Dye-sensitized solar cells (DSSCs) suffer from efficiency limitations due to interfacial charge recombination at the TiO₂/dye/electrolyte interface. In this study, aminopropyltrimethoxysilane (APS) was introduced onto nanoporous TiO₂ photoelectrodes via a dip-coating process with controlled coating times to investigate the effect of silanization time on interfacial charge transport behavior. Unlike concentration-driven structural modification, this work focuses on the evolution of the APS-modified interface governed by reaction time. The DSSC with 30 min APS treatment exhibited the highest power conversion efficiency of 5.34%, representing a 19% enhancement compared to the untreated device (4.49%), mainly due to increased short-circuit current density and open-circuit voltage. However, prolonged coating times (2 h and 24 h) resulted in a significant decrease in photocurrent density, leading to reduced device performance despite partial improvement in recombination resistance. These results are attributed to the time-dependent evolution of the APS interfacial layer. At moderate coating time, APS provides effective surface functionalization, enhancing dye adsorption and suppressing interfacial recombination. In contrast, prolonged coating is expected to induce increased surface coverage and silane condensation, which can hinder electron injection and increase charge transport resistance. Therefore, the photovoltaic performance is governed by a trade-off between recombination suppression and charge injection efficiency, controlled by the silanization time. This study highlights the critical role of interfacial reaction kinetics in determining charge transport behavior and provides an effective strategy for optimizing DSSC performance through time-dependent interface engineering.

Citations

• Enhanced charge transport characteristics of hydrothermally grown rutile TiO2 nanorod arrays for dye-sensitized solar cells
  Kyu Seop Choi, Hyung Jin Kim, Byungyou Hong
  Surfaces and Interfaces.2026; 98: 110402.     CrossRef

Dye adsorption is one of the most time-consuming processes in the fabrication of dye-sensitized solar cells (DSSCs), typically requiring approximately 24 h at room temperature. In this study, the effect of adsorption temperature and time on photovoltaic performance of DSSCs was investigated in order to reduce processing time and improve device productivity. Nanoporous TiO₂ photoelectrodes were immersed in N719 dye solution at 60°C for 3 h, 10 h, 17 h, and 24 h, and their performance was compared with that of cells sensitized at room temperature for 24 h. Photovoltaic characterization under AM 1.5 illumination showed that DSSCs sensitized at 60°C exhibited improved performance compared to those sensitized at room temperature. The device sensitized at 60°C for 3 h showed comparable or higher conversion efficiency than the reference cell sensitized for 24 h at room temperature. The improvement in device performance is attributed to enhanced dye adsorption kinetics resulting from increased reaction rate between the carboxyl groups of N719 dye molecules and hydroxyl groups on the TiO₂ surface. Electrochemical impedance spectroscopy analysis revealed reduced recombination resistance at the TiO₂/dye/electrolyte interface for cells sensitized at elevated temperature. UV–Vis absorption analysis confirmed increased dye loading on the TiO₂ surface for the 60°C condition. These results demonstrate that elevated temperature dye adsorption significantly reduces processing time while maintaining photovoltaic performance, providing an effective strategy for improving manufacturing efficiency of DSSCs.

Citations

• Enhanced charge transport characteristics of hydrothermally grown rutile TiO2 nanorod arrays for dye-sensitized solar cells
  Kyu Seop Choi, Hyung Jin Kim, Byungyou Hong
  Surfaces and Interfaces.2026; 98: 110402.     CrossRef

DSSCs efficiency by thickness of TiO2 photoelectrode and thickness differences between two substrates studied. DSSCs is made of the doctor blade method and photoelectrode annealing temperature elevated in a different ways. In addition, cells efficiencies of according to the different thickness between TiO2 photoelectrode substrate and Pt counter electrode was measured. Efficiency of DSSCs made with TiO2 photoelectrode of 18 ㎛thickness and the gap difference between the substrate 28 ㎛shows a highest 4.805% efficiency.

Citations

• Effect of APS Dip-Coating Time on Interfacial Charge Transport in Dye-Sensitized Solar Cells
  Jin Wook Lee, Minjae Shin, Byungyou Hong, Hyung Jin Kim
  Journal of Electrical and Electronic Materials.2026; 39(4): 387.     CrossRef
• Effect of Dye Adsorption Time at Constant Temperature on the Photovoltaic Performance of Dye-Sensitized Solar Cells
  Ba Wi Hwang, Hyung Jin Kim, Byungyou Hong
  Journal of Electrical and Electronic Materials.2026; 39(4): 382.     CrossRef
• Time Dependent Degradation of Cell in Dye-Sensitized Solar Cell
  Hyun Woo Seo, Ki Soo Kim, Hyun Duk Beak, Dong Min Kim
  Transactions of the Korean hydrogen and new energy society.2013; 24(5): 421.     CrossRef