Polymer nanocomposites incorporating inorganic nanofillers have emerged as highly promising electromagnetic interference (EMI) shielding materials, combining mechanical compliance with robust conductive percolation networks. Carbon nanotubes (CNTs) are particularly attractive as conductive fillers because their high aspect ratio facilitates percolation at low loadings. Also, CNTs offer superior mechanical durability under deformation compared to rigid, fracture-prone metal nanowires. For EMI shielding, high electrical conductivity is critical as it enhances both reflection and absorption through efficient charge dissipation and conduction losses. However, achieving highly aligned conductive pathways without degrading the intrinsic electrical properties of CNTs remains a significant challenge. Here, we demonstrate a non-destructive magnetic surface-functionalization and alignment strategy. Using a polydopamine (PDA)-mediated route, pristine multiwalled CNTs are uniformly decorated with Fe₃O₄ nanoparticles (FMWCNTs). This enables highly effective magnetic field-driven alignment at fields as low as 10 mT, promoting the strategic formation of percolation networks. By optimizing the Fe₃O₄/MWCNT ratio for high saturation magnetization and uniform coverage, the aligned FMWCNTs exhibit significant electrical anisotropy, delivering a 10.7-fold higher electrical conductivity in the parallel configuration compared to the vertical configuration. These findings present a scalable, room-temperature platform for engineering directionally enhanced conductivity in polymer nanocomposites, with broad applicability in advanced EMI shielding, flexible electronics, and advanced packaging technologies.

This paper proposes a circular sequential lighting control method to reduce current imbalance and luminance deviation among multiple LED modules in AC-powered LED lighting systems. Conventional fixed-sequence lighting control repeatedly prioritizes the same LED modules in every rectified voltage cycle, which leads to unequal current distribution, luminance non-uniformity, and the accelerated degradation of specific modules during long-term operation. To address these limitations, a circular sequential lighting strategy is introduced, in which the lighting order is cyclically rotated at every rectified cycle, ensuring that all LED modules experience equal lighting opportunities. A prototype AC-LED lighting system consisting of four series-connected LED modules was implemented and experimentally evaluated. The results demonstrate that, while the conventional fixed-sequence method produces a maximum average current deviation of up to 1.6 mA among modules, the proposed method equalizes the average current across all modules to approximately 17.1 mA. Furthermore, the flicker index remains at 0.13, which is comparable to that of the conventional method, indicating that luminance uniformity is improved without degradation of optical performance. The proposed circular sequential lighting control effectively distributes electrical stress, enhances luminance uniformity, and improves long-term reliability, making it a practical and efficient solution for high-quality AC-LED lighting applications.

Long lifetime, low power consumption, and environmental friendliness have enabled light-emitting diode (LED) lighting to rapidly replace conventional light sources such as incandescent and fluorescent lamps. In particular, AC-LED lighting systems can be directly powered by commercial alternating current (AC) sources; however, they suffer from significant luminance deviation caused by uneven current distribution among LED light-emitting modules. This paper proposes a lighting control method that improves flicker performance while maintaining lamp brightness and effectively reduces luminance deviation in AC-LED lighting. The proposed method reduces luminance deviation by controlling the lighting order of multiple LED light-emitting modules. Among four LED modules, only the required number of modules is continuously turned on, and the lighting priority alternates between rectification cycles. Specifically, during odd rectification cycles, LED modules are activated sequentially in ascending order (11→12→13→14), whereas during even rectification cycles, they are activated in descending order (14→13→12→11). By alternately applying continuous lighting control with opposite activation orders, the proposed reverse alternating lighting control method equalizes the current distribution among LED modules. As a result, luminance uniformity is improved, electrical stress concentration on specific modules is reduced, and the operational lifetime of the LED modules is extended compared with the conventional fixed-sequence lighting control method.

Micro-LEDs, which have a chip size of less than 100 × 100 μm², have been potential candidates for conventional LCDs and OLEDs due to their high optical power, outstanding stability, and nanosecond response time. However, Micro-LED chips are fabricated only on limited substrates due to the high-temperature metal-organic chemical vapor deposition process and lattice-mismatch issues. Therefore, the fabrication of Micro-LED displays requires complex processes such as chip fabrication, transfer, bonding, and repair. Especially, Micro-LED transfer and bonding have been critical challenges for the Micro-LED display commercialization. Here, recent advances in the transfer and bonding of Micro-LEDs are introduced, and novel Micro- LED display fabrication methods are reviewed to provide a practical outlook for both mass production and commercialization of Micro-LED displays.

With the advancement of the information society, the demand for highly integrated and multi-functional electronic devices is rapidly increasing. To meet these demands, high-performance transistors with low power consumption, high-speed operating, and mechanical flexibility are essential. Among various candidates, semiconducting single-walled carbon nanotubes (s-SWCNT)-based transistors, which exhibit intrinsically ambipolar characteristics, have emerged as promising components for CMOS-like circuits. In this study, s-SWCNT were selectively dispersed using rr-P3DDT, a thiophene-based conjugated polymer, and filed-effect transistors (FETs) were fabricated by inducting directional alignment for enhanced charge transport through an off-centered spin-coating process. The electrical characteristics of the fabricated s-SWCNT FETs were evaluated under various thermal annealing conditions (100℃, 150℃, 200℃, and 250℃). Off-centered spin-coated and high temperature annealed s- SWCNT FETs exhibited high field-effect mobilities over 5 cm²/Vs in both p-type and n-type operation, along with ideal Vshaped ambipolar transfer curves. These results indicate a significant enhancement in ambipolar performance due to efficient desorption of residual oxygen and water molecules in active channel via high temperature annealing. Furthermore, CMOS-like inverter circuits demonstrated an ideal inversion voltage (VIN = V_DD/2) and a high voltage gain of approximately 9.5. These findings highlight the potential of SWCNT-based materials for realizing next-generation flexible electronic circuits that combine high-performance, energy efficiency, and simplified solution-processing.

The thermal management issue in OLED (organic light emitting diode) devices has a significant impact on the efficiency, reliability, and life time of the device. In particular, in OLED systems with multipolar or double cathode electrodes, it is important to accurately interpret the effect of heat generated by current flow between electrodes on the emitting layer. In this study, the governing equation was established based on the heat conduction equation to mathematically model and analyze this heat distribution, and the heat distribution analysis was performed using the COMSOL program. It was confirmed that the temperature generated in the OLED with the double cathode structure reached a maximum of 343.157 K centered on the emitting layer. The heat distribution generated in the proposed OLED structure with the double cathode electrodes was confirmed to be highly distributed in the center toward the double cathode electrodes, which is believed to be because the arrangement of the double cathode electrodes improves the symmetrical distribution of temperature while reducing power consumption.

Neuromorphic computing, inspired by the biological mechanisms of neural signal transmission, has emerged as a promising technology for efficient and parallel data processing with minimal power consumption. In this study, we developed floating-gate organic thin-film transistors (OTFTs) with self-assembled monolayer (SAM)-based tunneling layers to mimic the characteristics of artificial synapses. The tunneling layers were formed using mixed phosphonic acid SAMs with varying ratios of octadecylphosphonic acid (ODPA) and 12-pentafluorophenoxydodecylphosphonic acid (PFPA). The influence of these ratios on the memory and neuromorphic characteristics of the devices was systematically evaluated. Our results revealed that the ODPA ratio significantly impacts the hysteresis window, with higher ODPA content yielding improved memory characteristics. Conversely, the PFPA : ODPA ratio of 2:1 exhibited the lowest non-linearity (NL = 0.48), demonstrating the potential for highly accurate weight updates in neuromorphic devices. Additionally, pulse width modulation studies showed that a pulse width of 100 ms optimized the linearity and stability of long-term potentiation (LTP) and depression (LTD) characteristics. The combination of sol-gel processed AlOx as a floating-gate layer and tailored SAM-based tunneling layers allowed for precise control of device performance. These findings highlight the importance of molecular engineering in designing SAM layers to balance memory retention and neuromorphic functionality. This study provides a pathway for advancing organic floating-gate transistors as a core component in next-generation neuromorphic computing systems.

This study explores the realization of high-efficiency white LED lighting by applying cyan-emitting quantum dot (CQD) and red-emitting quantum dot (R-QD) deposition without any host matrix onto a yellow-emitting phosphor-in-glass (YPIG) substrate using an aerosol-assisted deposition (AAD) process. The AAD process facilitates the direct formation of densely packed QD-deposited layers on the substrate, effectively addressing challenges such as optical efficiency loss and degradation typically associated with organic host matrices. C-QD and R-QD coatings, deposited with thicknesses of 0.84 μm and 0.77 μm on the upper and lower Y-PIG substrate, exhibited robust color conversion properties. These films achieved a luminous efficacy of 77 lm/W and a high color rendering index (CRI) of 96.8 under blue light excitation. The dual-layer structure produced highquality light closely resembling natural daylight, as confirmed through real image. Consequently, the research suggests the potential of AAD-based QD deposition to achieve superior performance without relying on host matrices, offering a viable solution for high-efficiency lighting applications. Further optimization of deposition parameters and exploration of diverse substrates and QD material combinations are expected to expand the applicability of this technique in future research.

Human-centric lighting (HCL) aims to enhance well-being and performance by tailoring lighting to human needs. However, LED flicker-rapid brightness changes-remains a critical issue, causing discomfort and reduced productivity. This paper addresses flicker problems in living and industrial spaces with LED lighting. We propose solutions to mitigate flicker by examining causes like power supply variations and LED driver design. Techniques such as high-quality LED drivers, advanced dimming methods, and digital control systems are explored. Our findings show these techniques can significantly reduce flicker, achieving less than 1% flicker performance while meeting HCL’s diverse requirements. Implementing flicker-free lighting in residential spaces enhances comfort and reduces eye strain, while in industrial settings, it improves productivity and safety. This paper emphasizes the importance of control circuits that maintain sub-1% flicker performance while integrating various HCL solutions, enhancing indoor lighting quality, and promoting better health and performance.

Lighting has been used for a long time as a medium to convey brightness from darkness, and through incandescent lamps and fluorescent lamps, LED light sources have now become the standard in the lighting industry. Recently, the lighting equipment industry has been undergoing rapid digital transformation, starting with smart lighting, and is evolving into smart lighting customized for individuals and spaces through the development of IoT technology, cloud-based services, and data analysis. However, the blue light emitted from digital devices (computers, smartphones, tablets, etc.) or LED lights stimulates the melanopsin in the optic ganglion cells in the retina of the eye, which in turn stimulates the secretion of melatonin through the pineal gland, which regulates the secretion of melatonin. This can reduce sleep quality or disrupt biological rhythms. This interaction between blue light and melatonin has such a significant impact on human sleep patterns and overall health that it is essential to reduce exposure to blue light, especially in the evening. Human-centered lighting refers to lighting that takes into account the effects of light on the physical and mental areas, such as human activity and awakening, improvement of sleep quality, and health management. Many research institutes study the effects in the visible area and the non-visible area. By studying the impact, it is expected to improve the quality of human life. In this study, we plan to study ways to implement humancentered lighting by collecting sunrise and sunset data and linking commercialized LED packages and control devices with opensource hardware.

The key to determining the lifetime of OLED device is how much brightness can be maintained. It can be said that there are internal and external causes for the degradation of OLED devices. The most important cause of internal degradation is bonding and degradation in the excited state due to the electrochemical instability of organic materials. The structure of OLED modeled in this paper consists of a cathode layer, electron injection layer (EIL), electron transport layer (ETL), light emission layer, hole transport layer (HTL), hole injection layer (HIL), and anode layer on a glass substrate from top to bottom. It was confirmed that the temperature generated in OLED was distributed around the maximum of 343.15 K centered on the emission layer. It can be seen that the heat distribution generated in the presented OLED structure has an asymmetrically high temperature distribution toward the cathode, which is believed to be because the sizes of the cathode and positive electrode are asymmetric. Therefore, when designing OLED, it is believed that designing the structures of the cathode and anode electrodes as symmetrically as possible can ensure uniform heat distribution, maintain uniform luminance of OLED, and extend the lifetime. The thermal distribution of OLED was analyzed using the finite element method according to Comsol 5.2.

Micro light-emitting diodes (LEDs), with a chip size of 100 micrometers or less, have attracted significant attention in flexible displays, augmented reality/virtual reality (AR/VR), and bio-medical applications as next-generation light sources due to their outstanding electrical, optical, and mechanical performance. In the realm of bio-medical devices, it is crucial to transfer tiny micro LED chips onto desired flexible substrates with low precision errors, high speed, and high yield for practical applications on various parts of the human body, including someone’s face and organs. This paper aims to introduce a fabrication process for flexible micro LED devices and propose micro LED transfer techniques for cosmetic and medical applications. Flexible micro LED technology holds promise for treating skin disorders, cancers, and neurological diseases.

In this paper, in order to apply the CF (color filter) type of the micro light emitting device (Micro LED) display method, a study on the manufacturing process of red and green phosphor inks for the inkjet process was conducted. The blue light-emitting KSF and LuAG phosphors were respectively used to control the phosphor particle size to about 1μm, and a phosphor ink was prepared by synthesizing with a low-viscosity solution (IPA/Eg). A chemical dispersion method was applied to selectively control the dispersion characteristics in the manufacture of phosphor inks, and in particular, phosphor inks with a dispersant applied a dispersant secured stable dispersion characteristic compared to phosphor inks without a dispersion process. Therefore, it seems possible to manufacture CF for Micro LED through an inkjet process capable of controlling the dispersion characteristics of phosphor ink.

We have developed inverted green phosphorescent organic light emitting diodes (OLEDs) using 1,1-bis[(di-4- tolylamino)phenyl]cyclohexane (TAPC) and bis(carbazole-9-yl)biphenyl (CBP) hole transport layers. The driving voltage, current efficiency, power efficiency, and emission characteristics of devices were investigated. While the driving voltage for the same current density was about 1~2 V lower in the devices with the TAPC layer, the maximum luminance was higher in the device with the CBP layer. The maximum current efficiency and power efficiency were 3.2 and 2.7 times higher in the device with the CBP layer, respectively. The higher efficiency in the CBP device resulted from the enhanced hole-electron balance although weak parasitic recombination takes place in the CBP hole transport layer.

Recently, sterilization technology has received increasing interest due to the COVID-19 pandemic and required safety precautions. Particularly, sterilization devices using near ultraviolet (UV) with a 405 nm wavelength are also drawing attention. It has a UV-C wavelength and other sterilization effects. Its blue-colored light on the boundary between UV and visible light is used as a light-emitting diode (LED) lamp for 405 nm sterilization, owing to its longer wavelengths than UV rays. However, the 405 nm wavelength contains blue light that can damage the eyes and skin during prolonged exposures and affect the emotional and biological parts of the body. Currently, 405 nm sterilization LED light registers are circulating in the market. However, they have not undergone safety tests for blue-light hazards. Thus, with the active distribution of sterilization LED lights, solid safety standards and management systems are essential to protect users from blue-light hazards. Accordingly, in this study, we conducted spectral radiance and spectral radiative luminance tests on 405 nm sterilization LED registers available in the market by the measurement criteria of IEC 62471. Safety standards must be established to secure users' safety against blue light hazards at a time when 405nm sterilization LED lights are actively distributed due to COVID-19.

In order to spread LED lighting, LED lighting technology directly driven by alternating current (AC) commercial power has recently been introduced. Since current does not flow at a voltage lower than the threshold voltage of the LED, a nonconductive section occurs in the current waveform, and the higher the threshold voltage of the LED, the more discontinuous current waveforms are generated. In this paper, multi-LED modules are connected in series so that the threshold voltage can be adjusted according to the number of LED modules. A small number of LED modules are driven at a low instantaneous rectified voltage, and a large number of LED modules are driven at a high instantaneous rectified voltage to lengthen the overall lighting time of AC-LED lighting, thereby minimizing the luminance deviation of AC-LED lighting. In addition, the load current flowing through the LED module is adjusted to be the same as the design current even at the maximum rectified voltage higher than the design voltage, so that the light brightness of the LED module is kept constant. Therefore, even if the rectified voltage applied to the LED module changes, the AC-LED lighting in which the light brightness is constant and the luminance deviation is minimal has been realized.

In order to widely disseminate LED lighting, LED lighting technology that directly uses AC commercial power has been recently introduced. AC powered LED lighting technology has a problem in that the light brightness of the LED changes because the voltage applied to the LED and the current flowing through the LED continuously change. In this study, when the LED current is greater than the design current, the current control signal generated by the controller is supplied to the current source to supply only the design current to the LED by increasing the voltage drop at the current source. If it is smaller than the design current, the controller is adjusted so that the current is supplied only to the LED without a voltage drop in the current source. It can be seen that the higher the maximum rectified voltage, the faster the lighting time of the LED light emitting block is, so that the power factor of the LED lighting is improved. The LED lighting technology proposed in this study enables LED lighting with constant light brightness, reduced power consumption, and long lifetime.

Global warming is accelerating due to the use of fossil fuels that have been used continuously for centuries. Now, humankind recognizes its seriousness, and is conducting research on searching for eco-friendly and sustainable energy. In the field of solar energy, which is a kind of eco-friendly and sustainable, many studies are being conducted to enhance the output performance of the module. In this study, the output improvement for the shingled module structure was studied. In order to improve the output performance of the module, the thickness of the encapsulant was increased, and the lamination process conditions have been improved accordingly. After that, the crosslinking rate was analyzed, and the suitability of the lamination process conditions was judged using this. In addition, a peeling test was conducted to analyze the correlation between the adhesion of the encapsulant and the output performance of the module. Finally, the optimization for the encapsulant material and the lamination process conditions for high-power shingled modules was established, and accordingly, the market share of high-power shingled modules in the solar module market can be expected to rise.

The SiO₂/TiO₂ multilayer thin films used for narrow band pass filter were fabricated using E-beam evaporation method. The narrow band pass filter was used to enhance the resolution of spectroscopy and sensor applications with near infrared (NIR) light source. The narrow band pass filter with multilayer thin films were designed with Essential Macleod program. The multilayers of SiO₂/TiO₂ with 32 layers were deposited on the silicon encapsulation of IR with peak wavelength (λp) of 660 nm and NIR LEDs with λp of 830 nm, 880 nm, and 955 nm. After NIR light passed through the narrow band pass filter, the full width of half maximum of 33.4~48.6 nm became narrow to 20~24 nm owing to the absorption of photons with short or long wavelength of designed band of 20 nm. The SiO₂/TiO₂ band pass filter fabricated in this study can be used for sensor, optoelectronics, and NIR spectroscopy applications.

We report highly efficient quantum dot light-emitting diodes (QLEDs) with TiO2 nanoparticles (NPs) as an alternative electron transport layer (ETL) and poly (methyl methacrylate) (PMMA) as an insulating layer. TiO₂ NPs were applied as ETLs of inverted structured QLEDs and the effect of the addition of PMMA between ETL and emission layer (EML) on device characteristics was studied in detail. A thin PMMA layer supported to make the charge balance in the EML of QLEDs due to its insulating property, which limits electron injection effectively. Green QLEDs with a PMMA layer produced the maximum luminance of 112,488 cd/㎡ and a current efficiency of 25.92 cd/A. We expect the extended application of TiO₂ NPs as the electron transport layer in inverted structured QLEDs device in the near future.

Interest and investment in renewable energy have increased worldwide, highlighting the need for renewable energy. Solar energy was the most promising energy of all renewable energy sources, and it has the highest investment value. Because photovoltaics require a certain amount of area for installation, high density and high output performance are required. Shingled module is a promising technology in that they are featured by higher density and higher output compared to the conventional modules. Shingled technology uses a laser scribing to divide solar cells that are to be bonded with electrically conductive adhesive (ECA) to produce and connect strings, which has a higher output in the same area than the conventional modules. In the process of producing solar modules, metal ribbons are used to interconnect cells, but they are also needed for string connections in shingled solar cells. Accordingly, in this study, we researched the interconnection that best suits the connector that joins the string to the string. The module outputs produced under the conditions of the string interconnection were compared and analyzed.

As the demand for new and renewable energy increases due to the depletion of fossil fuels, solar power generation, a core energy source for new and renewable energy, requires research on solar modules for high output power generation. In this paper, the electrical characteristics of solar cell strip at the edge and in the center of single-crystal silicon having a semi-square shape were analyzed. The cell strip located in the center showed the efficiency increase by 0.26% compared to the cell strip at the edge of the solar cell. A shingled photovoltaic module was manufactured for each cell strip. As a result, the output power of the module using the cell strip located in the center was higher by 0.992%.

With the advent of the IoT (internet of things) era, there has been discussion on how to efficiently use various information from daily life. In academic and industrial society, various smart devices such as smart watches, smart phones, and smart glasses have been developed and commercialized for narrowing the physical/psychological distance with user information. According to recent developments of smart devices, the contemporary people have desired to check their body information and treat disease by themselves. According to the needs of the time, biological researches by phototherapy/monitoring have been actively conducted. Among various light sources, microLEDs have been spotlighted due to their superior optoelectric properties and stability. In this paper, we would like to review the state-of-the research results on the next-generation biological therapy devices via microLEDs.

A machine vision inspection system consists of a camera, optics, illumination, and image acquisition system. The illumination system among these uses LED lighting source. Therefore, the driving method of LED lighting source is very important. The two main driving methods of LED lighting system for machine vision are Pulse Width Modulation (PWM) control driving and strobe control driving. PWM control driving method has problems such as a temperature rising of LED and a flickering in image measurement for inspection. On the other hand, strobe control driving method has a difficulty in the control of light intensity because of too short on-time. In this study, we propose a new hybrid-dimming control driving method for LED lighting source for machine vision. The proposed new hybrid-dimming control driving method can control current intensity and current on-time simultaneously so that it can extract clearer images with a high precision without the light saturation of image.

Inductively coupled plasma reactive ion etching (ICP-RIE) of copper thin films patterned with SiO₂ hard masks was carried out using piperidine/O₂/Ar gas mixture. The etch rate, etch selectivity, and etch profile of copper thin films were investigated by varying gas concentration in piperidine/O₂/Ar gas mixture. In addition, the etch parameters including ICP RF power, DC-bias voltage to substrate, and process pressure were varied to examine the etch characteristics. X-ray photoelectron spectroscopy and optical emission spectroscopy were employed to elucidate the etch mechanism under piperidine/O₂/Ar gas chemistry. Finally, 150 nm-line patterned copper thin films were successfully etched using piperidine/ O₂/Ar etch gas under the optimized etch conditions.

The machine vision technology has been widely used in the industrialized nations like the United States, Japan, and EU in the various industries from the late 1980s. Machine vision inspection system mainly consists of a camera, optics, illumination and an image acquisition system. Optimization of the illumination light source is very important. This paper shows a comparison between Pulse Width Modulation (PWM) control and strobe control in driving LED lighting system for machine vision. PWM control method has problems such as a temperature rising of LED and a flickering in image measurement for inspection. In contrast, the proposed strobe control method can suppress the temperature of LED light source below 40℃. Also, it can remove the flickering problem through a synchronization between a frame grabber and a camera shutter. Finally, the strobe control method was shown to extract clearer images with a high precision compared to PWM control method.

In this study, we fabricated light-weight solar module for various applications such as building integrated photovoltaics (BIPV), vehicles, trains, etc. Ethylene tetra fluoro ethylene (ETFE) film was applied as a material to replace the cover glass, which occupies more than 65% of the weight of the PV module. Glass fiber reinforced plastic (GRP) was applied to the ones with a low durability by replacing the cover glass to ETFE. Moreover, to achieve a high solar power conversion in this study, we applied a shingled design to weight reduced solar modules. The shingled module with GRP shows 183.7 W of solar-to-power conversion, and the output reduction rate after weight load test was 1.14%.

Recently, infrared (IR) and near-infrared (NIR) light-emitting diodes (LEDs) were widely used for home medical applications owing to its low output power and wide exposed area for curing. For deep penetration of the light under the skin, multiple LEDs with wavelengths of 700~10,000 nm were located on a flexible printed circuit board. When multiple wavelengths of LEDs were soldered on a circuit board, the lifetime of LED module highly depends on LEDs with a short lifetime. The mean time to failure (MTTF) was able to calculate with the experimental results under high temperature and the Arrhenius model. The results of this study could help companies to approve the warranty of LED modules and its product.

Micro-LEDs can be applied to various parts of a product. However, it has disadvantages compared to general LEDs in large displays such as low efficiency, intensity, and contrast ratio, among others, owing to their short history of study. The simulations were carried out using ray-tracing software to investigate the change in light intensity and light distribution according to pattern shapes on the sapphire substrate of the flip-chip micro-LED (FC μ-LED) array. Three patterns-concave square patterns, convex square patterns, and Ag coated convex patterns-which existed on the opposite side of FC μ-LEDs (115 ㎛ × 115 ㎛) array, were applied. The intensity of FC μ-LEDs on the center of the receivers depends on the pattern depth with shape. The concave square patterns having FC μ-LEDs arrays show that decreasing intensity as the patterns depth. On the contrary, the convex square patterns having FC μ-LEDs arrays shows that increasing intensity as the patterns depth. In addition, the highest intensity shows that FC μ-LEDs having Ag-coated convex patterns on the opposite side of sapphire lead to a reduction in light crosstalk owing to the Ag film.

An increase in the temperature of photovoltaic (PV) modules causes reduced power output and shorter lifetime. Because of these characteristics, demands for the heat dissipation of PV modules are increasing. In this study, we attached a heat dissipation sheet to the back sheet of a shingled PV module and observed the temperature changes. The PV shingled module was tested under Standard Test Conditions (STCs; irradiance: 1,000 W/m², temperature: 25℃, air mass: 1.5) using a solar radiation tester, wherein the temperature of the PV module was measured by irradiating light for a certain duration. As a result, the temperature of the PV module with the heat dissipation sheet decreased by 3℃ compared to that without a heat dissipation sheet. This indicated that the power loss was caused by a temperature increase of the PV module. In addition, it was confirmed that the primary parameter contributing to the reduced PV module output power was the open circuit voltage (Voc).