Recently, as environmental issues caused by gas stoves have led to the widespread adoption of induction appliances, specialized cookware for induction is essential. However, due to the inability of ceramic containers to be directly used on induction cooktops, a conductive coating is required on the bottom of the cookware, presenting limitations such as complex deposition processes and extended coating times in existing methods including thermal spraying, dip coating, and transcription method. We confirmed the potential of heat-resistant cookware for induction use by coating the bottom of the ceramic container with Ag through a simple manufacturing process of screen-printing and measuring its thermal conductivity and reliability. The Ag-coated ceramic cookware produced by screen-printing demonstrated similar thermal conductivity and reliability to those made using the traditional method of transfer printing. In addition, the adhesive strength before and after thermal shock testing was even superior in the screen-printing method, which suggests a higher expected lifespan. As a result, it is expected that induction-compatible heat-resistant ceramic containers with excellent performance and lifespan will be manufactured through the screen-printing process, which is more cost-effective and efficient compared to other methods.

The high power of a shingled photovoltaic module can be attributed to its low cell-to-module loss. The production of high power modules in limited area requires high efficiency solar cells. Shingled photovoltaic modules can be made by divided solar cells, which can be produced by the laser scribing process. After dividing the 21% PERC cell using laser scribing, the efficiency decreased by approximately 0.35%. However, there was no change in the efficiency of the solar cell having relatively lower efficiency, because the laser scribing process induce higher heat damages in solar cells with high efficiency. To prove this phenomena, the J₀ (leakage current density) of each cell was analyzed. It was found that the J₀ of 21% PERC increased about 17 times between full and divided solar cell. However, the J₀ of 20.2% PERC increased only about 2.5 times between full and divided solar cell.

Recently, with the increase in the use of urban solar power, solar modules are required to produce high power in limited areas. In this report, we proposed the fabrication of a high-power photovoltaic module using shingles technology, and developed accurate string characteristic simulations based on circuit modeling. By comparing the resistance components between the interconnected cells and the cell strips, the ECA resistance was determined to be 0.003 Ω. Based on the equivalent circuit of the modeled shingled string, string simulation was performed according to the type of cell strip. As a result, it was determined that the cell efficiency of the 4-cell strip was the highest at 19.66%, but the efficiency of the string simulated with the 6-cell strip was the highest at 20.48% in the string unit.

Advances in laser technology have enabled ultra-high-speed ultra-precise processing, thus expanding potential applications to the semiconductor, medical, and photovoltaic industries. In particular, laser scribing technology has been applied to the production of shingled solar modules. In this work, we analyze the effect of laser scribing conditions, e.g., scribing depth, on the characteristics of the resulting divided solar cells. When the scribing depth was greater than 100 ㎛, the solar cells were well separated. In addition, the desired scribing depths were reached in fewer scans when the laser spot overlap was 100%. The efficiency of the divided cells decreased due to the high series resistance at scribing depths of less than 100 ㎛. However, at scribing depths of approximately 100 ㎛, the series resistance was low and efficiency reduction was minimized.

TiN thin films were fabricated using an unbalanced magnetron sputtering (UBMS) system, and their structure and surface characteristics as well as their optical and tribological properties were evaluated. The hardness, elastic modulus, adhesive force, surface roughness, and transmittance of the Ti thin films fabricated using the UBMS system were 11.5 GPa, 103 GPa, 27.5 N, 2.45 nm and 20%, respectively. The TiN films prepared with various proportions of nitrogen as the reaction gas exhibited maximum values for the hardness, elastic modulus, critical load, RMS roughness and transmittance of approximately 19.2 GPa, 182 GPa, 27.3 N, 0.98 nm, and 85%, respectively. Moreover, the TiN thin film fabricated under the condition of 30 sccm nitrogen gas showed the optimal physical properties. In summary, the TiN thin films fabricated using the UBMS system exhibited excellent hardness, elastic modulus, adhesion, and smooth surface in addition to good hydrophilic properties.

Eight types of LED packages were manufactured according to the type and composition ratio of phosphors by using commercially available white LED phosphors. CRI (Ra), a conventional color quality evaluation method was evaluated by using manufactured white LED; the Rf, Rg, color vector graphic, and color distortion graphic were evaluated with a new method, IES TM-30-15. The results of the evaluation confirmed that the new method compensated for the disadvantages of CRI, which was found to be inadequate when the color was saturated. The added evaluation index identified the chroma variation and color change. Furthermore, the study showed that the changes of Rf and Rg are small when controlling phosphors based on CRI, questioningthe necessity of identifyingchroma variation and color change.

We developed a Ag nanowire patterning technique using a water-soluble sacrificial layer. To form a water-soluble sacrificial layer, germanium was deposited on the substrate and then water-soluble germanium oxide was simply formed by thermal oxidation of germanium using a conventional furnace. The formation of Ag nanowire patterns with various line and space arrangements was successfully demonstrated using this patterning process. The main advantage of this patterning technique is that it does not use a strong acid etchant, thereby preventing damage to the Ag nanowire during the patterning process.

Power MOSFETs (metal oxide semiconductor field effect transistor) operate as energy control semiconductor switches. In order to reduce energy loss of the device, it is essential to increase its conductance. However, a trade-off relationship between the breakdown voltage and conductance of the device have been the critical difficulty to improve. In this paper, theoretical analysis of electrical benefits on single floating island power MOSFET is proposed. By the method, the optimization point has set defining the doping limit under single floating island structure. The numerical multiple 2.22 was obtained which indicates the doping limit of the original device, improving its ON state voltage drop by 45%.

The characteristics of dielectric constant and tanδ of low viscosity silicone oils with changing degree of polymerization were investigated. The result shows dipole loss mechanism at low temperature range. The dielectric loss in the range of low frequencies are predominantly of ionic nature with temperature increase. The peak of dielectric loss is the detrapping of the electrons which is were trapped in the localized level of the silicone oils at the frequency of 30 kHz. The increase of ionic conduction is attributed to the presence of ionizable oxidation products and their increased dissociation feature. The activation energy △H and dipole moment μd were increased whit increasing degree of polymerization.

Oxides possess several interesting properties, such as ferroelectricity, magnetism, superconductivity, and multiferroic behavior, which can effectively be used oxide electronics based on epitaxially grown heterostructures. The microscopic properties of oxide interfaces may have a strong impact on the electrical transport properties of these heterostructures. It was recently demonstrated that high electrical conductivity and mobility can be achieved in the system of an ultrathin LaAlO3 film deposited on a TiO2-terminated SrTiO3 substrate, which was a remarkable result because the conducting layer was at the interface between two insulators. In this study, we observe that the current-voltage characteristics exhibit LaAlO3 thickness dependence of electrical conductivity in TiO2-terminated SrTiO3. We find that the LaAlO3 layers with a thickness of up 3 unit cells, result in highly insulating interfaces, whereas those with thickness of 4 unit cells and above result in conducting interfaces.