Dye-sensitized solar cells (DSSCs) suffer from efficiency limitations due to interfacial charge recombination at the TiO₂/dye/electrolyte interface. In this study, aminopropyltrimethoxysilane (APS) was introduced onto nanoporous TiO₂ photoelectrodes via a dip-coating process with controlled coating times to investigate the effect of silanization time on interfacial charge transport behavior. Unlike concentration-driven structural modification, this work focuses on the evolution of the APS-modified interface governed by reaction time. The DSSC with 30 min APS treatment exhibited the highest power conversion efficiency of 5.34%, representing a 19% enhancement compared to the untreated device (4.49%), mainly due to increased short-circuit current density and open-circuit voltage. However, prolonged coating times (2 h and 24 h) resulted in a significant decrease in photocurrent density, leading to reduced device performance despite partial improvement in recombination resistance. These results are attributed to the time-dependent evolution of the APS interfacial layer. At moderate coating time, APS provides effective surface functionalization, enhancing dye adsorption and suppressing interfacial recombination. In contrast, prolonged coating is expected to induce increased surface coverage and silane condensation, which can hinder electron injection and increase charge transport resistance. Therefore, the photovoltaic performance is governed by a trade-off between recombination suppression and charge injection efficiency, controlled by the silanization time. This study highlights the critical role of interfacial reaction kinetics in determining charge transport behavior and provides an effective strategy for optimizing DSSC performance through time-dependent interface engineering.

Renewable energy harvesting technologies, which convert ambient resources such as wind into electrical energy, have attracted significant attention as sustainable power sources for self-powered systems. However, the long-term applicability of wind energy harvesters in remote or extreme environments has not yet been fully discussed, particularly in terms of structural robustness and environmental adaptability. In this study, we designed a double-clamped flutter-type triboelectric generator (DFTEG) for efficient wind energy harvesting and evaluated its output performance under various simulated outdoor conditions. The DFTEG features a modular acrylic frame with a magnet-based assembly for easy maintenance and film replacement, utilizing PTFE films and aluminum electrodes to maximize the charge density difference according to the triboelectric series. Structural optimization revealed that a single-film configuration with a length of 110 mm produced the most stable flutter vibration and a large effective contact area, achieving a maximum open-circuit voltage of 42.28 V and a short-circuit current of 2.89 μA. Furthermore, performance evaluations under various environmental variables, including relative humidity, temperature, and sand particles interference, confirmed consistent electrical output across diverse environmental conditions. These results demonstrate the potential of the proposed DFTEG as an environmentadaptive independent power source capable of stable operation under complex environmental factors.

This paper reviews the energy yield enhancement characteristics of bifacial photovoltaic systems combined with solar tracking, focusing on their performance relative to conventional monofacial fixed-tilt configurations. The fundamental mechanisms of yield improvement are summarized, highlighting the largely additive contributions of solar tracking, which increases front-side irradiance, and bifacial modules, which utilize rear-side reflected and diffuse radiation. Reported results from previous studies indicate that bifacial systems with single-axis tracking typically achieve 25–35% higher annual energy yield compared with standard monofacial fixed-tilt systems, with variations depending on environmental and design conditions. Key design and environmental considerations influencing system performance are discussed to provide practical insights for the application of bifacial tracking systems in utilityscale photovoltaic installations.

This paper proposes a circular sequential lighting control method to reduce current imbalance and luminance deviation among multiple LED modules in AC-powered LED lighting systems. Conventional fixed-sequence lighting control repeatedly prioritizes the same LED modules in every rectified voltage cycle, which leads to unequal current distribution, luminance non-uniformity, and the accelerated degradation of specific modules during long-term operation. To address these limitations, a circular sequential lighting strategy is introduced, in which the lighting order is cyclically rotated at every rectified cycle, ensuring that all LED modules experience equal lighting opportunities. A prototype AC-LED lighting system consisting of four series-connected LED modules was implemented and experimentally evaluated. The results demonstrate that, while the conventional fixed-sequence method produces a maximum average current deviation of up to 1.6 mA among modules, the proposed method equalizes the average current across all modules to approximately 17.1 mA. Furthermore, the flicker index remains at 0.13, which is comparable to that of the conventional method, indicating that luminance uniformity is improved without degradation of optical performance. The proposed circular sequential lighting control effectively distributes electrical stress, enhances luminance uniformity, and improves long-term reliability, making it a practical and efficient solution for high-quality AC-LED lighting applications.

Long lifetime, low power consumption, and environmental friendliness have enabled light-emitting diode (LED) lighting to rapidly replace conventional light sources such as incandescent and fluorescent lamps. In particular, AC-LED lighting systems can be directly powered by commercial alternating current (AC) sources; however, they suffer from significant luminance deviation caused by uneven current distribution among LED light-emitting modules. This paper proposes a lighting control method that improves flicker performance while maintaining lamp brightness and effectively reduces luminance deviation in AC-LED lighting. The proposed method reduces luminance deviation by controlling the lighting order of multiple LED light-emitting modules. Among four LED modules, only the required number of modules is continuously turned on, and the lighting priority alternates between rectification cycles. Specifically, during odd rectification cycles, LED modules are activated sequentially in ascending order (11→12→13→14), whereas during even rectification cycles, they are activated in descending order (14→13→12→11). By alternately applying continuous lighting control with opposite activation orders, the proposed reverse alternating lighting control method equalizes the current distribution among LED modules. As a result, luminance uniformity is improved, electrical stress concentration on specific modules is reduced, and the operational lifetime of the LED modules is extended compared with the conventional fixed-sequence lighting control method.

To ensure the long-term reliability of flexible photovoltaic (FPV) modules, it is crucial to develop an effective moisture barrier layer that prevents the infiltration of moisture and oxygen. We developed such a layer composed of parylene (700 nm) and AlOx (70 nm), optimizing its material properties, moisture-blocking performance, and processing conditions. The barrier layer applied to the Ethylene Tetrafluoroethylene (ETFE) substrate demonstrated a water vapor transmission rate (WVTR) of 6.33 × 10^-2 g/m²/day and an average visible light transmittance (AVT) of 85.3% over the 380-780 nm wavelength range. For the FPV module with this barrier, Damp/Heat (DH) reliability testing was conducted at 85℃ and 85% relative humidity for up to 1,000 hours. During testing, the power conversion efficiency (PCE) decreased slightly from 25.4% (0 hr) to 24.7% (1,000 hr), reflecting a minimal reduction of only 0.7%. The primary cause of degradation was identified as a -4% relative change in shortcircuit current density (JSC) before and after DH testing. Consequently, the ETFE/parylene/AlOx multilayer moisture barrier proved highly effective in ensuring the long-term reliability of solar modules.

This review examines the principles, limitations, and recent advancements in elastic modulus measurement using nanoindentation. The importance of accurate contact area prediction is discussed, along with the Oliver-Pharr method and its limitations. The Continuous Stiffness Measurement (CSM) technique is presented as a significant improvement, allowing continuous measurement of mechanical properties throughout the indentation process. For ultra-thin films, the Li and Vlassak method, which incorporates Yu's solution and the concept of effective thickness, is highlighted as a means to correct for substrate effects. Recent developments in artificial neural network-based models for elastic modulus prediction are also explored. These advancements have greatly expanded the applicability of nanoindentation in semiconductor and MEMS device reliability assessment.

We propose a real-time information propagation arithmetic neural network (PANN) that minimizes the loss of power generation output of the system in the event of sudden changes in the module due to strong external typhoons or earthquakes at the solar power generation facility site. In addition, we propose a new double-sided module reflector that can reduce the local loss of power generation efficiency of the single-sided module reflector that is currently widely distributed, as well as the environmental pollution and inconvenience of maintenance work of the existing double-sided module. We present a computational network that can detect the faulty solar panel in real-time by checking the fault status of the installed solar panel and using a real-time computation method through a node-to-node diffusion method. In particular, this method recognizes the power loss part due to sudden changes in the module in real time and can take emergency measures for various nonlinear field facilities through a neural structure that finds the optimal distance up, down, left, and right. To confirm the characteristics of the loss reduction control of the field facility, we confirmed that the system was configured as a 7-degree-of-freedom control model using the PANN neural network learning structure method and improved the power generation output. PANN (Propagation Arithmetic Neural Networks) and various module systems are proposed for the real-time recovery of faulty solar panels and improving module system efficiency.

One method to increase the output of solar modules is the application of the Half-cut technique, which requires a scribing process involving direct irradiation of infrared lasers on the solar cells. During this process, the laser melts the surface of the solar cells at high temperatures, enabling mechanical division, but this can lead to output loss due to thermal degradation caused by the laser. To minimize such losses, a low-temperature and low-loss division method has been devised. In this study, we compared the electrical characteristics and leakage currents affecting output degradation between the newly devised low temperature and low-loss cell division method and the conventional laser division method. Additionally, we conducted a 3-point flexural test to evaluate the mechanical properties of both methods.

Dielectric resonators with BT (BaTiO₃), TiO₂, and ZrO₂ powders without using the rare earth oxide powders were fabricated for the target relative permittivity of between 30 and 40 and the filter characteristics of metal cavity filter with the dielectric resonators inside were evaluated. Powder characteristics such as particle size distributions and specific surface areas were measured for the composing raw powders to evaluate the powder states. After measuring and comparing the relative permittivity and dielectric losses of the dielectrics of three different compositions, the specific composition was determined (BT:TiO₂:ZrO₂=1:4:1 in mole) and the dielectric resonators were fabricated with that composition, which shows relative permittivity of around 35. The powder characteristics of mixed powders with the determined composition were also evaluated to investigate any agglomerates possibly formed in the process of powder mixing. Dielectric resonators were fabricated by the powder compaction (compaction pressure: 31 MPa) and firing method. The peak firing temperature was 1,300℃ and the holding time at the peak temperature was 3 hours. After firing, cylindrical resonators with one end closed were mechanically machined to eliminate any size differences in dielectric resonator which can be caused by the shrinkage difference during each firing process of resonator fabrication. After measuring the resonator characteristic in the frequency range from 3.6 GHz to 3.8 GHz by changing the height of dielectric resonator, the height of the resonator was determined to be 11.7 mm. Finally, filter characteristics of TM (Transverse Magnetic) mode metal cavity filters with the dielectric inside were measured and evaluated. The metal cavity filters with the dielectric resonators showed the insertion losses of below 1 dB with the band widths of 200 MHz and over 20 dB return losses from 3.6 GHz to 3.8 GHz, whose filter characteristics well satisfied the requirements of the band pass filters for the base stations and it was proved that the dielectrics using the proposed composition could be used as dielectric resonator.

MBB (multi-busbar) technology is a module technology to achieve high power, and the use of a number of thin circular metal wires increases light-receiving capacity and reduces resistance. In the process of interconnection using a wire, the stress of the cell increases depending on the degree of coupling between the wire and the cell and the degree of damage caused by heat, or the mobility of current decreases due to poor bonding. The degree of such loss is affected by IR lamp, hot plate temperature and wire thickness. In addition, the values of contact resistance were compared and analyzed to analyze the cause of the decrease in electrical characteristics. In this study, process condition optimization was carried out through peeling test, SEM analysis, EL test, and pre/post bonding efficiency characteristic analysis of the bonded cell according to process conditions, compared the contact resistance.

The possibility of a dye-sensitized solar cell (DSSC) submodule was evaluated as an independent power source that can drive a smart liquid crystal window (SLW) that selectively blocks sunlight when electricity is applied. In order to save energy and increase the functionality of buildings, SLW operation was supplied directly from DSSC submodule, rather than connecting to the existing power system and external power sources. It was confirmed that the SLW can control light transmittance through self-generation using the DSSC submodule composed of 6 cells at low light of 2,500 lux. These results imply that there is a high possibility of combining smart windows and DSSCs suitable for window-type building-integrated photovoltaic (BIPV) systems. DSSCs, which can self-generate power in low light, are expected to increase their usability in urban BIPV systems through combination with smart window technology.

This work focuses on improving the light-harvesting efficiency of thin-film silicon solar cells through innovative multi-architecture surface modifications. To create a regular optical structure, a lithographic process was performed to form it on a glass substrate through various etching processes, from Etch-1 to Etch-3. AZO was deposited on top of the structures and re-etched to create a multi-architectural surface. These surface-modified structures improved the light absorption and overall performance of the solar cell through changes in optical and physical properties, which we will analyze. In addition, we investigated the effect of post-cleaning on the etched glass structures through EDX analysis to understand the mechanism of the etching action. The results of this study are expected to provide important guidelines for the design and fabrication of solar cells and other photovoltaic devices.

Currently, the most developed new energy source is solar energy. Because solar power is installed outside, it is exposed to many pollutants. Pollutants are causing the characteristics of solar energy to deteriorate. Therefore, this study aims to develop a water-repellent coating to prevent contamination of solar modules. Silica and Titania materials are mainly used as water-repellent coating materials. In this study, it was based on silica and the contact angle characteristics were measured according to the change in the amount of silica and ammonia water added and the number of coatings. As a result of the measurement, it was confirmed that the contact angle was more than 60 degrees when 0.5 mol of TEOS was added to 50 mL and 0.15 M when 1 mL of ammonia water was added to 296.47 ml of distilled water. And it was confirmed that the contact angle improved when the number of coatings was applied twice. A water-repellent coating material was applied to low iron tempered glass used to protect dye-sensitized solar cell modules. The characteristics of the module were measured after spraying DI-Water on low-emission tempered glass with a water-repellent coating. As a result of the measurement, the efficiency of the module without application, the efficiency of the module coated once, and the module coated twice were 4.87%, 4.90%, and 4.91%, respectively. It was confirmed that the efficiency of the module increased by applying water-repellent coating. As a result of this study, it is determined that the water-repellent coating material will help improve solar power generation efficiency and lifespan by being self-cleaning and non-reflective.

The energy demand in the world is expected to exceed 740 million TJ by 2040 and our dependence on fossil fuels needs to be switched to sustainable and renewable energy sources like solar energy. Building Integrated Photovoltaic (BIPV) is one of the best approaches to extracting solar energy. There are more than 200 BIPV products in the market currently but when it comes to integrating these products into the technical aspects such as buildings’ structural integrity, thermal, daylight retainment and aesthetic prospects to be considered. The share of BIPV integration potential of different building types in the world of residential, agricultural, industrial, commercial and other buildings account for 66%, 4.8%, 8.1%, 19.9%, and 1.2% accordingly. Many solar technologies developed to achieve architectural requirements, but the main problem is the trade-off between efficiency and aesthetic appeal, which is less than 10% in coloured and transparent solar modules. This paper discusses the different applications of solar photovoltaics (PV) in building architecture, technical requirements, and different module technologies. The article provides a comprehensive guide for researchers and designers working on the development of BIPV integrations.

In this paper, we analyzed the transformation of the power following by the angle of incidence of the solar, the angle of photovoltaic module and artificial solar changed from 30° to 90° and synchronously changed the distance from 0.1 m to 0.5 m. Setting the distance between the artificial solar and the luminometer from 0.1 m to 0.5 m and set the angles to 90°, 60°, 45°, and 30°, the angle was 90° and when the distance was 0.1 m, the maximum Illuminance was 19,580 lux, the light could be obtained more. If the angle of incidence between the Artificial solar and the photovoltaic module was 90° and the variable resistance was 1,000 Ω at a distance of 0.4 m, the maximum power reached 0.82 W. Provided that the angle of incidence between the artificial solar and the photovoltaic module was 90° and the distance was 0.2 m since the variable resistance had the maximum power of 500 Ω, the maximum power was 0.78 W. At 1,000 Ω, the maximum power is 0.80 W so the maximum power at the variable resistance 1,000 Ω could obtain higher power than the variable resistance 500 Ω. The variable resistance was 1,000 Ω and the angle of incidence between the Artificial solar and the photovoltaic module was 90° at a distance of 0.4 m, and the maximum power reached 0.82 W. The angle was 60° at 0.3 m and 0.4 m the maximum power reached 0.10 W. The angle was 45° at 0.2 m maximum power reached 0.020 W, the angle was 30° at 0.4 m, and the maximum power reached 0.004 W. In four results about maximum power depending on the angle of incidence between the artificial solar and the photovoltaic module, the luminous efficiency and maximum power can be got the best at an angle of 90°.

In order to spread LED lighting, LED lighting technology directly driven by alternating current (AC) commercial power has recently been introduced. Since current does not flow at a voltage lower than the threshold voltage of the LED, a nonconductive section occurs in the current waveform, and the higher the threshold voltage of the LED, the more discontinuous current waveforms are generated. In this paper, multi-LED modules are connected in series so that the threshold voltage can be adjusted according to the number of LED modules. A small number of LED modules are driven at a low instantaneous rectified voltage, and a large number of LED modules are driven at a high instantaneous rectified voltage to lengthen the overall lighting time of AC-LED lighting, thereby minimizing the luminance deviation of AC-LED lighting. In addition, the load current flowing through the LED module is adjusted to be the same as the design current even at the maximum rectified voltage higher than the design voltage, so that the light brightness of the LED module is kept constant. Therefore, even if the rectified voltage applied to the LED module changes, the AC-LED lighting in which the light brightness is constant and the luminance deviation is minimal has been realized.

Owing to carbon materials’ diverse functionalization and versatility, the design and synthesis of carbon-based three-dimensional porous structures have become important foundational research topics across various fields. Among the various methods for producing porous carbon structures, laser-induced graphene (LIG) has garnered attention because of its large surface area, controllable structure, excellent electrical conductivity, scalability, and eco-friendly synthesis process. In addition, recent research results have reported more novel functionalities by advancing further from the unique characteristics of LIG through functionalization or compounding of LIG, making it an attractive material for various applications in electronic devices, sensing, catalysis, and energy storage. This review aims to update the research trends in LIG and its functionalization, providing insights to inspire more interesting studies on functional LIG to expand its potential applications ultimately. Starting with the synthesis method and material characteristics of LIG, we introduce the functionalization of LIG, which is classified into surface modification, heteroatom doping, and hybridization based on the interaction mechanism. Finally, we summarize and discuss the prospects of LIG and its functionalization.

In the past, the efficiency of solar cells had been increased in order to increase the efficiency of solar modules. However, in recent years, in order to increase output in the solar industry and market, the competitiveness of solar cells based on large-area solar cells and multi-bus bar has been increasing. Multi-busbar solar module is a technology to reduce power loss by increasing the number and width of the front busbar of the solar cell and reducing the current value delivered by the busbar by half through half-cutting. In the case of the existing M2 (156.75×156.75 ㎟) solar cell, even with a half-cut, power loss could be sufficiently reduced, but as the area of the solar cell is enlarged to more than M6 (166×166 ㎟), the need for more divisions emerged. This affected not only solar cells but also inverters required for module array configuration. Therefore, in this study, the electrical characteristics of a large-area solar cell and after division were extracted using Griddler simulation. The output characteristics of the module were predicted by applying the solar cell parameters after division to PSPice, and a guideline for the large-area solar module design was presented according to the number of divisions of the large-area solar cell.

Calcium fluoride (CaF₂) single crystal is applied to numerous industrial applications, especially for optical uses. To have excellent optical transmission properties, however, CaF₂ crystals should be carefully fabricated through liquid-phase crystal growth techniques. In this study, as one of the early stage research activities to grow CaF₂ crystals with a good transmittance at the ultraviolet wavelength range, computational thermodynamic models were provided to deepen the understanding of the crystal growing processes of CaF₂ under various conditions. To remove point defects and oxygen impurities in the grown CaF₂ crystals, the system was thermodynamically evaluated to get optimal process conditions. From the reviews of previous experimental studies, computational thermodynamic approaches were found to be an effective and powerful tool to understand the meaning of the crystal growth processes and to obtain optimal process conditions.

Global warming is accelerating due to the use of fossil fuels that have been used continuously for centuries. Now, humankind recognizes its seriousness, and is conducting research on searching for eco-friendly and sustainable energy. In the field of solar energy, which is a kind of eco-friendly and sustainable, many studies are being conducted to enhance the output performance of the module. In this study, the output improvement for the shingled module structure was studied. In order to improve the output performance of the module, the thickness of the encapsulant was increased, and the lamination process conditions have been improved accordingly. After that, the crosslinking rate was analyzed, and the suitability of the lamination process conditions was judged using this. In addition, a peeling test was conducted to analyze the correlation between the adhesion of the encapsulant and the output performance of the module. Finally, the optimization for the encapsulant material and the lamination process conditions for high-power shingled modules was established, and accordingly, the market share of high-power shingled modules in the solar module market can be expected to rise.

Interest and investment in renewable energy have increased worldwide, highlighting the need for renewable energy. Solar energy was the most promising energy of all renewable energy sources, and it has the highest investment value. Because photovoltaics require a certain amount of area for installation, high density and high output performance are required. Shingled module is a promising technology in that they are featured by higher density and higher output compared to the conventional modules. Shingled technology uses a laser scribing to divide solar cells that are to be bonded with electrically conductive adhesive (ECA) to produce and connect strings, which has a higher output in the same area than the conventional modules. In the process of producing solar modules, metal ribbons are used to interconnect cells, but they are also needed for string connections in shingled solar cells. Accordingly, in this study, we researched the interconnection that best suits the connector that joins the string to the string. The module outputs produced under the conditions of the string interconnection were compared and analyzed.

As the demand for new and renewable energy increases due to the depletion of fossil fuels, solar power generation, a core energy source for new and renewable energy, requires research on solar modules for high output power generation. In this paper, the electrical characteristics of solar cell strip at the edge and in the center of single-crystal silicon having a semi-square shape were analyzed. The cell strip located in the center showed the efficiency increase by 0.26% compared to the cell strip at the edge of the solar cell. A shingled photovoltaic module was manufactured for each cell strip. As a result, the output power of the module using the cell strip located in the center was higher by 0.992%.

In this study, we fabricated light-weight solar module for various applications such as building integrated photovoltaics (BIPV), vehicles, trains, etc. Ethylene tetra fluoro ethylene (ETFE) film was applied as a material to replace the cover glass, which occupies more than 65% of the weight of the PV module. Glass fiber reinforced plastic (GRP) was applied to the ones with a low durability by replacing the cover glass to ETFE. Moreover, to achieve a high solar power conversion in this study, we applied a shingled design to weight reduced solar modules. The shingled module with GRP shows 183.7 W of solar-to-power conversion, and the output reduction rate after weight load test was 1.14%.

Recently, infrared (IR) and near-infrared (NIR) light-emitting diodes (LEDs) were widely used for home medical applications owing to its low output power and wide exposed area for curing. For deep penetration of the light under the skin, multiple LEDs with wavelengths of 700~10,000 nm were located on a flexible printed circuit board. When multiple wavelengths of LEDs were soldered on a circuit board, the lifetime of LED module highly depends on LEDs with a short lifetime. The mean time to failure (MTTF) was able to calculate with the experimental results under high temperature and the Arrhenius model. The results of this study could help companies to approve the warranty of LED modules and its product.

An increase in the temperature of photovoltaic (PV) modules causes reduced power output and shorter lifetime. Because of these characteristics, demands for the heat dissipation of PV modules are increasing. In this study, we attached a heat dissipation sheet to the back sheet of a shingled PV module and observed the temperature changes. The PV shingled module was tested under Standard Test Conditions (STCs; irradiance: 1,000 W/m², temperature: 25℃, air mass: 1.5) using a solar radiation tester, wherein the temperature of the PV module was measured by irradiating light for a certain duration. As a result, the temperature of the PV module with the heat dissipation sheet decreased by 3℃ compared to that without a heat dissipation sheet. This indicated that the power loss was caused by a temperature increase of the PV module. In addition, it was confirmed that the primary parameter contributing to the reduced PV module output power was the open circuit voltage (Voc).

The high power of a shingled photovoltaic module can be attributed to its low cell-to-module loss. The production of high power modules in limited area requires high efficiency solar cells. Shingled photovoltaic modules can be made by divided solar cells, which can be produced by the laser scribing process. After dividing the 21% PERC cell using laser scribing, the efficiency decreased by approximately 0.35%. However, there was no change in the efficiency of the solar cell having relatively lower efficiency, because the laser scribing process induce higher heat damages in solar cells with high efficiency. To prove this phenomena, the J₀ (leakage current density) of each cell was analyzed. It was found that the J₀ of 21% PERC increased about 17 times between full and divided solar cell. However, the J₀ of 20.2% PERC increased only about 2.5 times between full and divided solar cell.

In this study, we fabricated a metamorphic high-electron-mobility transistor (mHEMT) device with a T-type gate structure for the implementation of W-band monolithic microwave integrated circuits (MMICs) and investigated its characteristics. To fabricate the mHEMT device, a recess process for etching of its Schottky layer was applied before gate metal deposition, and an e-beam lithography using a triple photoresist film for the T-gate structure was employed. We measured DC and RF characteristics of the fabricated device to verify the characteristics that can be used in W-band MMIC design. The mHEMT device exhibited DC characteristics such as a drain current density of 747 mA/mm, maximum transconductance of 1.354 S/mm, and pinch-off voltage of -0.42 V. Concerning the frequency characteristics, the device showed a cutoff frequency of 215 GHz and maximum oscillation frequency of 260 GHz, which provide sufficient performance for W-band MMIC design and fabrication. In addition, active and passive modeling was performed and its accuracy was evaluated by comparing the measured results. The developed mHEMT and device models could be used for the fabrication of W-band MMICs.

In this paper, we prepared miniature fuse fabricated with carbon nanotube (CNT) fiber for the use of low rated current under 1 A and high speed operation under 4ms. CNT fuses were fabricated in the form of universal modular fuse (UMF) with different diameter of CNT fibers defined by multiplying the CNT threads. Electrical properties of the CNT fuses were measured such as resistance, rated current, and operation time with current. Resistance of the CNT fuse decreased and rated current increased with the diameter of the CNT fuses, respectively. Consequently, the operation time with current increased with the diameter of the CNT fuses. The CNT fuses fabricated in this work had broad range of low rated current from 0.05 to 1.25 A by multiplying the CNT threads. Operation time was measured about 3.6ms which was applicable to the UMF.

Recently, with the increase in the use of urban solar power, solar modules are required to produce high power in limited areas. In this report, we proposed the fabrication of a high-power photovoltaic module using shingles technology, and developed accurate string characteristic simulations based on circuit modeling. By comparing the resistance components between the interconnected cells and the cell strips, the ECA resistance was determined to be 0.003 Ω. Based on the equivalent circuit of the modeled shingled string, string simulation was performed according to the type of cell strip. As a result, it was determined that the cell efficiency of the 4-cell strip was the highest at 19.66%, but the efficiency of the string simulated with the 6-cell strip was the highest at 20.48% in the string unit.