GaN nanowire (NW)-based hybrid structures have attracted attention for optoelectronic applications due to their high surface area and efficient carrier transport. However, the optical transparency of GaN NWs is often limited by unintended residual species accumulated on the surface and in the inter-wire regions, as well as defect-related absorption, leading to reduced light transmission. In this work, we demonstrate that thermal annealing significantly improves the optical transparency of GaN NWs grown on indium tin oxide (ITO)/glass substrates. The transmittance increased from 47.9% to 78.5% at 550 nm after rapid thermal annealing at 800^oC for 3 min, while a comparable value (~75.5%) was achieved at 600^oC for 5 min. PbBr₃ was deposited onto the GaN NWs to form hybrid structures, and temperature-dependent photoluminescence (TDPL) measurements revealed enhanced emission stability with suppressed peak shift and reduced spectral broadening. Arrhenius analysis based on a two-channel model revealed that the activation energy of the dominant non-radiative recombination pathway increased from 62 meV in the as-grown sample to 85 meV after thermal annealing, while its relative contribution remained nearly unchanged. In contrast, the shallow trap-assisted pathway exhibited a similar activation energy of approximately 6 meV in both samples, but its contribution decreased from 0.35 to 0.17 after annealing. As a result, the internal quantum efficiency (IQE) improved from 75.9% to 87.4%. These results show that thermal annealing improves optical transparency by removing residuals and suppresses defect-related recombination, leading to enhanced carrier dynamics and improved optical performance of PbBr₃-based hybrid structures.

This study investigates the effects of chemical etching for anti-glare (AG) treatment and the subsequent deposition of a TiZrO₂/SiO₂ double-layer anti-reflection (AR) coating on glass surfaces. The AG treatment was performed using ammonium fluoride in gel form via screen printing, followed by electron beam deposition of SiO₂/TiZrO₂ layers. The surface roughness, optical transmittance, and refractive index were analyzed. The results revealed that while the surface roughness increased with larger screen patterns during the AG treatment, it was reduced by the deposition of the AR layers. Additionally, the gloss caused by external light was higher with lower surface roughness, but it was effectively reduced by the AR coating. The optical reflectance showed minimal changes during the AG treatment, remaining similar to that of bare glass substrates. However, the AR coating significantly decreased reflectance. The combination of AG treatment and AR coating improved optical transmittance and reduced gloss, making this method beneficial for enhancing visibility in automotive displays. The findings suggest that this approach can mitigate the impact of external light and improve the clarity of displayed information, making it suitable for automotive display applications.

In this study, Iron (III) oxide-hydroxide (δ-FeOOH) was successfully synthesized using hydrogen peroxide (H₂O₂) as an oxidizing agent. The synthesis of δ-FeOOH was carried out by controlling the amount of H₂O₂, and pure δ-FeOOH was successfully synthesized in ranges from 0.2 mL to 0.6 mL of H₂O₂. The size of the synthesized δ-FeOOH particles was compared by controlling the amount of oxidant H₂O₂. The average particle size of the synthesized pure δ-FeOOH particles increased from 875.1 nm to 897.2 nm as the amount of H₂O₂ was increased. The optical properties of δ-FeOOH synthesized under these specific conditions were investigated. All δ-FeOOH showed a similar trend of increasing and decreasing light absorption from 800 nm to 400 nm, although there was a slight difference in the amount of light absorption, with the largest amount of light absorption at 410 nm. The band gap energy of δ-FeOOH through the Tauc plot method was about 2.1~2.2 eV when H₂O₂ was 0.2~1.4 mL. With a sufficient small particle size, simple control of that particle size, and a small band gap energy enough to absorb light in the visible spectrum, δ-FeOOH could be useful in a variety of applications, including photoelectrochemistry and battery electrodes.

In this study, we successfully synthesized copper oxide (Cu₂O) particles through a hydrothermal method at a relatively low temperature (150℃). The synthesis involved the precise control of molar concentrations of NaOH. Notably, Cu₂O particles were effectively synthesized when NaOH concentrations of 0.15 M and 0.20 M were utilized. While attempts were made at different molar concentrations, the synthesis of pure Cu₂O particles was only achieved at concentrations of 0.15 M and 0.20 M. In this experimental investigation, Cu₂O synthesized under these specific conditions exhibited absorption characteristics within the wavelength range of 640 to 570 nm, consistently exhibiting a band gap energy of 1.9 eV. These Cu₂O particles, characterized by their small band gap energy and straightforward synthetic method, hold significant promise for various applications including semiconductors and solar cells.

Calcium fluoride (CaF₂) single crystal is applied to numerous industrial applications, especially for optical uses. To have excellent optical transmission properties, however, CaF₂ crystals should be carefully fabricated through liquid-phase crystal growth techniques. In this study, as one of the early stage research activities to grow CaF₂ crystals with a good transmittance at the ultraviolet wavelength range, computational thermodynamic models were provided to deepen the understanding of the crystal growing processes of CaF₂ under various conditions. To remove point defects and oxygen impurities in the grown CaF₂ crystals, the system was thermodynamically evaluated to get optimal process conditions. From the reviews of previous experimental studies, computational thermodynamic approaches were found to be an effective and powerful tool to understand the meaning of the crystal growth processes and to obtain optimal process conditions.

The field of liquid crystal display (LCD) is constantly in the spotlight and the process of depositing an alignment layer in the LCD manufacturing process is very important to obtain excellent performance such as low-power driving and high-speed response to improve LCD performance. Therefore, research on liquid crystal (LC) alignment is being actively conducted. When manufacturing LCD, it is necessary to consider the effect of the alignment layer thickness as one of the factors affecting various LCD performances. In addition, previous studies confirmed the LC alignment characteristics correlate with the rotation speed in the spin coating process. Therefore, the electro-optical properties of the LCD were investigated by manufacturing a polyimide alignment layer by varying the rotation speed in the spin coating process in this study. It was confirmed that the thickness of the polyimide alignment layer was controlled according to the spin coating conditions. The average transmittances of anti-parallel LC cells at the spin coating speed of 2,500 rpm and 3,000 rpm are about 60%, which indicates that the LC cell has relatively higher performance. At the spin coating speed of 3,000 rpm, the voltage-transmittance curve of twisted nematic (TN) LC cell was below 1.5 V, which means that the TN LC cell operated at a low power. In addition, high-speed operating characteristics were confirmed with a response time of less than 30 ms. From these derived data, we confirmed that the ideal spin coating speed is 3,000 rpm. And these results provide an optimized polyimide alignment layer process when considering enhanced future LCD manufacturing.

In this work, we synthesized alloy-core InZnP quantum dots, which are more efficient than single-core InP quantum dots, using a solution process method. The effect of synthesis conditions of alloy core on optical properties was investigated. We also investigated the conditions that make up the gradient shell to minimize defects caused by lattice mismatch between the InZnP core and ZnS is 7.7%. The stable synthesis temperature of the InZnP alloy core was 200℃. Quantum dots consisting of three layered ZnSe gradient shell and single layered ZnS exhibited the best optical property. The properties of quantum dots synthesized in 100 ml and in 2,000 ml flasks were almost equal.

With the advent of the IoT (internet of things) era, there has been discussion on how to efficiently use various information from daily life. In academic and industrial society, various smart devices such as smart watches, smart phones, and smart glasses have been developed and commercialized for narrowing the physical/psychological distance with user information. According to recent developments of smart devices, the contemporary people have desired to check their body information and treat disease by themselves. According to the needs of the time, biological researches by phototherapy/monitoring have been actively conducted. Among various light sources, microLEDs have been spotlighted due to their superior optoelectric properties and stability. In this paper, we would like to review the state-of-the research results on the next-generation biological therapy devices via microLEDs.

We have proposed a novel planar lightwave circuit (PLC) optical sensor to monitor the contamination in a flow-cell where water is continuously supplied through a water quality measurement system. We designed a PLC chip with a V-shape waveguide and the simulated its function as a sensor for monitoring contamination in a flow-cell using a numerical the FDTD (finite-difference time-domain) analysis. A novel cross type of waveguide was introduced to make the PLC chip of the V-shaped waveguide. The fabricated PLC was cut into the cross waveguide. A change in the optical propagation loss of the PLC sensor was observed after immersing the PLC sensor into city water. It was determined that the propagation loss of the PLC sensor was 3 dB at a wavelength of 1.55 μm in the city water for 15 days.

It was proven that the light outputs of blue GaN-based light-emitting diodes (LEDs) was seriously influenced by the application of external stress. We have simulated the wave function overlap of an electron and hole, which are significantly reduced by the development of stress. Consequently, its internal quantum efficiency decreased from 67.0% to 37.5%. To experimentally investigate the effect of stress, we designed and prepared a special zig system. By applying external tensile stress to compensate for the compressive stress innately developed in Blue LEDs, it was found that the optical output was greatly enhanced from 83.1 mcd to 117.2 mcd at a current of 100 mA, an increase of approximately 41%. In contrast, when the compressive stress is developed more by external compressive stress, we observed that the light output power was reduced from 89.0 mcd to 80.7 mcd, a decrease of approximately 9.3%.

In this paper, the ZnS nanoparticles were synthesized according to the process conditions of hydrothermal synthesis. When the molar ratio of Zn to S was 1:1.2, it was confirmed that it had a cubic single phase and a high crystal phase. After the molar ratio is fixed, hydrothermal synthesis was conducted at 180℃ for 24, 36, 72 and 96 h in order to confirm the structural change with the change of hydrothermal synthesis times. As the hydrothermal synthesis times increased, the particle size increased. The hydrothermal synthesized particle size for 72 h was considered to be suitable for sintering. The ZnS ceramic had a density of 99.7% and an excellent transmittance of ~70% in the long-wavelength region.

SiGe thin films were deposited by remote plasma enhanced chemical vapor deposition (RPE-CVD) at 400℃ using SiH₄ or SiCl₄ and GeCl₄ as the source of Si and Ge, respectively. The growth rate and the degree of crystallinity of the fabricated films were characterized by scanning electron microscopy and Raman analysis, respectively. The optical and electrical properties of SiGe films fabricated using SiCl₄ and SiH₄ source were comparatively studied. SiGe films deposited using SiCl₄ source showed a lower growth rate and higher crystallinity than those deposited using SiH4 source. Ultraviolet and visible spectroscopy measurement showed that the optical band gap of SiGe is in the range of 0.88~1.22 eV.

The ratio of the period of a diffractive element to the input beam size is a critical parameter in a diffractive beam shaper. We measured and calculated the Fraunhofer diffraction patterns of a periodic hologram with an input beam size similar to the period of the hologram. The measured intensities show very complicated patterns and are strongly dependent upon the center position of the laser beam relative to the hologram. Using a diffraction formula for a periodic hologram, we calculated the diffracted light intensities and fit them to the measured ones. The measured and calculated intensities are in good agreement even when the beam diameter of the incident laser is similar to the period of the hologram. We can therefore use this formula to estimate the output of a periodic beam shaper even under such an extreme condition.

We prepared ZnS thin films via chemical bath deposition (CBD) in an aqueous solution of ammonia (NH₃) and hydrazine (N₂H₄). The composition ratio of hydrazine used was 0%, 17%, 22%, 29%, or 50%. We investigated the effects of hydrazine and ammonia on the growth, and the structural and optical properties of ZnS in terms of surface uniformity, voids, and grain size. We found that during the growth of ZnS films, hydrazine was very effective for improving the surface morphology and layer uniformity with fast layer formation, while it had no effect on the bandgap energy, Eg.

We have proposed a hydrogen detection sensor based on a Pd (palladium)-coated, single-mode, optical fiber. The experimental results demonstrated that the sensor could detect hydrogen in air as well as in insulation oil. The influence of Pd film thickness and environmental temperature on response time and sensitivity was analyzed. The reflected optical power at the optical-fiber/Pd interface decreased as the concentration of hydrogen increased, in both air and the insulation oil. The sensor showed 0.75 dB of optical power variation when the concentration of dissolved hydrogen was saturated in the insulation oil.

Terahertz time-domain spectroscopy has been used to study the optical properties of Pr³⁺-doped selenide glasses. The complex refractive indexes of Pr³⁺-selenide glasses were measured in a frequency range from 0.3 to 1.5 THz. The real and imaginary refractive indexes increased with increasing frequency and Pr³⁺ ion concentration. The obtained result indicated that the phonon modes of the Pr³⁺-doped selenide glasses shift to lower frequencies with the concentration of Pr³⁺ ions. The theory of far-infrared absorption in amorphous materials was used to analyze the results. The measured data showed that the disorder-induced terahertz absorption increased with increasing Pr³⁺ ion concentration.

Zinc sulphide (ZnS) nanoparticles were fabricated by hydrothermal synthesis at 180℃ for 12 h. Two kinds of ZnS powder (hydrothermal synthesized ZnS and commercial ZnS) were investigated by X-ray diffraction (XRD) and scanning electron microscopy (SEM) for phase and microstructure, respectively. The XRD patterns showed that all ZnS nanoparticles have a sphalerite (cubic) structure. The nanoparticles of two different ZnS powders were sintered by spark plasma sintering. The sintered ZnS were analyzed by XRD, SEM, and FT-IR. We found that the transmittance of the infrared region is highly dependent on the density and crystal structure of sintered ZnS and the purity of the starting ZnS powder.

We fabricated 1-D and 2-D diffraction gratings of SiOx anti-reflection (AR) film grown on a quartz substrate and integrated them into a c-Si photovoltaic (PV) submodule. The light-trapping effect of the resulting submodules was studied in terms of the oblique optical incident angle, θ_i. As the θ_i increased, solar conversion efficiency, η, was improved as expected by the increased optical transmission caused by the grating. For θ_i≤30°, the relative solar conversion efficiency, Δη, of a 1-D SiOx (t=300 nm) grating, compared to that of a flat SiOx AR-coated integrated PV submodule, was improved very little, with a small variation of within 2%, but increased markedly for θ_i≥40°. We observed a change of Δη as large as 10.7% and 9.5% for the SiOx grating of period t=800 nm and 1200 nm, respectively. For a 2-D SiOx (t=300 nm) grating integrated PV submodule, however, the optical trapping behavior was similar in terms of θ_i but its variation was small, within ±1.0%.

TeO_x thin films were deposited at various O₂/Ar gas-flow ratios by a reactive RFmagneton sputtering technique from TeO₂ and Te targets. X-ray diffraction (XRD) results revealed that the TeO_x thin films were amorphous. The structure and chemical composition of the TeO_x thin films were investigated by fourier transform infrared spectroscopy (FT-IR) and X-ray photoelectron spectroscopy (XPS). The optical characteristics of the TeO_x thin films were investigated by an Ellipsometer and a UV-VIS-NIR spectrophotometer. According to the O₂/Ar gas-flow ratios, the atomic composition ratio of TeO_x thin films was divided into two regions(x=1-2, 2-3). Different optical characteristics were shown in each region. With an increasing O₂/Ar gas-flow ratio, the refractive index of the TeO_x thin films decreased and the optical bandgap of the films increased.

In this paper, the IES file was measured by applying a secondary optical lens to a 21 W LED engine, and the lighting calculation software RELUX was used to perform simulations with the data file of this measurement. For two-lane (two way) concrete paved roads, six LED engine are applied to each streetlight and simulation results show that Uo (uniformity) 0.56, UI (longitudinal uniformity) 0.86 and TI (threshold iIncrement) 9% which satisfies the required standards. RELUX was also used to LED streetlights by designing them in three dimensions, that is ±25% of the arm length of 2.8 m standardized by the road lighting standards of the Korea Expressway Corporation. Comparative analysis was carried out on adjustments were made in increments of 0.1 m that Uo, UI, and TI values in the range of arm lengths from 2.1 m∼3.5 m. For the arm length range of 2.1 m∼2.4 m, Uo was high, whereas UI was low. Therefore, we present the optimal light distribution values designed for an arm length of 2.5 m.

To provide the clear images from the direct light on electrical board and display devices, anti glare treatment of display cover glass is needed. In this study, the effects of surface treatment temperature, concentration, and etching solution coating thickness of the gel phase on optical elements control such as gloss, haze of reflected light and transmittance, were investigated. Cover glasses were treated at different coating thickness and additive concentration. The optical properties were examined using spectrophotometer, gloss and haze meter. The surface morphology and roughness were measured by the optical microscope and Ra measuring instrument. The etching rate and surface morphologies were dramatically affected by the concentration of acid additive in the viscous gel because of re-crystallization of components in the etching solution, hydrogel formation and coagulant after coating on glass substrate. In our experimental range, cover glass which is surface-treated with various optical properties as well as the morphology uniformity was obtained; in particular, optical properties could be controlled by etching solution coating thickness of the gel phase and the concentration of additive. The gloss was depended on the surface roughness and it showed the linear relationship between optical transmittance and haze of reflected light, respectively.

Road lighting has emerged in importance as an essential system to secure safety and visibility for drivers and pedestrians. According to the Road Lighting Standards (KS A 3701), the luminance uniformity (U0) should be 0.4, the luminance uniformity for lanes (UI) should be 0.5, and a threshold increment (TI) of 10% should be satisfied. In this study, we conducted simulations using the Relux program in which the secondary optical lens was applied to a 21 W engine. Ten LED engines were installed on a two-way four-lane road, and the simulation result satisfied the requirements with U0 0.47, UI 0.63 and TI 8%. The U0, UI, and TI were compared with the angle of the LED streetlight varied in the range of 9° ~ 15° with 0.5° intervals. The range was selected as ± 25% of the standard inclination angle of 12° according to the Road Lighting Standard. The U0 was high and the UI and TI were low when the tilting angle was in the range of 9.5° ~ 10.5°. Consequently, an optimum-design of lighting distribution was obtained for the concrete two-way four-lane road when the inclination angle was 9°.

In this study, the change of optical characteristics was studied according to the micro optical pattern provided by photo lithography followed by thermal reflow process. The shape and luminance variation with micro pattern was evaluated by SEM and spectrometers. Also, we analyzed the luminance characteristics using the 3D-optical simulation (Optis works) program. As a result, we found that the radius of curvature(R) in micro pattern is decreased up to 77%(150℃) compared to the radius of curvature at the condition 100℃, which is caused by efficient reflow of organic material without chemical changes. The highest enhancement of brightness with optimum micro pattern was obtained at the condition of 120℃ reflow process. The brightness gain with optical micro patterns is more than 15% at the condition of R=16.95 um, θ =77.14° compared to original optical source. The results of light simulation with various radius of curvature and side angle of pattern shows the similar result of experiment evaluation of light behavior on optical micro patterns. It is regarded that the more effect on light enhancement was contributed by side angle which is effective factor on light reflection, rather than the curvature of micro-patterns.

The object of this paper is to develop optimal optical filter, which can be used to identify thefinancial account and read the information. The five factors which affect the performance of the opticalfilter are identified as optical glass type, existence of Fe, Photo pic coating type, and coating form. Inthis study we seek to determine the optimal combination for the best design of the optical filter. For eachcombination, the performances of optical filter are investigated using the proper experimental equipmentsand methods. White-state voltage, black-state voltage, and black-state error rate are used for theperformance measures. Through the statistical analysis of the performance data collected, we havedetermined the optimal design of the optical filter.

In this paper, we have researched semiconductor optical filters to solve the problem of the high failure rate that are recognize bad of financial account, jam of financial account and the ATM service interruption due to failure of accurate location information among the operation of the ATM (automatic teller machine) systems. A semiconductor optical filters that have high resolution and less diffuse, high transmittance are able to detect the information of financial account surface accurately. Therefore, it is a stable filter that is able to minimize the incidence of disability. In this paper, we drew the determinants by element for implement an excellent semiconductor optical filters. Based on this, we had to be able to implement the semiconductor optical filter that is able to be mounted on the actual ATM system through future studies.

In order to develop a LED luminaire for naval-submarines which can replace a conventional one with two-compact fluorescent lamp (CFL) of 18 W, we analyzed the electrical and optical performance of the conventional luminaire. A LED luminaire was fabricated as compact as possible based on the analyzed data. The weight of the prototype LED luminaire is 1.8 kg, reducing up to 58% of the conventional one. The use of LED package for the submarine luminaire could reduce the power consumption from 38 W to 14.5 W with the same optical performance. The reason is that the optical efficacy of the LED luminaire improved by 2.47 times as 61.9 lm/W, compared to 25.1 lm/W for the conventional one.

An optical model is proposed in the white LED using phosphor and LED chip. In this paper a new model that describes the absorption rate and quantum efficiency with increasing the mixing ratio of phosphor in silicone, and the allotment of the phosphor absorption optical power in the several phosphor mixing in the silicone. Single phosphor in silicone from the optical measurement data before and after molding, the solution to get the blue optical power and the phosphor emission optical power is proposed. By these solution the absorption rate and the quantum efficiency was obtained. The model with single phosphor mixing in the silicone the validity was confirmed.

Recently, micro cavity is studied to reduce the optical loss of BLU and OLED. In this paper, we suggest applying micro cavity to photo-luminescent lamp with plasma discharge technology to meet the display applications for a BLU for LCD. The structure of photo-luminescent lamp consists of SUS foil and ITO glass with micro cavity. The op to-elect riccharacteristics of photo-luminescent lamp with micro cavity was evaluated. The brightness of photo-luminescent device was increased over 111 ccVm2 with the adaptation of patterned micro cavity at 30 pm. The 3D optical simulation verified the enhanced light out coupling when micro cavity applied to the device.

(Ga203)x(ZnO)100-x, (GZO) films were prepared at room temperature by using a facing target sputtering (FTS) system and their electrical resistivites was investigated as a function of the Ga203 content. The GZO film with an atomic ratio of Ga203 of x 7 wt. %, shows the lowest resistivity of 7.5 X 10-4 cm. The GZO films were also prepared at various substrate temperatures from room temperature to 300t, and their electrical resistivity was found to be improved as the substrate temperature was increased, A very low resistivity of 2.8x 10u1 n that is almost comparable with that of ITO film was obtained in the GZO films prepared at the substrate temperature of 300t by using the FTS.

Mg doped zinc tin oxide (ZTOMg) thin films were prepared on glasses by rf magnetron sputtering. O was introduced into the chamber during the sputtering. The optical properties of the films as a function of oxygen flow rate were studied. The crystal structure, elementary properties, and depth profiles of the films were investigated by X-ray diffraction (XRD), x-ray photoelectron spectroscopy (XPS), and secondary ion mass spectrometry (SIMS), respectively. Bottom-gate trdnsparent thin film transistors were fabricated on N Si wafers, and the variation of mobility, threshold voltage etc. with the oxygen flow rate were observed.

Citations

• A Study on the Chemical Properties of AZO with Crystal Structure and IGZO of Amorphous Structure Due to the Annealing Temperature
  Young Ho So, Jung Ho Song, Dong Myung Seo, Teresa Oh
  Industry Promotion Research.2016; 1(1): 1.     CrossRef