This study proposes an optimization strategy for the over-current protection (OCP) parameters of a lithium iron phosphate (LiFePO₄, LFP) battery system used in electric golf carts operating under high motor-load conditions. Real-world hillclimbing tests were conducted under four clearly defined payload/passenger conditions to analyze the transient discharge-current pro-file, voltage sag, and cell-temperature response. The maximum discharge current reached -238.2 A under the 200 kg cargopayload and one-passenger condition, and the current interval exceeding 150 A lasted up to 27 s. The maximum instantaneous power was 11.05 kW. Thermal analysis showed that the cell-temperature rise was within 2°C and the maximum measured cell temperature was 22.3°C. Linear regression of voltage and current yielded R² = 0.9368 and dV/dI = 0.0126 Ω, which was used as the DC internalresistance estimate. Based on these quantitative results and the cell specification limit of 300 A continuous discharge, the OCP threshold was reviewed from 250 A to 280 A to improve driving continuity while remaining below the allowable continuous-discharge current. EIS-based SOH estimation and the AI-BMS variable protection logic are presented as an extension framework for reflecting temperature and aging effects in future OCP-setting decisions.

Polymer nanocomposites incorporating inorganic nanofillers have emerged as highly promising electromagnetic interference (EMI) shielding materials, combining mechanical compliance with robust conductive percolation networks. Carbon nanotubes (CNTs) are particularly attractive as conductive fillers because their high aspect ratio facilitates percolation at low loadings. Also, CNTs offer superior mechanical durability under deformation compared to rigid, fracture-prone metal nanowires. For EMI shielding, high electrical conductivity is critical as it enhances both reflection and absorption through efficient charge dissipation and conduction losses. However, achieving highly aligned conductive pathways without degrading the intrinsic electrical properties of CNTs remains a significant challenge. Here, we demonstrate a non-destructive magnetic surface-functionalization and alignment strategy. Using a polydopamine (PDA)-mediated route, pristine multiwalled CNTs are uniformly decorated with Fe₃O₄ nanoparticles (FMWCNTs). This enables highly effective magnetic field-driven alignment at fields as low as 10 mT, promoting the strategic formation of percolation networks. By optimizing the Fe₃O₄/MWCNT ratio for high saturation magnetization and uniform coverage, the aligned FMWCNTs exhibit significant electrical anisotropy, delivering a 10.7-fold higher electrical conductivity in the parallel configuration compared to the vertical configuration. These findings present a scalable, room-temperature platform for engineering directionally enhanced conductivity in polymer nanocomposites, with broad applicability in advanced EMI shielding, flexible electronics, and advanced packaging technologies.

GaN nanowire (NW)-based hybrid structures have attracted attention for optoelectronic applications due to their high surface area and efficient carrier transport. However, the optical transparency of GaN NWs is often limited by unintended residual species accumulated on the surface and in the inter-wire regions, as well as defect-related absorption, leading to reduced light transmission. In this work, we demonstrate that thermal annealing significantly improves the optical transparency of GaN NWs grown on indium tin oxide (ITO)/glass substrates. The transmittance increased from 47.9% to 78.5% at 550 nm after rapid thermal annealing at 800^oC for 3 min, while a comparable value (~75.5%) was achieved at 600^oC for 5 min. PbBr₃ was deposited onto the GaN NWs to form hybrid structures, and temperature-dependent photoluminescence (TDPL) measurements revealed enhanced emission stability with suppressed peak shift and reduced spectral broadening. Arrhenius analysis based on a two-channel model revealed that the activation energy of the dominant non-radiative recombination pathway increased from 62 meV in the as-grown sample to 85 meV after thermal annealing, while its relative contribution remained nearly unchanged. In contrast, the shallow trap-assisted pathway exhibited a similar activation energy of approximately 6 meV in both samples, but its contribution decreased from 0.35 to 0.17 after annealing. As a result, the internal quantum efficiency (IQE) improved from 75.9% to 87.4%. These results show that thermal annealing improves optical transparency by removing residuals and suppresses defect-related recombination, leading to enhanced carrier dynamics and improved optical performance of PbBr₃-based hybrid structures.

Organic photovoltaics (OPVs) are attractive candidates for sustainable energy conversion due to their flexibility, lowcost processing, and compatibility with large-area fabrication. However, their efficiency is hindered by interfacial defects and vertical phase separation in the active layer, which induce charge imbalance and recombination losses. This work presents an interfacial engineering approach to overcome these limitations in P3HT:PC₇₀BM-based OPVs. Two key strategies were employed: (i) reducing the post-deposition annealing time of the active layer to suppress PC₇₀BM accumulation at the bottom electrode, and (ii) using a DCB:DCM mixed solvent system to regulate solvent evaporation, thereby promoting uniform film formation during PC₇₀BM overlay deposition. Devices fabricated with these optimizations exhibited notable enhancements, achieving short-circuit current density up to 15.83 mA/cm² and a 58.1% increase in power conversion efficiency compared to control devices. X-ray photoelectron spectroscopy confirmed reduced surface aggregation of PC₇₀BM, while X-ray diffraction indicated improved P3HT crystallinity and molecular ordering. These results highlight the critical role of interfacial and morphological control in enhancing charge separation and transport, offering a practical route toward efficient, reproducible, and stable OPVs.

e investigated the effects of post-annealing in vacuum, nitrogen, and hydrogen atmospheres on the structural, electrical, and optical properties of 600 nm thick Al-doped ZnO (ZnO:Al) thin films deposited by RF magnetron sputtering at room temperature. Post-annealing in hydrogen atmosphere at 400℃ for 1 hour showed the most significant improvement in electrical properties. Resistivity decreased from 9.11×10⁻³ to 1.4×10⁻³ Ω·cm, electron mobility increased from 4.11 to 18.23 cm²/V·s, and electron carrier concentration increased from 1.63×10²⁰ to 4.85×10²⁰ cm⁻³. In contrast, post-annealing in vacuum and nitrogen atmospheres resulted in degraded electrical properties due to oxygen and nitrogen chemisorption at grain boundaries. The enhancement in hydrogen-annealed films was attributed to the formation of additional oxygen vacancies and desorption of adsorbed oxygen species from grain boundaries. All films maintained excellent optical transparency of 80-90% in the visible range. The optical bandgap exhibited a blue-shift from 3.365 eV to 3.624 eV due to the Burstein-Moss effect induced by the increased electron carrier concentration. These results confirmed that hydrogen atmosphere post-annealing is the most effective method for enhancing the electrical conductivity of ZnO:Al thin films while maintaining high optical transparency.

Nozzle-printing dispensers, which utilize air pulsation as a dispensing principle, operate by transmitting air pressure to the liquid to push a constant amount of liquid. Nozzle printers have the advantage of precisely controlling energy based on liquid properties, such as viscosity and surface tension, enabling the precise application of liquid at specific locations and quantities. This study introduces a printing process sequence using a nozzle printer equipped with a high-resolution vision alignment system. It compares printing patterns according to key process variables (jet pressure, tip height, and travel speed) that affect coating quality. Experimental results showed that a coating standard deviation of 2.14 μm was achieved at a moving speed of 20 mm/s and a nozzle height of 0.2 mm, resulting in the most stable and uniform coating quality. Through these experiments, optimal conditions were identified based on factors such as coating width, uniformity, and presence of discontinuity, and the effects of these conditions on the precision manufacturing process are discussed.

To ensure the long-term reliability of flexible photovoltaic (FPV) modules, it is crucial to develop an effective moisture barrier layer that prevents the infiltration of moisture and oxygen. We developed such a layer composed of parylene (700 nm) and AlOx (70 nm), optimizing its material properties, moisture-blocking performance, and processing conditions. The barrier layer applied to the Ethylene Tetrafluoroethylene (ETFE) substrate demonstrated a water vapor transmission rate (WVTR) of 6.33 × 10^-2 g/m²/day and an average visible light transmittance (AVT) of 85.3% over the 380-780 nm wavelength range. For the FPV module with this barrier, Damp/Heat (DH) reliability testing was conducted at 85℃ and 85% relative humidity for up to 1,000 hours. During testing, the power conversion efficiency (PCE) decreased slightly from 25.4% (0 hr) to 24.7% (1,000 hr), reflecting a minimal reduction of only 0.7%. The primary cause of degradation was identified as a -4% relative change in shortcircuit current density (JSC) before and after DH testing. Consequently, the ETFE/parylene/AlOx multilayer moisture barrier proved highly effective in ensuring the long-term reliability of solar modules.

Iron oxide nanoparticles (NPs) have gained significant attention for their broad applicability in biomedical imaging, soft robotics, and catalysis owing to their exceptional magnetic properties and biocompatibility. A key challenge in maximizing their functionality lies in achieving a uniform size distribution and dispersity, alongside strong interfacial affinity with the surrounding medium that are essential for optimizing magnetic behavior and processibility. In this study, we present a facile solvothermal synthesis of monodisperse iron oxide NPs with tunable size and controllable surface hydrophobicity by varying precursors, capping agents, and solvents. By varying these synthesis parameters, we demonstrate a clear correlation between NP size, dispersity, and key magnetic properties, including saturation magnetization (MS) and coercivity (HC). This advancement in synthesis methodology offers a reliable, efficient approach for producing high-quality iron oxide NPs, which makes possible for practical use of them across a range of technological and biomedical applications.

As the operating environment in semiconductor processes becomes demanding, research is being conducted to manufacture dense alumina substrates without defects after sintering to ensure high durability of electrostatic chucks, which are critical components in semiconductor equipment. Therefore, in this study, in order to manufacture green sheets with a high filling ratio for implementing a high-density substrate, alumina powders with average particle sizes of 2.07 μm (L) and 0.37 μm (S) were mixed in ratios of 9:1, 8:2, 7:3, and 6:4, respectively, and green sheets were manufactured and the filling ratio and sintering behavior were observed. Green sheets were fabricated by preparing a slurry using organic materials in Al₂O₃ powders of different particle sizes. The packing density of the green sheet mixed with L and S alumina powders with different average particle sizes in a ratio of 7:3 before and after binder burn-out showed the highest values of 3.19 g/cm³ and 2.87 g/cm³, respectively. As a result of observing the sintered density based on the mixing ratio of alumina powders revealed that the alumina sheet mixed at a 6:4 ratio of L and S powders, sintered at 1,700℃, exhibited the best sintering characteristics with a density of 3.96 g/cm³.

Memristors, as next-generation memory devices, have garnered significant academic interest. Among them, TiO₂/TiO_2-x based memristors have particularly attracted substantial scholarly attention. Research on the activation and stability of TiO2 based memristor devices through process parameters is essential. Here, to determine the impact of process parameters on the activation of TiO₂/TiO_2-x based memristor devices, we fabricated the memristor devices using a sputtering system andconducted annealing at 400℃. Additionally, to analyze the electrical characteristics of the devices, we measured the I-V curves and C-V curves. Also, we examined TiO₂/TiO_2-x based memristor devices surface using SEM. Consequently, it was observed that the devices subjected to annealing exhibited improved hysteresis curves in the I-V characteristics, a reduced bandgap, and changes in resistance compared to the non-annealed devices. The retention test results further demonstrated that the set/reset characteristics of the devices were stable, confirming their potential applicability as memory devices.

The transparent electrode characteristics of the SnO₂/AgNi/SnO₂ (OMO) multilayer structures prepared by sputtering were investigated according to the annealing temperature. Ni-doped Ag of various compositions was selected as the metal layer and heat treatment was performed at 100~300℃ to evaluate the thermal stability of the metals. The manufactured OMO multilayer structures were heat treated for 6 hours at 400~600℃ in an N₂ atmosphere. The structural, electrical, and optical properties of the OMO structures before and after annealing were evaluated and analyzed using a UV-VIS spectrophotometer, 4-point probe, XPS, FE-SEM, etc. OMO with Ni-doped Ag shows improved performance due to the reduction of structural defects of Ag during annealing, but OMO structure with pure Ag shows degradation characteristics due to Ag diffusion into the oxide layer during high-temperature annealing. The figure of merit (FOM) of SnO₂/Ag/SnO₂ was highest at room temperature and gradually decreased as the heat treatment temperature increased. On the other hand, the FOM value of SnO₂/AgNi/SnO₂ mostly showed its maximum value at high temperature(~550℃). In particular, the FOM value of SnO₂/Ag-Ni (3.2 at%)/SnO₂ was estimated to be approximately 2.38×10^-2 Ω^-1. Compared to transparent electrodes made of other similar materials, the FOM value of the SnO₂/Ag-Ni (3.2 at%)/SnO₂ multilayer structure is competitive and is expected to be used as an alternative transparent conductive electrode in various devices.

In this study, we fabricated single grain YBCO bulk superconductors with control of the distance between the seed and the upper surface of the YBCO compacts. The magnetic levitation force of the YBa₂Cu₃O₇ superconducting bulk, which corresponds to the energy amount of the superconducting bulk, was measured to be 32.634 N at the center of the bulk where the seed was placed. Under field cooling conditions, a capture magnetic force of 2.17 kG was observed at the center of the bulk. The trapped magnetic force curve corresponding to the stability of the superconducting bulk means that the superconducting specimens were well grown in the form of single grains.

The Microplotter system with a fluid dispensing method, sprays fluid based on ultrasonic pumping through piezoelectric devices. This technique can possible for various materials with a wide range of viscosities to be printed in microscale. In this paper, we introduces dispenser printing technology as well as aim to understand and apply various processes using the equipment. In addition, we will explain how to optimize the equipment by adjusting parameters such as spray intensity, tip height during printing, and patterning speed. By utilizing Microplotter’s advantage of being compatible with a wide range of fluids, including metal nanoparticles, carbon nanotubes, DNA, and proteins, it is expected to be used in various fields such as printed electronics, biotechnology, and chemical engineering.

In this study, Iron (III) oxide-hydroxide (δ-FeOOH) was successfully synthesized using hydrogen peroxide (H₂O₂) as an oxidizing agent. The synthesis of δ-FeOOH was carried out by controlling the amount of H₂O₂, and pure δ-FeOOH was successfully synthesized in ranges from 0.2 mL to 0.6 mL of H₂O₂. The size of the synthesized δ-FeOOH particles was compared by controlling the amount of oxidant H₂O₂. The average particle size of the synthesized pure δ-FeOOH particles increased from 875.1 nm to 897.2 nm as the amount of H₂O₂ was increased. The optical properties of δ-FeOOH synthesized under these specific conditions were investigated. All δ-FeOOH showed a similar trend of increasing and decreasing light absorption from 800 nm to 400 nm, although there was a slight difference in the amount of light absorption, with the largest amount of light absorption at 410 nm. The band gap energy of δ-FeOOH through the Tauc plot method was about 2.1~2.2 eV when H₂O₂ was 0.2~1.4 mL. With a sufficient small particle size, simple control of that particle size, and a small band gap energy enough to absorb light in the visible spectrum, δ-FeOOH could be useful in a variety of applications, including photoelectrochemistry and battery electrodes.

This paper presents the development and market trends of nano biosensors. These biosensors must possess high sensitivity and selectivity to effectively detect diseases. Presently, many research groups are focusing on the field-effect transistor aspect of nano biosensors, which can identify diseases such as Down syndrome, bladder cancer, breast cancer, and numerous other cancers, utilizing graphene and transition metal dichalcogenide materials. In the case of in-vitro diagnostics, the use of nano biosensors has been rapidly growing since the onset of the COVID-19 pandemic. This paper also discusses market trends and the outlook for both national and international enterprises engaged in the nano biosensor field. Nano biosensors are expected to play a beneficial and significant role soon, contributing to the early diagnosis of diseases and subsequently improving patient outcomes.

Recently, active research has been conducted to enhance the power characteristics and thermal stability of lithiumion batteries (LiBs) by modifying separators using a ceramic coating method. However, since the thermal properties and surface features of the separator vary depending on the characteristics of the ceramic powders applied to the separator, it is crucial to manufacture ceramic powders optimized for the separator’s performance. In this study, we evaluated the characteristics of three types of α-alumina (A-1, A-2, and A-3) produced with varying dispersant contents and milling times, in addition to commercial α-alumina (AES-11). Subsequently, the optimized powders (A-3) were coated onto the separator using an aqueous binder for comparison with the characteristics of an AES-11 coated separator and an uncoated PE separator. The A-3 coated separator improved electrolyte wettability with a low contact angle (44.69°) and increased puncture strength (538 gf). Furthermore, it exhibited excellent thermal stability, with a shrinkage value of 5.64% when exposed to 140℃ for 1 hour, compared to the AES- 11 coated separator (6.09%) and the bare PE separator (69.64%).

In this paper, a 1,200 V Si-based IGBT used in electric vehicles and new energy industries was designed. A field stop IGBT with a separate gate structure, which is the proposed structure, was designed to change trench depth and split gate width variables. Then, the general trench structure and electrical characteristics were compared and analyzed. As a result of conducting the trench depth experiment, it was confirmed that the breakdown voltage was the highest at 6 μm, and the on-state voltage drop was the lowest at 3.5 μm. In the separate gate width experiment, it was confirmed that the breakdown voltage decreased as the variable increased, and the on-state voltage drop increased. Therefore, it may be seen that it is preferable not to change the width of the separate gate. In addition, experiments show that there is no difference in on-state voltage drop compared to a structure in which a general field stop structure has a separate gate structure. In other words, it is determined that adding a dummy gate with a separate gate structure to the active cell will significantly improve the on-voltage drop characteristics, while confirming that the on-voltage drop does not change, and while having excellent characteristics in terms of breakdown voltage.

Nickel oxide is a nonstoichiometric transparent conductive oxide with p-type conductivity, a wide-band energy gap of 3.4~4.0 eV, and excellent chemical stability, making it a very important candidate as a material for bipolar devices.P-type conductivity in Transparent Conductive Oxides (TCO) is controlled by the oxygen vacancy concentration. During the TCO film deposition process, additional oxygen diffusing into the NiO structure causes the formation of Ni 3p ions and Ni vacancies. This eventually affects the hole concentration of the p-type oxide thin film. In this work, the surface morphology and the electrical characteristics were confirmed in accordance with the annealing atmosphere of the nickel oxide thin film.

The deposition of indium zinc oxide (IZO) thin films was carried out on substrate at room temperature by RF magnetron sputtering. The effects of substrate temperature, RF power and deposition pressure were investigated with respect to physical and optical properties of films such as deposition rate, electrical properties, structure, and transmittance. As the RF power increases, the resistivity gradually decreases, and the transmittance slightly decreases. For the variation of deposition pressure, the resistivity greatly increases, and the transmittance is decreased with increasing deposition pressure. As a result, it was demonstrated that an IZO film with the resistivity of 3.89 × 10^-4 Ω·cm, the hole mobility of 51.28 ㎠/Vs, and the light transmittance of 86.89% in the visible spectrum at room temperature can be prepared without post-deposition annealing.

Cast-resin transformers are widely installed in various electrical power systems because of their low operating cost and low influence on external environmental factors. However, when they have an internal defect during the manufacturing process or operation, a partial discharge (PD) occurs, and eventually destroys the insulation. In this paper, a Rogowski-type PD sensor was studied to replace commercial PD sensors used for the insulation diagnosis of power apparatus. The proposed PD sensor was manufactured with four different types of PCB-based winding structures, and it was analyzed in terms of the detection characteristics for standard calibration pulses and the changes of the output voltage according to the distance. The output increased linearly in accordance with the applied discharge amount. It was confirmed that the hexagon structure sensor had the highest sensitivity, because the winding cross-sectional area of the sensor was larger than others. In addition, as the distance from the defect increased, the output voltage of the sensors decreased by 7.32% on average. It was also confirmed that the attenuation rate according to the distance decreased as the input discharge amount increased. For the application of this new type sensor, PD electrode system was designed to simulate the void defect. Waveforms and PRPD patterns measured by the proposed PD sensors at DIV and 120% of DIV were the same as the results measured by MPD 600 based on IEC 60270. The proposed PD sensors can be installed on the inner wall of the transformer tank by coating its surfaces with a non-conductive material; therefore, it is possible to detect internal defects more effectively at a closer distance from the defect than the conventional sensors.

Recently, piezoelectric devices, such as ultrasonic surgery, ultrasonic atomizer, and ultrasonic speaker, are analyzed and designed by finite element simulation methods. However, the discrepancy between the design and the experiment results of the device typically occurs due to the inaccuracy of the piezoelectric material properties. To improve the simulation accuracy, the material properties of the PZT ceramics were better refined using parameter estimation method. The material parameters are elastic stiffness c^E_ij and piezoelectric constant e_ij of PZT ceramics. The impedance curve characteristics for the LTE mode of PZT ceramics were calculated. The mismatch between the simulation and the experimental data were compared and minimized by a least square method. Finally, the simulated impedance data were compared with the experimental data for the various vibration modes of PZT ceramics and the optimized material properties of PZT ceramics were verified. To further verify the accuracy, this method was also applied to piezoelectric PMN-PT single crystals.

Laser-induced plasmonic sintering of metal nanoparticles (NPs) is a promising technology to fabricate flexible conducting electrodes, since it provides instantaneous, simple, and scalable manufacturing strategies without requiring costly facilities and complex processes. However, the metal NPs are quite expensive because complicated synthesis procedures are needed to achieve long-term reliability with regard to chemical deterioration and NP aggregation. Herein, we report laser-induced Ag NP self-generation and sequential sintering process based on low-cost Ag organometallic material for demonstrating highquality microelectrodes. Upon the irradiation of laser with 532 nm wavelength, pre-baked Ag organometallic film coated on a transparent polyimide substrate was transformed into a high-performance Ag conductor (resistivity of 2.2 × 10^-4 Ω·cm). To verify the practical usefulness of the technology, we successfully demonstrated a wearable transparent heater by using Ag-mesh transparent electrodes, which exhibited a high transmittance of 80% and low sheet resistance of 7 Ω/square.

Magnetoelectric (ME) properties of 3-0 type particulate composites have been investigated with respect to application features for reliable magnetic sensitivity and magnetically-induced output voltage. In order to figure out the magnetoelectric characteristics in the ME composites, frequency dependent ME responses were studied from [0.948 Na0.5K0.5NbO3-0.052 LiSbO₃]-[Co_1-xZn_xFe₂O₄] (NKNLS)/Co_1-xZn_xFe₂O₄ (CZFO, x=0, 0.1, and 0.2). As a result, the maximal αME of 23.15 mV/cm·Oe was achieved from the NKNLS-CZFO (x_Zn = 0.1) composites at resonance frequency of 315 kHz and H_dc = 0 Oe. From the frequency dependent ME responses, it is clearly described that the self-biased ME composites can be used for applications as both magnetic sensors and energy harvesters, respectively.

This paper describes why we must use graphene materials for solar cells and biosensors. It has been superior in several properties such as super-thin film, higher tensile strength, high current density, high thermal conductivity, and high mobility. Therefore, graphene is one of the emerging advanced materials because of its applicability in various electronic device applications. We investigated the requirements of graphene materials for the application of solar cells and biosensors. In addition, we discussed the research trends such as transducers in biosensors and transparent electrodes in solar cells. The research on graphene materials and their application will be beneficial and helpful for the near future.

In this study, we investigated the optical, electrical and exothermic characteristics of ITO/Ag/ITO multilayer structures prepared with various Ag thicknesses on quartz and PI substrates. The transparent conducting properties of the ITO/Ag/ITO multilayer films depended on the thickness of the mid-layer metal film. The ITO/Ag (14 nm)/ITO showed the highest Haccke’s figure of merit (FOM) of approximately 19.3×10^-3 Ω^-1. In addition, the exothermic property depended on the substrate. For an applied voltage of 3.7 V, the ITO/Ag (14 nm)/ITO multilayers on quartz and PI substrates were heated up to 110℃ and 200℃, respectively. The bending tests demonstrated a comparable flexibility of the ITO/Ag/IT multilayer to other transparent electrodes, indicating the potential of ITO/Ag/ITO multilayer as a flexible transparent conducting heater.

Lithium-ion batteries (LIBs) have become a main energy storage device in various applications, such as portable appliances, renewable energy facilities, and electric vehicles. However, the poor thermal stability of LIBs may cause explosion or fire. The thermal runaway is the result of a failure of the separator inside LIB. Damages like tearing, piercing, and collapsing of the separator were simulated in a mechanical, an electrical, and a thermal way, and small discharge pulses of a few mV were detected at the time of separator damages. From the experimental results, this paper provided a method that can identify the separator failure before thermal runaway in the aspect of a potential explosion and fire prevention measures.

In this study, composite transparent electrodes were fabricated either from a conductive polymer poly(3,4- ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT:PSS) or silver nanowire (AgNW). Three transparent electrodes such as PEDOT:PSS, PEDOT:PSS and AgNW mixture, and AgNW were fabricated. As for a transparent electrode, measured sheet resistance values were 89.6, 60.6 and 28.6 Ω/sq, and the transmittance values were 80.2, 82.0 and 83.8% while surface roughness (Rq) values were 4.1, 8.1, 20.4 nm for PEDOT:PSS, PEDOT:PSS and AgNW mixture, and AgNW, respectively. To verify the overall performance of these composite electrodes, we applied these electrodes to the top electrode of the solution-processed organic solar cells (OSCs). PEDOT:PSS provided the best performance with a fill factor (FF) of 51.2% and a photoconversion efficiency (PCE) of 2.2%, while traditional metal top electrode OSC provided FF of 60.5% and PCE of 3.1%.

For electronic paper displays using electrophoresis, the response time and reflectivity of the image panel fabricated by filtering are analyzed. For the filtering process, a square wave and ramp wave are applied to white charged particles with a unique q/m value. We divide the sample panels into #1 to #4 according to the applied waveform in the filtering process. Step waves comprising two steps are used to drive the panel; therefore, we divide the driving conditions into D1~D4. The applied voltage at the first stage of the half cycle of the driving waveform moves the charged particles attached via the image force from the electrode, and the applied voltage at the second stage moves the floating charged particles by detaching. As mentioned, four types of driving conditions (D1 to D4) classified according to the half cycle of the driving waveform are applied to the samples #1 to #4), which are classified according to four types of filtering process. When driving condition D1 is applied to the four types of sample panels, the rise time of #1 is 1.59s, #2 is 1.706s, #3 is 1.853s, and #4 is 1.235s, resulting in #4 being relatively faster compared with other sample panels, and showing the same trend in other driving conditions. As a result, we confirm that applying the driving condition D1 causes abrupt movement of the white charged particles injected into the cell. When the same driving waveform (D1) is applied to each sample, reflectivities of 32.1% for #1, 31.4% for #2, 27.9% for #3, and 63.4% for #4 are measured. From the experiment, we confirm that the driving condition D1 (1s of 3.5 V, 9s of 3.0 V) and ramp wave #4 in filtering are desirable for good reflectivity and response time. Our research is expected to contribute to the improvement of the filtering process and optimization of the driving waveform.

This study reports the fabrication and application of semitransparent Cu nanoparticle layers. Spin coating and subsequent drying of a Cu colloid solution were performed to deposit Cu nanoparticle layers onto Si and glass substrates. As the spin speed of the spin coating increases, the density of the nanoparticles on the substrate decreases, and the agglomeration of nanoparticles is suppressed. This microstructural variation affects the optical properties of the nanoparticle layers. The transmittance and reflectance of the Cu nanoparticle layers increase with increasing spin speed, which results from the trade-off between the exposed substrate area and surface coverage of the Cu nanoparticles. Since the glass substrates coated with Cu nanoparticle layers are semitransparent and colored, it is anticipated that the application of a Cu nanoparticle-dielectric bilayer structure to transparent solar cells will improve the cell efficiency as well as aesthetic appearance.

Sulphur hexafluoride (SF6) is mostly used as a current-insulating medium in gas-insulated switchgears (GIS), owing to its excellent dielectric strength and arc-extinguishing performance. The global warming potential (GWP) of SF6, however, is 23,900 times that of CO₂, and its life time in the atmosphere is 3,200 years. For these reasons, new eco-friendly gases to replace SF6 are required. In this study, the partial discharge (PD) characteristics of green gas for grid (g³) and dry air (N₂/O₂) were analyzed to compare with those of SF₆. A PD electrode system was designed to simulate the protrusion defect in GISs and fabricated for experimentation. To compare the PD characteristics of each gas, the discharge inception voltage (DIV), discharge extinction voltage (DEV), discharge magnitude, discharge pulse number, and phase pattern were analyzed. Results from this study are expected to provide fundamental materials for the design of eco-friendly GISs.