characteristics. These results demonstrate that solvent engineering combined with thermal annealing is an effective strategy for controlling morphology evolution and crystallization behavior in P3HT:PCBM bulk heterojunction solar cells.

This study proposes an optimization strategy for the over-current protection (OCP) parameters of a lithium iron phosphate (LiFePO₄, LFP) battery system used in electric golf carts operating under high motor-load conditions. Real-world hillclimbing tests were conducted under four clearly defined payload/passenger conditions to analyze the transient discharge-current pro-file, voltage sag, and cell-temperature response. The maximum discharge current reached -238.2 A under the 200 kg cargopayload and one-passenger condition, and the current interval exceeding 150 A lasted up to 27 s. The maximum instantaneous power was 11.05 kW. Thermal analysis showed that the cell-temperature rise was within 2°C and the maximum measured cell temperature was 22.3°C. Linear regression of voltage and current yielded R² = 0.9368 and dV/dI = 0.0126 Ω, which was used as the DC internalresistance estimate. Based on these quantitative results and the cell specification limit of 300 A continuous discharge, the OCP threshold was reviewed from 250 A to 280 A to improve driving continuity while remaining below the allowable continuous-discharge current. EIS-based SOH estimation and the AI-BMS variable protection logic are presented as an extension framework for reflecting temperature and aging effects in future OCP-setting decisions.

With the rapid expansion of electric vehicles (EVs) and energy storage systems (ESS), ensuring the operational safety of lithium-ion batteries has become a critical technical challenge. Conventional battery management systems (BMS) primarily rely on threshold-based rule logic, which is limited in detecting coupled anomalies and early-stage degradation patterns. In this study, a deep learning-based framework for multivariate anomaly detection is proposed using BMS sensor data, including voltage, current, temperature, state of charge (SOC), and state of health (SOH). Five representative fault scenarios were defined, including thermal runaway precursors, cell voltage imbalance, SOC inconsistency, internal resistance increase, and communication delay. The proposed CNN-LSTM model was compared with conventional Rule-based methods and machine learning models, including Isolation Forest, Autoencoder, and LSTM. Experimental results show that the proposed model achieved the highest performance, with an F1-score of 0.885, an AUC of 0.94, and a detection delay of 8.1 s. In contrast, the Rule-based method exhibited a significantly higher false negative rate of 42.0%, indicating limitations in detecting complex anomaly patterns. These results demonstrate that the proposed spatiotemporal deep learning approach can significantly improve the accuracy and responsiveness of battery anomaly detection. Furthermore, the proposed method is expected to contribute to enhancing safety, reliability, and predictive diagnostics in next-generation intelligent BMS platforms.

The development of a large-area solution process for CuO nanowires, which are promising p-type thin film transistors (TFT) channel materials, is required. To overcome the limitations of the existing high-vacuum and high-cost deposition process, a large-area Cu nanowire network was formed on the substrate using the Mayer rod coating method, and a CuO channel was implemented by subsequent thermal annealing. Consequently, p-type TFT with an on/off current ratio of 1.4×10⁴ and a field-effect mobility µ_FE≈10^-4 cm²/(V⋅s). was fabricated and optimized. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses showed that the sample annealed at 200°C exhibited an incomplete oxidation state with a mixed Cu/Cu₂O phase and a high fraction of M-OH species (58.78%), resulting in a low on/off current ratio (≈1.2). In contrast, annealing at 450°C leads to a CuOdominant phase, where the fraction of lattice oxygen(O1) increases to 31.11% and the oxygen vacancy (VO) component increases to 7.15%, indicating a significant improvement in hole concentration and charge transport. These phase transitions and surface chemical changes are identified as the key mechanisms for the enhanced TFT switching characteristics. The low-cost, large-area Mayer rodbased solution process proposed in this study provides a basic process platform for p-type TFTs applicable to flexible wearables and display technologies and suggests the possibility of commercialization through additional optimization of bias stability in the future.

Renewable energy harvesting technologies, which convert ambient resources such as wind into electrical energy, have attracted significant attention as sustainable power sources for self-powered systems. However, the long-term applicability of wind energy harvesters in remote or extreme environments has not yet been fully discussed, particularly in terms of structural robustness and environmental adaptability. In this study, we designed a double-clamped flutter-type triboelectric generator (DFTEG) for efficient wind energy harvesting and evaluated its output performance under various simulated outdoor conditions. The DFTEG features a modular acrylic frame with a magnet-based assembly for easy maintenance and film replacement, utilizing PTFE films and aluminum electrodes to maximize the charge density difference according to the triboelectric series. Structural optimization revealed that a single-film configuration with a length of 110 mm produced the most stable flutter vibration and a large effective contact area, achieving a maximum open-circuit voltage of 42.28 V and a short-circuit current of 2.89 μA. Furthermore, performance evaluations under various environmental variables, including relative humidity, temperature, and sand particles interference, confirmed consistent electrical output across diverse environmental conditions. These results demonstrate the potential of the proposed DFTEG as an environmentadaptive independent power source capable of stable operation under complex environmental factors.