Multilayer ceramic batteries (MLCBs) have attracted increasing attention as compact all-solid-state energy-storage devices that can be manufactured using multilayer ceramic processing technologies. In this study, an MLCC-compatible fabrication process for oxide-based MLCBs was developed using Li₁₊ₓAlₓTi₂₋ₓ(PO₄)₃ (LATP) solid electrolytes, Li₃V₂(PO₄)₃ (LVP) cathodes, and Cu current collectors. Commercial LATP powders were evaluated in terms of particle-size distribution, phase purity, thermal stability, and ionic conductivity. The selected LATP powder was subsequently employed for tape-cast green-sheet fabrication, and the effects of polyvinyl butyral (PVB) binder content on slurry rheology and sheet microstructure were investigated. An optimized binder composition containing 11 wt% PVB (BM-2/BH-3 = 3:7) provided improved processability and microstructural uniformity. Drying conditions during sequential electrode printing were also optimized to suppress sheet warpage and improve multilayer registration. Thermogravimetric and differential thermal analyses (TG–DTA) were used to establish an optimized two-step debinding and co-firing process under a controlled reducing atmosphere. The resulting multilayer structures exhibited uniform densification without significant blistering, delamination, or interfacial defects. Charge–discharge measurements confirmed that electrochemical functionality was retained after the complete manufacturing process, yielding a discharge capacity of approximately 2.5–2.7 μAh.

Renewable energy harvesting technologies, which convert ambient resources such as wind into electrical energy, have attracted significant attention as sustainable power sources for self-powered systems. However, the long-term applicability of wind energy harvesters in remote or extreme environments has not yet been fully discussed, particularly in terms of structural robustness and environmental adaptability. In this study, we designed a double-clamped flutter-type triboelectric generator (DFTEG) for efficient wind energy harvesting and evaluated its output performance under various simulated outdoor conditions. The DFTEG features a modular acrylic frame with a magnet-based assembly for easy maintenance and film replacement, utilizing PTFE films and aluminum electrodes to maximize the charge density difference according to the triboelectric series. Structural optimization revealed that a single-film configuration with a length of 110 mm produced the most stable flutter vibration and a large effective contact area, achieving a maximum open-circuit voltage of 42.28 V and a short-circuit current of 2.89 μA. Furthermore, performance evaluations under various environmental variables, including relative humidity, temperature, and sand particles interference, confirmed consistent electrical output across diverse environmental conditions. These results demonstrate the potential of the proposed DFTEG as an environmentadaptive independent power source capable of stable operation under complex environmental factors.

The development of a large-area solution process for CuO nanowires, which are promising p-type thin film transistors (TFT) channel materials, is required. To overcome the limitations of the existing high-vacuum and high-cost deposition process, a large-area Cu nanowire network was formed on the substrate using the Mayer rod coating method, and a CuO channel was implemented by subsequent thermal annealing. Consequently, p-type TFT with an on/off current ratio of 1.4×10⁴ and a field-effect mobility µ_FE≈10^-4 cm²/(V⋅s). was fabricated and optimized. X-ray diffraction (XRD) and X-ray photoelectron spectroscopy (XPS) analyses showed that the sample annealed at 200°C exhibited an incomplete oxidation state with a mixed Cu/Cu₂O phase and a high fraction of M-OH species (58.78%), resulting in a low on/off current ratio (≈1.2). In contrast, annealing at 450°C leads to a CuOdominant phase, where the fraction of lattice oxygen(O1) increases to 31.11% and the oxygen vacancy (VO) component increases to 7.15%, indicating a significant improvement in hole concentration and charge transport. These phase transitions and surface chemical changes are identified as the key mechanisms for the enhanced TFT switching characteristics. The low-cost, large-area Mayer rodbased solution process proposed in this study provides a basic process platform for p-type TFTs applicable to flexible wearables and display technologies and suggests the possibility of commercialization through additional optimization of bias stability in the future.

GaN nanowire (NW)-based hybrid structures have attracted attention for optoelectronic applications due to their high surface area and efficient carrier transport. However, the optical transparency of GaN NWs is often limited by unintended residual species accumulated on the surface and in the inter-wire regions, as well as defect-related absorption, leading to reduced light transmission. In this work, we demonstrate that thermal annealing significantly improves the optical transparency of GaN NWs grown on indium tin oxide (ITO)/glass substrates. The transmittance increased from 47.9% to 78.5% at 550 nm after rapid thermal annealing at 800^oC for 3 min, while a comparable value (~75.5%) was achieved at 600^oC for 5 min. PbBr₃ was deposited onto the GaN NWs to form hybrid structures, and temperature-dependent photoluminescence (TDPL) measurements revealed enhanced emission stability with suppressed peak shift and reduced spectral broadening. Arrhenius analysis based on a two-channel model revealed that the activation energy of the dominant non-radiative recombination pathway increased from 62 meV in the as-grown sample to 85 meV after thermal annealing, while its relative contribution remained nearly unchanged. In contrast, the shallow trap-assisted pathway exhibited a similar activation energy of approximately 6 meV in both samples, but its contribution decreased from 0.35 to 0.17 after annealing. As a result, the internal quantum efficiency (IQE) improved from 75.9% to 87.4%. These results show that thermal annealing improves optical transparency by removing residuals and suppresses defect-related recombination, leading to enhanced carrier dynamics and improved optical performance of PbBr₃-based hybrid structures.

This paper proposes a circular sequential lighting control method to reduce current imbalance and luminance deviation among multiple LED modules in AC-powered LED lighting systems. Conventional fixed-sequence lighting control repeatedly prioritizes the same LED modules in every rectified voltage cycle, which leads to unequal current distribution, luminance non-uniformity, and the accelerated degradation of specific modules during long-term operation. To address these limitations, a circular sequential lighting strategy is introduced, in which the lighting order is cyclically rotated at every rectified cycle, ensuring that all LED modules experience equal lighting opportunities. A prototype AC-LED lighting system consisting of four series-connected LED modules was implemented and experimentally evaluated. The results demonstrate that, while the conventional fixed-sequence method produces a maximum average current deviation of up to 1.6 mA among modules, the proposed method equalizes the average current across all modules to approximately 17.1 mA. Furthermore, the flicker index remains at 0.13, which is comparable to that of the conventional method, indicating that luminance uniformity is improved without degradation of optical performance. The proposed circular sequential lighting control effectively distributes electrical stress, enhances luminance uniformity, and improves long-term reliability, making it a practical and efficient solution for high-quality AC-LED lighting applications.

β-Ga₂O₃ is an ultra-wide bandgap semiconductor promising for high-power electronic applications; however, heteroepitaxial growth on sapphire is challenging lattice and symmetry mismatch. In this study, β-Ga₂O₃ thin films were grown on C-plane sapphire substrates with various off-axis angles (0–12°) using mist-CVD, and the influence of substrate miscut on structural and optical properties was investigated. All films grown at 900°C exhibited (-201) oriented β phase. The crystal quality was strongly dependent on the off-axis angle, with intermediate off-axis angles (Δ_a = 6–8°) showing the narrowest rocking curve width. Off-axis substrates promoted step-aligned growth behavior compared to on-axis growth. Optical measurements revealed enhanced transmittance and wider bandgap values (4.92–4.95 eV) for off-axis samples compared to the on-axis film (4.69 eV). The findings provide practical guidelines for optimizing heteroepitaxial β-Ga₂O₃ growth on low-cost sapphire substrates for high-performance device applications.

This review introduces Corning’s Ribbon Ceramic process and the broader idea of ribbon ceramics―continuous, ultra-thin ceramic sheets made by tape or slot-die casting and fast, continuous sintering―covering key materials such as Al₂O₃, YSZ/ScSZ, PZT, LLZO, and LCO. Motivated by the need for scalable, energy-efficient ceramic components for electrification (green-hydrogen SOECs), next-generation Li-metal batteries, and compact piezo devices, we summarize capabilities and use cases using only publicly available information. Our main contribution is a clear platform view: continuous roll-to-roll conveyance with minutes-scale firing produces fully dense, fine-grained, high-purity ceramics at ~10-100 μm thickness with smooth native surfaces and controlled shapes, delivered as long rolls (up to ~300 ft), panels (~100 mm wide), or narrow strips (~0.5 mm). Illustrative results include 20-40 μm 3YSZ electrolytes for SOECs (high oxygen-ion conductance, ~1 GPa bend strength), LLZO garnet separators that cycle at 25℃ with interlayers, and free-standing LCO cathode ribbons tunable from dense to ~30% porous. For piezo acoustics, 60-80 μm PZT sheets (d33 ~300 pC/N) enable fine metallization and on-screen speakers, while fast firing reduces volatile loss and yields smaller grains. Together, these advances point to high-volume, lower-footprint manufacturing and faster adoption of novel ceramic membranes and substrates in SOEC/green-hydrogen systems, solid-state or hybrid lithium batteries, RF/power electronics, and piezo applications.

Silicon carbide (SiC) MOSFETs provide superior performance compared to traditional silicon devices under hightemperature and high-power conditions, making them particularly valuable for power electronics applications requiring highfrequency switching and high-energy efficiency. As the electric vehicle (EV) market expands, these devices are commonly packaged into six-pack modules, which can show their different electrical characteristics between the bare-die device and the package due to packaging that improves heat dissipation and other properties. This study uses bare-die SiC MOSFETs to explore their intrinsic characteristics and evaluate their performance in a half-bridge configuration. A half-bridge circuit was constructed, and performance was assessed by varying driving frequencies (10 kHz and 50 kHz) and adjusting the duty cycle between 20% and 80%. Analysis revealed that, at a fixed switching frequency, the average output voltage and average output current are proportional to the duty cycle.

The quench behavior of wires for superconducting fault current limiters at DC faults was simulated, with a focus on the effect of capacitor discharge on the quench. The behavior was also expressed in mathematical forms to facilitate a better understanding of the simulation results and for rough analytical estimations of the wire length suitable for the circuit voltage and capacitance. The quench resistance development behavior for various wire lengths and circuit capacitances was simulated using the model developed in the previous work. The quench behavior was expressed in mathematical forms, reflecting the concept of heat balance. During the quench, the wire temperature increased more slowly for longer wires, but was found to increase in a similar pattern. The wire length estimated by the mathematical formula was close to the one obtained by the simulation, with an error range of a few %. The calculations will be used to estimate effectively the length of wires needed to build superconducting fault current limiters for applications in DC power systems.

The continuous rise of atmospheric carbon dioxide (CO₂) emissions highlights the urgent need for sustainable air purification technologies. Current Direct Air Capture (DAC) filters often rely on toxic amines, which limit long-term stability and safe application. Here, we report a non-toxic PAN-based nanofiber air filter fabricated by electrospinning and urea-assisted carbonization. Structural analyses confirmed the introduction of nitrogen functionalities that enhanced CO₂ affinity, while SEM and FT-IR revealed graphitic carbon formation. In air-chamber tests, the optimized carbonized nanofiber reduced CO₂ concentration from 25,000 ppm to 2,000 ppm, a level generally regarded as acceptable for indoor environments, while simultaneously removing over 95% of PM₁₀, PM_2.5, and PM_0.1 particulates. This dual functionality, combined with facile fabrication and material safety, demonstrates strong potential for PAN-derived carbon nanofiber membranes in DAC systems and eco-friendly air purification devices. These findings suggest a viable pathway toward scalable, sustainable air-filter technologies for carbon-neutral applications.

Nozzle-printing dispensers, which utilize air pulsation as a dispensing principle, operate by transmitting air pressure to the liquid to push a constant amount of liquid. Nozzle printers have the advantage of precisely controlling energy based on liquid properties, such as viscosity and surface tension, enabling the precise application of liquid at specific locations and quantities. This study introduces a printing process sequence using a nozzle printer equipped with a high-resolution vision alignment system. It compares printing patterns according to key process variables (jet pressure, tip height, and travel speed) that affect coating quality. Experimental results showed that a coating standard deviation of 2.14 μm was achieved at a moving speed of 20 mm/s and a nozzle height of 0.2 mm, resulting in the most stable and uniform coating quality. Through these experiments, optimal conditions were identified based on factors such as coating width, uniformity, and presence of discontinuity, and the effects of these conditions on the precision manufacturing process are discussed.

Citations

• Flexible piezoelectric cross-bar array sensors for upper-limb kinesthetic sensing via muscle dynamics
  Junki Lee, Jihun Choi, Hyunseung Kim, Min Gon Son, Dong Yeol Hyeon, Jung Hwan Park, Andris Šutka, Chang Kyu Jeong
  Journal of the Korean Ceramic Society.2026;[Epub]     CrossRef

With the advancement of the information society, the demand for highly integrated and multi-functional electronic devices is rapidly increasing. To meet these demands, high-performance transistors with low power consumption, high-speed operating, and mechanical flexibility are essential. Among various candidates, semiconducting single-walled carbon nanotubes (s-SWCNT)-based transistors, which exhibit intrinsically ambipolar characteristics, have emerged as promising components for CMOS-like circuits. In this study, s-SWCNT were selectively dispersed using rr-P3DDT, a thiophene-based conjugated polymer, and filed-effect transistors (FETs) were fabricated by inducting directional alignment for enhanced charge transport through an off-centered spin-coating process. The electrical characteristics of the fabricated s-SWCNT FETs were evaluated under various thermal annealing conditions (100℃, 150℃, 200℃, and 250℃). Off-centered spin-coated and high temperature annealed s- SWCNT FETs exhibited high field-effect mobilities over 5 cm²/Vs in both p-type and n-type operation, along with ideal Vshaped ambipolar transfer curves. These results indicate a significant enhancement in ambipolar performance due to efficient desorption of residual oxygen and water molecules in active channel via high temperature annealing. Furthermore, CMOS-like inverter circuits demonstrated an ideal inversion voltage (VIN = V_DD/2) and a high voltage gain of approximately 9.5. These findings highlight the potential of SWCNT-based materials for realizing next-generation flexible electronic circuits that combine high-performance, energy efficiency, and simplified solution-processing.

Metal halide perovskite materials have emerged as promising candidates for next-generation optoelectronic applications owing to their outstanding optical properties and tunable emission characteristics. However, their practical application is hindered by poor environmental stability, especially under conditions of heat, moisture, and UV exposure, necessitating effective encapsulation strategies. This review summarizes recent progress in enhancing the environmental stability of perovskite nanocrystals through polymer matrix embedding, inorganic oxide encapsulation, and compositionally matched core-shell structures using homogenous perovskite derivatives. We discuss how polymers enhance the environmental and moisture stability of perovskite nanocrystals, how oxide-based shells (e.g., SiO₂, TiO₂) contribute to thermal robustness and barrier protection, and how homostructural core-shells provide lattice-matched defect passivation with improved long-term durability. A comprehensive understanding of the advantages and limitations of each encapsulation strategy, along with their rational integration, can accelerate the commercialization of perovskite-based technologies in various applications such as highcolor- purity displays, color conversion filters, and flexible optoelectronic devices.

SMD-type 660 nm wavelength semiconductor laser diode device is fabricated using silicon resin molding technology and fabricated a BT resin printed circuit board. BT resin electrode structure printed circuit boards with soldering electrode pads and through holes for heat dissipation were fabricated. The SMD process is an injection molding technique in which the chip is molded from silicon material and then cut by a dicing process to complete the beam emission surface. The fabricated SMD-type semiconductor laser diode exhibits a good near-field beam pattern with no scattering/dispersion caused by the printed circuit board or silicon molding in the emitted laser beam, or reflections around the chip. It was also confirmed that the heat generated at 20 mA operation has good heat dissipation characteristics through the through-hole heat dissipation structure.

Citations

• Mitigating Contact‐Constricted Thermal Bottlenecks by Magnetically Programmable hBN Bridge Fillers in Al2O3/Epoxy Composites
  Yeonwook Jeong, Sabina Ghorsaine, Chan‐Jae Lee, In Kim, Mooho Lee, Hyejeong Lee, Ginam Kim, Jong‐Woong Kim
  Small.2026;[Epub]     CrossRef

Recently, oxide semiconductors have assumed a pivotal role in electronic displays and transparent electronic devices such as amorphous indium gallium zinc oxide (a-IGZO), characterized by high electron mobility and excellent stability. a- IGZO is very suitable for next-generation applications such as flexible displays because it is possible to manufacture highperformance transistors even at low temperatures. However, since the electrical properties tend to deteriorate in hightemperature environments, research aimed at improving thermal stability is needed. In this study, a low-temperature plasma annealing process was introduced to improve the high-temperature stability of the a-IGZO thin film. This process enhances electron mobility by reducing defects in the a-IGZO film and provides stable device performance even under high-temperature conditions. As a result of the experiments of 5 min, 10 min, 15 min, and 20 min, the a-IGZO TFT, which was subjected to plasma annealing at 160℃ for 5 min, showed the best electrical performance, especially in charge mobility and current-voltage characteristics. The technical potential for improving the performance of a-IGZO-based display device was emphasized, and the foundation for applying this power generation to flexible displays and next-generation electronic devices was laid. Future research will focus on determining the optimal annealing conditions by exploring various temperature ranges and plasma parameters to integrate these results into the actual device manufacturing process. These efforts are expected advance significantly to advancing next-generation high-performance display technology.

This paper presents a comparative analysis of the fire detection characteristics between conventional fire detector sensors and an Si-based color sensor. With the rapid industrial development in modern society, the concentration of urban populations and the expansion of building sizes have accelerated, leading to an increased frequency of large-scale fires. As a result, the importance of fire detection technologies has been emphasized. However, conventional detectors continue to experience issues such as false alarms and malfunctions. To address these challenges, a novel fire detection technology utilizing an Si-based color sensor, which is effective for fire detection, is proposed. To evaluate the fire detection performance of each sensor, a fire detection test apparatus was developed, and experiments were conducted separately under smoke and flame conditions to analyze the fire detection capabilities of the Si-based color sensor, temperature sensor, and flame detection sensor. The experimental results demonstrated that detection speed and sensor values varied depending on the type of combustible material. Specifically, in the smoke and flame tests, the Si-based color sensor detected fires 26.7 and 43.7 seconds faster than the temperature sensor, and 26.6 and 15.4 seconds faster than the flame detection sensor, respectively. Therefore, it was confirmed that the Si-based color sensor proposed in this study is an effective detection technology that is expected to provide improved performance compared to conventional fire detectors.

Iron oxide nanoparticles (NPs) have gained significant attention for their broad applicability in biomedical imaging, soft robotics, and catalysis owing to their exceptional magnetic properties and biocompatibility. A key challenge in maximizing their functionality lies in achieving a uniform size distribution and dispersity, alongside strong interfacial affinity with the surrounding medium that are essential for optimizing magnetic behavior and processibility. In this study, we present a facile solvothermal synthesis of monodisperse iron oxide NPs with tunable size and controllable surface hydrophobicity by varying precursors, capping agents, and solvents. By varying these synthesis parameters, we demonstrate a clear correlation between NP size, dispersity, and key magnetic properties, including saturation magnetization (MS) and coercivity (HC). This advancement in synthesis methodology offers a reliable, efficient approach for producing high-quality iron oxide NPs, which makes possible for practical use of them across a range of technological and biomedical applications.

Citations

• Magnetically Directed Percolation Networks in Polydopamine-Mediated Carbon Nanotube/Fe₃O₄ Nanocomposites
  Dongyeong Gim, Hyeokju Kwon, Minjeong Ha
  Journal of Electrical and Electronic Materials.2026; 39(3): 288.     CrossRef

The search for sustainable and efficient energy conversion technologies is becoming increasingly critical in response to global energy and environmental challenges. Traditional lead-based piezoelectric materials, such as lead zirconate titanate (PZT), have high piezoelectric constant but present significant health problems and environmental risks due to their hazardous metal contaminants. This study addresses these concerns by investigating barium titanate (BTO), a lead-free alternative, and enhancing its performance using anisotropic nanowires (NWs) structures. BTO NWs were synthesized via a two-step hydrothermal method and incorporated into a poly(vinylidene fluoride-trifluoroethylene) [P(VDF-TrFE)] matrix to fabricate a piezoelectric composite film. The resulting device demonstrated a notable increase in electrical output compared to devices based on isotropic morphology of BTO nanoparticles, exhibiting enhanced performance. These findings suggest that BTO NWs hold significant promise for applications in flexible and wearable electronics, paving the way for further advancements in sustainable energy technology.

Citations

• Interphase engineering in carbon black–reinforced piezoelectric nanocomposites: A combined experimental and micromechanical modeling study
  Ziwen Zhao, Masoumeh Khamehchi, Mohammad J. Mahmoodi, Zhenjin Wang, Fumio Narita
  Materials & Design.2026; 268: 116391.     CrossRef
• MXene-reinforced ultrasensitive piezoelectric pressure sensors based on P(VDF-TrFE) nanofibers with hybrid nanofillers
  Jingyi Yang, Jianqiao Wang, Zike Guo, Shuai Liu, Yaohua Dong, Peng Zhou, Tianjin Zhang, Yajun Qi
  Journal of Alloys and Compounds.2026; 1079: 189867.     CrossRef
• Layer-engineered BNBT–polymer films for multifunctional applications
  M. Vijatovic Petrovic, A. Dzunuzovic, J. Bobic, Z. Despotovic, F. Cordero, E. Mercadelli, Z. Radovanovic, F. Craciun
  Journal of Alloys and Compounds.2026; 1079: 189972.     CrossRef
• Piezoionic sensor devices of integrated gradient electrolyte gels
  Yi Fang, Hongbing Li, Taeuk Eom, Chang Kyu Jeong, Yong Zhang
  Chemical Engineering Journal.2026; 540: 177542.     CrossRef
• Interfacial polarization triggered by low-k fillers boosts piezoelectricity of MMT/PT composites for intelligent health monitoring
  Yong Ao, Junjun Yuan, Wenqi Yu, Rui Yuan, Boling Lan, Shenglong Wang, Tingting Zhou, Guicen Liu, Wei Zhao, Zhiyuan Gao, Xiaofei Jiang, Weili Deng, Long Jin, Weiqing Yang
  Journal of Materials Chemistry A.2026; 14(57): 39367.     CrossRef
• Interfacial Engineering of Composite Piezoelectric Fibers Via an Anchor-Chain Architecture
  Jun Liu, Qiao Zhou, Pengcheng Zhang, Shuying Hu, Fang Zhou, Shuangshuang Ren, Ting Guo, Leiying Miao
  ACS Applied Engineering Materials.2026; 4(8): 4367.     CrossRef
• High-output droplet driven-based triboelectric nanogenerator for integrated electrothermal energy conversion
  Pengfei Wang, Di Yang, Nannan Wang, Jie Meng, Lanyue Cui, Weixiang Sun, Daoai Wang
  Journal of Environmental Chemical Engineering.2026; 14(5): 125134.     CrossRef
• Strain-insensitive static and dynamic pressure sensing in a piezoionic hydrogel under 200% stretching
  Prisca Putri Elesta, Epsita Kar, Jinhwan Yoon
  Nano Energy.2026; 159: 112469.     CrossRef
• Interfacially programmed co-assembly of multimodal piezoelectric polymer foams via balanced amphiphilicity for adaptive self-powered electronics
  Menghui Wang, Huihui Li, Wenyue Wang, Tianyu Zheng, Chenchen Wu, Donghai Qiu, Bo Lu, Binbin Dong, Chuntai Liu, Changyu Shen
  Nano Energy.2026; 159: 112430.     CrossRef
• Recent advances in piezoelectric energy harvesting: materials, configurations, optimization techniques, and emerging applications
  Mir Waqas Alam, Sohail Ahmad Parah, Farooq Ahmad Dar, Abdulrahman Aljasim, Chawki Awada, Rameez Ahmad Parra
  Journal of Materials Science: Materials in Electronics.2026;[Epub]     CrossRef
• Flexible piezoelectric sensing based on a microcolumn-to-microcolumn architecture of BNKT-ST/P(VDF-TrFE) composite
  Guiyun Gao, Tong Pan, Panpan Lv, Wentao Yang, Shuzhi Zhang, Hang Zhan, Cuncheng Li, Luchao Ren, Jin Qian, Mingwei Zhang
  Ceramics International.2026;[Epub]     CrossRef

One method to increase the output of solar modules is the application of the Half-cut technique, which requires a scribing process involving direct irradiation of infrared lasers on the solar cells. During this process, the laser melts the surface of the solar cells at high temperatures, enabling mechanical division, but this can lead to output loss due to thermal degradation caused by the laser. To minimize such losses, a low-temperature and low-loss division method has been devised. In this study, we compared the electrical characteristics and leakage currents affecting output degradation between the newly devised low temperature and low-loss cell division method and the conventional laser division method. Additionally, we conducted a 3-point flexural test to evaluate the mechanical properties of both methods.

The display industry has recently been at the forefront of innovative advancements in modern electronic devices. Technological progress such as flexible display holds significant potential across various application fields, particularly in wearable devices and rollable displays. A low-temperature process is essential for fabricating such displays. One of the key technologies in displays is the thin film transistor (TFT), with amorphous indium gallium zinc oxide (a-IGZO) receiving particular attention. a-IGZO is widely applied in high-performance displays due to its high charge mobility and stability. While a thermal treatment above 350℃ is typically required to maximize the electrical performance of a-IGZO TFTs, such high temperatures pose challenges for utilizing polymer substrates like plastics. Here, we thesis investigates the simultaneous lowtemperature plasma annealing process to develop next-generation high-performance flexible display devices. To define the optimal temperature, devices were fabricated and analyzed at varying temperatures of 40℃, 80℃, 120℃, and 160℃. Experimental results indicated that devices fabricated at 160℃ and 80℃ exhibited superior performance, with those at 160℃ demonstrating better performance in terms of current ratio, threshold voltage, and subthreshold swing. These findings confirm that the simultaneous low-temperature plasma annealing process is effective for next-generation high-performance displays.

MBB (multi-busbar) technology is a module technology to achieve high power, and the use of a number of thin circular metal wires increases light-receiving capacity and reduces resistance. In the process of interconnection using a wire, the stress of the cell increases depending on the degree of coupling between the wire and the cell and the degree of damage caused by heat, or the mobility of current decreases due to poor bonding. The degree of such loss is affected by IR lamp, hot plate temperature and wire thickness. In addition, the values of contact resistance were compared and analyzed to analyze the cause of the decrease in electrical characteristics. In this study, process condition optimization was carried out through peeling test, SEM analysis, EL test, and pre/post bonding efficiency characteristic analysis of the bonded cell according to process conditions, compared the contact resistance.

Piezoelectricity refers to the phenomenon where mechanical stress is converted into electrical signals or, conversely, electrical signals are converted into mechanical stress. Ferroelectric materials, characterized by high dielectric permittivity and spontaneous polarization, retain their polarization even after the removal of an electric field. In such materials, poling plays a crucial role in enhancing the piezoelectric effect, with the process of aligning dipoles being known as poling. This review focuses on studies that have compared and analyzed the enhancement of piezoelectric properties in ceramics and polymers through two representative poling methods: AC poling (ACP) and DC poling (DCP). Even within the same category of ceramics or polymers, variations in piezoelectric properties are observed based on the material type, poling method, and poling conditions. Under certain conditions, ACP has been shown to provide superior poling effects compared to DCP. Through this review, we propose that ACP has the potential not only to replace the traditionally used DCP in the poling of piezoelectric materials but also to serve as a more effective method. This could spark increased interest in the study of poling methods for piezoelectric polymers, a field that has received relatively less attention.

Citations

• Research Progress of Candidate Vibration Measurement Ceramic Materials and Intelligent Cutting Tools
  Zhenrong Sun, Chuanzhen Huang, Hanlian Liu, Zhenyu Shi, Dun Liu, Zhen Wang, Longhua Xu, Shuiquan Huang
  Journal of the American Ceramic Society.2026;[Epub]     CrossRef

Precise control over the morphology of nanostructures is critical for tailoring their physical and chemical properties. This study addresses the challenge of developing a simple, integrated method for synthesizing both 1D and 2D colloidal Cu nanostructures in a single system, achieving successful tuning of their localized surface plasmon resonance (LSPR) properties. A facile hydrothermal synthesis utilizing potassium iodide (KI) and hexadecylamine (HDA) is presented for controlling Cu nanostructure morphologies. The key to achieving 1D nanowires (NWs) and 2D nanoplates (NPs) depends on the controlled adsorption of HDA molecules and iodide (I-) ions on specific crystal facets. Depending on the morphologies, the resultant Cu nanostructures exhibit tunable LSPR peaks from 558 nm [nanoplates (NPs)] to 590 nm [nanowires (NWs)]. These results pave the way for the scalable and cost-effective production of plasmonic Cu nanostructures with tunable optical properties, holding promise for applications in sensing, catalysis, and photonic devices.

Citations

• Complexation-controlled Cu@Ag core-shell flakes for thermally stable printed electrodes in flexible energy-storage capacitors
  Seokhwan Kim, Geumseong Lee, Ye Chan Lee, Je-Hui Koo, Seonhwa Park, Geon-Tae Hwang, Mahesh Peddigari, Jungho Ryu, Dahye Shin, Kyoung Jin Jung, Kwi-Il Park, Yuho Min
  Chemical Engineering Journal.2026; 540: 177341.     CrossRef

Climate conditions, especially transport and storage, are a very important factor in the process of sampling and testing insulation oil in the field. The samples of insulating oil exposed to the atmosphere affect the dielectric strength, total acid number and moisture test value by oxygen and high humidity environment and may also affect the results according to the criteria specified in each test. Therefore, reliable test values for insulating oil testing require consideration of the atmospheric environment of the test site, including oxygen and humidity. In this paper, each test was conducted on insulating oil exposed to various time and humidity environments, and the effect of the atmospheric environment on the test results was analyzed by comparing and analyzing with the first insulating oil.

Due to changes in the form factor of display panels and touch screen panels in various devices, capacitive touch systems have evolved to address various issues such as low power consumption, noise immunity, and small chip size. Furthermore, some devices have applications that use a stylus. Since the stylus operates similarly to a finger touch, it encounters similar issues. Recent research trends focus on addressing key issues such as noise, which is primarily caused by the self-capacitor formed between the display cathode and the touch screen panel. In this paper, Various research papers discussing methods to eliminate external noise will be reviewed. These advancements enhance noise immunity in touch systems, making it easier to use thinner and more flexible panels. These progress make touch technology more versatile and reliable in various applications.

This study proposes an innovative methodology for developing flexible printed circuit boards (FPCBs) capable of conforming to three-dimensional shapes, meeting the increasing demand for electronic circuits in diverse and complex product designs. By integrating a traditional flat plate-based fabrication process with a subsequent three-dimensional thermal deformation technique, we have successfully demonstrated an FPCB that maintains stable electrical characteristics despite significant shape deformations. Using a modified polyimide substrate along with Ag flake-based conductive ink, we identified optimized process variables that enable substrate thermal deformation at lower temperatures (~130℃) and enhance the stretchability of the conductive ink (ε ~30%). The application of this novel FPCB in a prototype 3D-shaped sensor device, incorporating photosensors and temperature sensors, illustrates its potential for creating multifunctional, shape-adaptable electronic devices. The sensor can detect external light sources and measure ambient temperature, demonstrating stable operation even after transitioning from a planar to a three-dimensional configuration. This research lays the foundation for next-generation FPCBs that can be seamlessly integrated into various products, ushering in a new era of electronic device design and functionality.

An irradiator is developed using two UVA wavelength ranges of SMD LEDs as a curing light source. This module has dimensions of 545×111×300 mm³ and is equipped with a TIR bar-shaped lens made of PDMS silicone resin. The developed irradiator offers high uniformity, with 89% in the centerline of the horizontal axis direction, for two different wavelength ranges of 365 nm and 385 nm. The radiation intensity from the light source module shows highly directional characteristics, and the irradiator provides a maximum irradiance of 1,634 mW/cm² at a working distance of 50 mm. During the initial 5 minutes of operation, the irradiance experiences a rapid decrease. However, this issue is addressed by optimizing the LED’s current reduction characteristics and managing the Transistor’s temperature rise in the constant current circuit. After continuous operation for approximately 60 minutes. The highest temperature, near the central part of the irradiating surface, reaches 69.7℃, while the lowest temperature, near the edges, is 41.1℃.

This paper is an experimental study on the improvement of smoke and flame detection from different materials with YOLO. For the study, images of fires occurring in various materials were collected through an open dataset, and experiments were conducted by changing the main factors affecting the performance of the fire object detection model, such as the bounding box, polygon, and data augmentation of the collected image open dataset during data preprocessing. To evaluate the model performance, we calculated the values of precision, recall, F1Score, mAP, and FPS for each condition, and compared the performance of each model based on these values. We also analyzed the changes in model performance due to the data preprocessing method to derive the conditions that have the greatest impact on improving the performance of the fire object detection model. The experimental results showed that for the fire object detection model using the YOLOv5s6.0 model, data augmentation that can change the color of the flame, such as saturation, brightness, and exposure, is most effective in improving the performance of the fire object detection model. The real-time fire object detection model developed in this study can be applied to equipment such as existing CCTV, and it is believed that it can contribute to minimizing fire damage by enabling early detection of fires occurring in various materials.

Aluminum-induced crystallization (AIC) as a route to reduce the fabrication cost and to obtain polycrystalline Si (p- Si) thin-film of large grain size is a promising alternative of single-crystalline (s-Si) substrate or p-Si thin-film obtained by conventional methods such as solid phase crystallization (SPC) and laser-induced crystallization (LIC). As the AIC process occurs at the interface between a-Si and Al thin-films, there are various process and interface parameters. Also, it directly means that there is a certain parametric window to obtain p-Si of large grain size having uniform crystal orientation. In this article, we investigate the effect of the various process and interface parameters to obtain p-Si of large grain size and uniform crystal orientation from the literature review. We also suggest the potential use of the p-Si as a virtual substrate for the growth of various compound semiconductors in a form of low-dimension as well as thin-film as a way for their monolithic integration on Si.

This paper is a study on the optimal microdroplet generation conditions in indirect charging electrostatic spraying. Unlike the direct charging method, which applies power to the nozzle, the indirect charging method applies power to the discharge electrode between the nozzle and the collection electrode. Therefore, an electrically simplified system can be obtained by minimizing the insulation part a stable spray pattern can be obtained with a wide spray angle, and a stable spray pattern can be obtained with a wide spray angle. To conduct the study, an indirect charging type electrostatic spray visualization system was constructed and the static characteristics of the microdroplets were analyzed through image processing of the spray shape of the microdroplets. The total number of microdroplets and the number of microdroplets per power consumption are confirmed according to the changes in the distance between the discharge electrode and the collection electrode, the flow rate, and the applied voltage, which affect the generation of microdroplets, and using this, the optimal generation conditions are derived and the corresponding microdroplet size distribution was analyzed. As a result of the experiment, it was confirmed that the optimal generation condition was at a flow rate of 15 to 20 mL/min and a voltage of -22.5 to -25 kV in terms of the number of microdroplets, and at a flow rate of 15 to 20 mL/min and a voltage of -20 kV in terms of energy consumption efficiency.