Polymer nanocomposites incorporating inorganic nanofillers have emerged as highly promising electromagnetic interference (EMI) shielding materials, combining mechanical compliance with robust conductive percolation networks. Carbon nanotubes (CNTs) are particularly attractive as conductive fillers because their high aspect ratio facilitates percolation at low loadings. Also, CNTs offer superior mechanical durability under deformation compared to rigid, fracture-prone metal nanowires. For EMI shielding, high electrical conductivity is critical as it enhances both reflection and absorption through efficient charge dissipation and conduction losses. However, achieving highly aligned conductive pathways without degrading the intrinsic electrical properties of CNTs remains a significant challenge. Here, we demonstrate a non-destructive magnetic surface-functionalization and alignment strategy. Using a polydopamine (PDA)-mediated route, pristine multiwalled CNTs are uniformly decorated with Fe₃O₄ nanoparticles (FMWCNTs). This enables highly effective magnetic field-driven alignment at fields as low as 10 mT, promoting the strategic formation of percolation networks. By optimizing the Fe₃O₄/MWCNT ratio for high saturation magnetization and uniform coverage, the aligned FMWCNTs exhibit significant electrical anisotropy, delivering a 10.7-fold higher electrical conductivity in the parallel configuration compared to the vertical configuration. These findings present a scalable, room-temperature platform for engineering directionally enhanced conductivity in polymer nanocomposites, with broad applicability in advanced EMI shielding, flexible electronics, and advanced packaging technologies.

Citations

• Interfacial Engineering of Composite Piezoelectric Fibers Via an Anchor-Chain Architecture
  Jun Liu, Qiao Zhou, Pengcheng Zhang, Shuying Hu, Fang Zhou, Shuangshuang Ren, Ting Guo, Leiying Miao
  ACS Applied Engineering Materials.2026; 4(8): 4367.     CrossRef

The continuous rise of atmospheric carbon dioxide (CO₂) emissions highlights the urgent need for sustainable air purification technologies. Current Direct Air Capture (DAC) filters often rely on toxic amines, which limit long-term stability and safe application. Here, we report a non-toxic PAN-based nanofiber air filter fabricated by electrospinning and urea-assisted carbonization. Structural analyses confirmed the introduction of nitrogen functionalities that enhanced CO₂ affinity, while SEM and FT-IR revealed graphitic carbon formation. In air-chamber tests, the optimized carbonized nanofiber reduced CO₂ concentration from 25,000 ppm to 2,000 ppm, a level generally regarded as acceptable for indoor environments, while simultaneously removing over 95% of PM₁₀, PM_2.5, and PM_0.1 particulates. This dual functionality, combined with facile fabrication and material safety, demonstrates strong potential for PAN-derived carbon nanofiber membranes in DAC systems and eco-friendly air purification devices. These findings suggest a viable pathway toward scalable, sustainable air-filter technologies for carbon-neutral applications.

With the advancement of the information society, the demand for highly integrated and multi-functional electronic devices is rapidly increasing. To meet these demands, high-performance transistors with low power consumption, high-speed operating, and mechanical flexibility are essential. Among various candidates, semiconducting single-walled carbon nanotubes (s-SWCNT)-based transistors, which exhibit intrinsically ambipolar characteristics, have emerged as promising components for CMOS-like circuits. In this study, s-SWCNT were selectively dispersed using rr-P3DDT, a thiophene-based conjugated polymer, and filed-effect transistors (FETs) were fabricated by inducting directional alignment for enhanced charge transport through an off-centered spin-coating process. The electrical characteristics of the fabricated s-SWCNT FETs were evaluated under various thermal annealing conditions (100℃, 150℃, 200℃, and 250℃). Off-centered spin-coated and high temperature annealed s- SWCNT FETs exhibited high field-effect mobilities over 5 cm²/Vs in both p-type and n-type operation, along with ideal Vshaped ambipolar transfer curves. These results indicate a significant enhancement in ambipolar performance due to efficient desorption of residual oxygen and water molecules in active channel via high temperature annealing. Furthermore, CMOS-like inverter circuits demonstrated an ideal inversion voltage (VIN = V_DD/2) and a high voltage gain of approximately 9.5. These findings highlight the potential of SWCNT-based materials for realizing next-generation flexible electronic circuits that combine high-performance, energy efficiency, and simplified solution-processing.

The growing demand for miniaturized, lightweight, and sustainable electronic devices has intensified the need for advanced bonding materials. Existing electrically conductive adhesives (ECAs) often rely on high silver (Ag) content, resulting in elevated costs and environmental concerns. This study successfully developed a novel ECA with significantly reduced Ag content without compromising essential electrical conductivity and adhesion performance. Experimental results revealed that the optimized ECA demonstrates electrical conductivity comparable to that of commercial products, with notable advantages in cost reduction and eco-friendliness. These advancements position the developed ECA as a promising solution for next-generation electronic manufacturing, contributing to low-carbon technologies and sustainable practices. Future applications could further broaden its use across diverse electronic systems, driving progress in environmentally conscious technologies.

Energy harvesting technology offers an innovative solution for providing self-sustaining power to wearable and implantable electronic devices. However, traditional energy harvesters face limitations in operating within electrolytic environments or at low motion speeds. To overcome these challenges, a mechano-electrochemical energy harvester using carbon nanotubes has been developed. This technology relies on electrochemical ion movement to induce changes in electrochemical double-layer capacitance, enabling operation within electrolytes and optimizing performance at low deformation speeds. This environmentally friendly and sustainable energy solution is expected to play a crucial role in the advancement of future smart systems and wearable technologies.

Citations

• Fabrication and performance of integrated self-powered PAAM hydrogel flexible pressure sensors
  Huaikuan Zang, Chao Hu, Pan Niu, Yong Zhang
  Materials Science in Semiconductor Processing.2026; 214: 110899.     CrossRef
• Piezoionic sensor devices of integrated gradient electrolyte gels
  Yi Fang, Hongbing Li, Taeuk Eom, Chang Kyu Jeong, Yong Zhang
  Chemical Engineering Journal.2026; 540: 177542.     CrossRef
• Covalent Interfacial Anchoring of 1D‐2D Hybrid Nanofillers to Poly(Vinyl Alcohol) Networks Enables High‐Strength, High‐Stiffness Hydrogel Fibers
  Dong Yeop Lee, Ji Hwan Moon, Hocheol Gwac, Gyu Hyeon Song, Hyunsoo Kim, Yongwoo Jang, Changsoon Choi, Seon Jeong Kim
  Advanced Materials.2026;[Epub]     CrossRef

Carbon black with high purity and excellent conductivity is used as a conductive filler in the semiconductive compound for EHV (Extra High Voltage) power cables of 345 kV or higher. When carbon black and CNT (carbon nanotube) are applied together as a conductive filler of a semiconductive compound, stable electrical properties of the semiconductive compound can be maintained even though the amount of conductive filler is significantly reduced. In EHV power cables, since the semi-conductive layer is close to the conductor, stable electrical characteristics are required even under high-temperature conditions caused by heat generated from the conductor. In this study, the theoretical principle that a semiconductive compound applied with carbon black and CNT can maintain excellent electrical properties even under high-temperature conditions was studied. Basically, the conductive fillers dispersed in the matrix form an electrical network. The base polymer and the matrix of the composite, expands by heat under high temperature conditions. Because of this, the electrical network connected by the conductive fillers is weakened. In particular, since the conductive filler has high thermal conductivity, the semiconductive compound causes more thermal expansion. Therefore, the effect of CNT as a conductive filler on the thermal conductivity, thermal expansion coefficient, and volume resistivity of the semiconductive compound was studied. From this result, thermal expansion and composition of the electrical network under high temperature conditions are explained.

A carbon-based hybrid resistor was fabricated using carbon nanotube (CNT) paste as an adhesive layer to establish electrically continuous ohmic contacts between CNT sheets and different CNT sheet or copper based metal alloy plates, and its electrical properties were evaluated. CNT sheets were fabricated using vacuum filtration with a CNT solution dispersed in isopropyl alcohol (IPA) solvent. The electrical characteristics of these carbon-based hybrid resistors were investigated.The CNT paste fulfilled the requirements for forming ohmic contacts between CNT sheets and metal alloy plates, which was attributed to the lowest work function difference and excellent wettability at the interface.

Herein we investigated the effect of the conductive agent on the electrochemical performance of the SiOx anode. SiOx anodes have a relatively low volume expansion (~160%) compared to Pure-silicon, but have a problem in that they have a poor electrical conductivity characteristic. In this study, physical and electrochemical measurements were performed using two 0-dimensional amorphous carbon conductive agents with different crystallinity and surface area. The crystal structure of the conductive agents and the local graphitization degree were analyzed through XRD and Raman, and the surface area of the particles was observed through BET. In addition, the electrical performance according to the graphitization degree of the conductive agents was confirmed through a 4-point probe. As a result of the electrochemical cycle and rate performance, it was confirmed that the performance of SiOx using a conductive agent having a low graphitization degree and a high surface area was improved. The results in this study suggest that the graphitization degree and surface area of the amorphous carbon conductive agent may play an important role in the SiOx electrode.

The carbonaceous materials have attracted much attention for utilization of anode materials for lithium-ion batteries. Among them, hollow carbon spheres have great advantages (high specific capacity and good rate capability) to replace currently used graphite anode materials, due to their unique features such as high surface areas, high electrical conductivities, and outstanding chemical and thermal stability. Herein, we have synthesized various sizes of hollow carbon spheres by a facile hard-template method and investigated the anode properties for lithium-ion batteries. The obtained hollow carbon spheres have uniform diameters of 350 ~ 600 nm by varying the template condition, and they do not have any cracks after the optimization of the process. Increasing the diameter of hollow carbon spheres decreases their specific capacities, since the larger hollow carbon spheres have more useless spaces inside that could have a disadvantage for lithium storage. The hollow carbon spheres have outstanding rate and cyclic performance, which is originated from the high surface area and high electrical properties of the hollow carbon spheres. Therefore, hollow carbon spheres with smaller diameters are expected to have higher specific capacities, and the noble channel structures through various doping approaches can give the great possibility of high lithium storage properties.

We prepared carbon nanotube (CNT) paper by a vacuum filtration method for the use of a chip-typed resistor as a precision passive device with a constant resistance. Hybrid resistor composed of the CNT resistor with a negative temperature coefficient of resistance (T.C.R) and a metal alloy resistor with a positive T.C.R could lead to a constant resistance, because the resistance increase owing to the temperature increase at the metal alloy and decrease at the CNT could counterbalance each other. The constant resistance for the precision passive devices should be maintained even when a heat was generated by a current flow resulting in resistance change. Performance reliabilities of the CNT resistor for the precision passive device applications such as electrical load limit, environmental load limit, and life limit specified in IEC 60115-1 must be ensured. In this study, therefore, the rated power determination and T.C.R tests of the CNT paper were conducted. -900~-700 ppm/℃ of TCR, 0.1~0.2 A of the carrying current capacity, and 0.0625~0.125 W of the rated power limit were obtained from the CNT paper. Consequently, we confirmed that the application of CNT materials for the precision hybrid passive devices with a metal alloy could result in a better performance reliability with a zero tolerance.

Ultrawide bandgap gallium oxide (Ga₂O₃) semiconductors are known to have excellent photocatalytic properties due to their high redox potential. In this study, CO₂ reduction is demonstrated using nanostructured Ga₂O₃ photocatalyst under ultraviolet (254 nm) light source conditions. After the CO₂ reduction, C₂H₄ remained as a by-product in this work. Nanostructured Ga₂O₃ photocatalyst also showed an excellent endurance characteristic. Photogenerated electron-hole pairs boosted the CO₂ reduction to C₂H₄ via nanostructured Ga₂O₃ photocatalyst, which is attributed to the ultrawide and almost direct bandgap characteristics of the gallium oxide semiconductor. The findings in this work could expedite the realization of CO₂ reduction and a simultaneous C₂H₄ production using a low cost and high performance photocatalyst.

We fabricated plate typed shunt resistors composed of carbon nanotube (CNT) and metal alloy for measuring DC current. CNT plates were prepared from dispersed CNT/Urethane solution by squeezing method. Cu/Ni alloys were prepared from composition-designed alloy wires for adjusting the temperature coefficient of resistance (TCR) by pressing them. As well, we fabricated a hybrid resistor by squeezing the CNT/Urethane solution on the metal alloy plate directly. In order to confirm the composition ratio of the Cu/Ni alloy, we used an energy-dispersed X-ray spectroscopy (EDX). Cross-section and surface morphology were analyzed by using a scanning electron microscopy (SEM). Finally, we measured the initial resistance of 2.35 Ω at 25℃ for the CNT paper resistor, 7.56 mΩ for the alloy resistor, and 7.38 mΩ for the hybrid resistor. The TCR was also measured to be -778.72 ppm/℃ at the temperature range between 25℃ to 125℃ for the CNT paper resistor, 824.06 ppm/℃ for the alloy resistor, and 17.61 ppm/℃ for the hybrid resistor. Some of the hybrid resistors showed a near-zero TCR of 1.38, -2.77, 2.66, and 5.49 ppm/℃, which might be the world best-value ever reported. Consequently, we could expect an error-free measurement of the DC current using this resistor.

Using facing target magnetron sputtering (FTMS) with a graphite target source, carbon nitride thin films were deposited on silicon and glass substrates at different substrate temperatures to confirm the tribological, electrical, and structural properties of thin films. The substrate temperatures were room temperature, 150℃, and 300℃. The tribology and electrical properties of the carbon nitride thin films were measured as the substrate temperature increased, and a study on the relation between these results and structural properties was conducted. The results show that the increase in the substrate temperature during the fabrication of the carbon nitride thin films increased the hardness and elastic modulus values, the critical load value was increased, and the residual stress value was reduced. Moreover, the increase in the substrate temperature during thin-film deposition was attributed to the improvement in the electrical properties of carbon nitride thin film.

In this study, we tried finding new materials to improve the stain resistance properties of polymer insulating materials. Using the filtered vacuum arc source (FVAS) with a graphite target source, DLC thin films were deposited on silicon and polymer insulator substrates depending on their thickness to confirm the surface properties, physical properties, and structural properties of the thin films. Subsequently, the possibility of using a DLC thin film as a protective coating material for polymer insulators was confirmed. DLC thin films manufactured in accordance with the thickness of various thin films exhibited a very smooth and uniform surface. As the thin film thickness increased, the surface roughness value decreased and the contact angle value increased. In addition, the elastic modulus and hardness of the DLC thin film slightly increased, and the maximum values of elastic modulus and hardness were 214.5 GPa and 19.8 GPa, respectively. In addition, the DLC thin film showed a very low leakage current value, thereby exhibiting electrical insulation properties.

In this paper, we prepared miniature fuse fabricated with carbon nanotube (CNT) fiber for the use of low rated current under 1 A and high speed operation under 4ms. CNT fuses were fabricated in the form of universal modular fuse (UMF) with different diameter of CNT fibers defined by multiplying the CNT threads. Electrical properties of the CNT fuses were measured such as resistance, rated current, and operation time with current. Resistance of the CNT fuse decreased and rated current increased with the diameter of the CNT fuses, respectively. Consequently, the operation time with current increased with the diameter of the CNT fuses. The CNT fuses fabricated in this work had broad range of low rated current from 0.05 to 1.25 A by multiplying the CNT threads. Operation time was measured about 3.6ms which was applicable to the UMF.

In this study, we produced a light, flexible, wearable gas sensor by depositing MWCNTs (Multi-walled Carbon Nanotubes) into nylon. MWCNTs are widely used as a gas sensor material due to their excellent mechanical, electrical and physical characteristics. We produced a gas sensor to detect NOx gases by depositing nylon yarn in a MWCNT solution. The MWCNT solution was made by mixing 3 mg MWCNT in 5 ml of ethanol. Nylon yarn was placed in the manufactured solution and ultrasonic waves were applied using an ultrasonicator for 3 h, resulting in MCWNT deposition. The MWCNT-deposited nylon yarn was dried at room temperature for 24 h. The MWCNT-thin-film-coated nylon yarn was masked 1 mm apart, and gold was then deposited on the masked nylon yarn to create the gas sensor. The sensor then was installed in a chamber with a controlled atmospheric environment and exposed to NOx gas. The changing signal from the sensor was amplified to analyze its gas detection characteristics.

We prepared yarned carbon nanotube (CNT) fibers from a CNT forest synthesized on a Si wafer by chemical vapor deposition (CVD). The yarned CNT fibers were thermally annealed to reduce their resistance by removing the amorphous carbonaceous impurities present in the fibers. The resistance of the yarned CNT fiber gradually decreased with an increase in the annealing temperature from 200℃ to 400℃ but increased again above 450℃. We carried out thermogravimetric analysis (TGA) to confirm the burning properties of the amorphous carbonaceous impurities and the crystalline CNTs present in the fibers. The pattern of the mass change of the sample CNT fibers was very similar to that of the resistance change. We conclude that CNT fibers should be thermally annealed at temperatures below 400℃ for reducing and stabilizing their resistance.

Raman spectra of a-C:H thin films deposited with an unbalanced magnetron sputtering system showed that the G peak shifted to a higher wavenumber as the target power density increased and ID/IG ratio increased from 0.902 to 1.012. Moreover, the transmittance of a-C:H films fabricated at 60 nm tended to decrease with increasing target power density; at 550 nm in the visible light region, the transmittance decreased from 69% to 58%. The rms surface roughness values of the a-C:H thin films decreased with increasing target power density, and varied from 1.11 nm to 0.71 nm. In order to achieve efficient light trapping, the light scattering at the rough interface must be enhanced. Consequently, the surface roughness of the thin film will decrease with the target power density. Further, the refractive index and reflectivity of the a-C:H thin films increased with increasing target power density; however, the Brewster angle decreased with the target power density. Hence, dye-sensitized solar cells using an a-C:H antireflective coating increased the CE, VOC, and JSC by approximately 8.6%, 5.5%, and 4.5%, respectively.

In this study, we fabricated plate-type shunt resistors with thermal stability by parallelly connecting metal alloy plates with positive temperature coefficient of resistance (TCR) and carbon nanotube (CNT) plates with negative TCR. The metal alloy plates, which were prepared by alloying Cu and Mn with a composition of 91 wt% of Cu and 9 wt% of Mn, showed around 800 ppm/℃ of TCR, and the CNT plates prepared from the CNT solution by using the vacuum filtration method showed around -800 ppm/℃ of TCR. The shunt resistor that was fabricated by stacking metal alloy plates and CNT plates in this work showed about 46.93 ppm/℃ of TCR. Therefore, we conclude that a shunt resistor with low TCR can be realized by simply adjusting the TCR of the metal alloy only, because the TCR of the CNT plate has an identical value.

This work investigated the effects of different conductive agents on the electrochemical properties of anodes. SiOx possesses high theoretical capacity and shows excellent cycle performance; however, the low initial coulombic efficiency and poor electrical conductivity limit its applications in real batteries. In this study, electrodes were fabricated using two different conductive agents, and the resulting physical and electrochemical properties were analyzed. SEM observations confirmed the formation of a CNT conductive network throughout the electrodes, while the electrical conductivity contributed to the electrode was confirmed by impedance measurements. Thus, the electrode fabricated with the CNT conductive agent showed greater capacity and superior cycle performance than did the electrode fabricated using the DB conductive agent.

We investigated the tribological properties of amorphous carbon (a-C) films deposited with CrC interlayers of various thicknesses as the adhesive layer. A-C and CrC thin films were deposited using the unbalanced magnetron (UBM) sputtering method with graphite and chromium as the targets. CrC films as the interlayer were fabricated under a-C films, and various structural, surface, and tribological properties of a-C films deposited with various CrC interlayer thicknesses were investigated. With various CrC interlayer thicknesses under a-C films, the tribological properties of CrC/a-C films were improved; the increased film thickness exhibited a maximum high hardness of over 27.5 GPa, high elastic modulus of over 242 GPa, critical load of 31 N, residual stress of 1.85 GPa, and a smooth surface below 0.09 nm at the condition of 30-nm CrC thickness.

A nanofiber was fabricated with carbon nanotubes for transparent electrodes. It was prepared with a composite solution of bio-molecules polycaprolactone (PCL) and multiwalled carbon nanotubes (MWCNTs) by electrospinning on a glass substrate, following which its electrical characteristics were investigated. The content of MWCNTs was varied during electrospinning, while that of PCL was fixed. Further, a nanometer-thick thin film of silver was deposited on the nanofiber layer using a thermal evaporator to improve the electrical characteristics; the sheet resistance significantly reduced after this deposition. The results showed that this carbon nanotube nanofiber has potential applications in biotechnology and as a flexible transparent display material.

In this study, we fabricated an NOX gas sensor using a composite film of multi-walled carbon nanotubes (MWCNT)/zinc oxide (ZnO). Carbon nanotubes (CNTs) show good electronic conductivity and chemical-stability, and zinc oxide (ZnO) is a wide band gap semiconductor with a large exciton binding energy. Gas sensors require characteristics such as high speed, sensitivity, and selectivity. The fabricated gas sensor was used to detect NOX gas at different NOX concentrations. The sensitivity of the gas sensor increased with increasing gas concentrations. Additionally, while changing the temperature inside the chamber containing the MWCNT/ZnO gas sensor, we obtained the sensitivity and normalized responses for detecting NOX gas in comparison to ZnO and MWCNT film gas sensors. From the experimental results, we confirmed that the gas sensor sensing mechanism was enhanced in the composite-film gas-sensor and that the electronic interaction between MWCNT and ZnO contributed to the improved sensor performance.

Inductively coupled plasma (ICP) treatment with argon and a mixture of argon and oxygen gases has been used to modify the surface of polycarbonate (PC) substrates. The results showed that the surface contact angle was inversely proportional to the plasma discharge power and that the mixed-gas plasma (gas flow 10:10 sccm, discharge power 60 W) decreased the surface contact angle as low as 18.3°, indicating a large increase in the surface hydrophilicity. In addition, SnO₂ thin films deposited on the PC substrate effectively enhanced the ICP plasma treatment, and could also enhance the usefulness of PC in the inner parts of automobiles.

Various Ni-doped carbon (C：Ni) thin films were fabricated using different Ni target power densities by unbalanced magnetron sputtering (UBM). The effects of target power density on the structural, physical, surface, and electrical properties of C：Ni films were investigated. The UBM C：Ni thin films exhibited uniformly smooth surfaces. The rms surface roughness and friction coefficient values of the C：Ni films decreased with the increase in target power density. The physical properties of the films such as hardness and elastic moduli increased while their electrical properties such as resistivity decreased with the increase in the target power density. These results show that an increase of the power density leads to an increase in the proportion of Ni and nanocrystallization of the amorphous carbon film; this contributes to the changes observed in the physical and electrical characteristics.

CNT (carbon nanotube) resistors with low resistance and negative TCR (temperature coefficient of resistance) were fabricated with yarned CNT (carbon nanotube) fibers. The CNT fibers were prepared by yarning CNTs grown on the silicone substrate by CVD (chemical vapor deposition) method. The CNT resistors were fabricated by winding CNT fibers on the surface of ceramic rod. Both metal terminals were connected with the CNT fiber wound on the ceramic rod. We measured electrical resistance and thermal stability with the number of CNT fibers wound. The CNT resistor system shows linearly decreased resistance with the number of CNTs wound on the ceramic rod and saturated at 20 strands. The CNT resistor system has negative TCR between -1,000 ~ -2,000 ppm/℃ and stable frequency properties under 100 kHz.

Mo doped carbon (C:Mo) thin films were fabricated with various Mo target power densities by unbalanced magnetron sputtering (UBM). The effects of target power density on the surface, structural, and electrical properties of C:Mo films were investigated. UBM sputtered C:Mo thin films exhibited smooth and uniform surfaces. However, the rms surface roughness of C:Mo films were increased with the increase of target power density. Also, the resistivity value of C:Mo film as electrical properties was decreased with the increase of target power density. From the performance of organic thin filml transistor using conductive C:Mo gate electrode, the carrier mobility, threshold voltage, and on/off ratio of drain current (Ion/Ioff) showed 0.16 cm²/V·s, -6.0 V, and 7.7×10⁴, respectively.

Hole explosion behaviors were observed during drilling fine holes with laser beam on the LTCC green bar of 320 ㎛ thick after lamination of green sheets prepared by tape casting of thick film process. The incidence of these hole explosions was inversely proportional to hole sizes. The incidence of hole explosion was 20 % number of hole with the size of 60 ㎛ exploded for the UV radiation, while the explosion did not appear for hole sizes over 100 ㎛. To prevent hole explosion behavior during laser-drilling of fine holes, carbon black powder was added as an additive in the LTCC composition, which has superior thermal durability. As a consequence, hole explosion rate was suppressed to 0.8 % for the hole size of 50 ㎛ green sheet with the carbon black amount of 10 weight % and the laser power of 3 watt. Added carbon is thought to reduce the heat-affected region during laser drilling.

We investigated the characterizations of carbon films fabricated by dual magnetron sputtering under various film thickness for the electrodes in TCO-less DSSC (dye-sensitized solar cells). Carbon films prepared at various conditions were exhibited smooth and uniform surfaces without defects. Also, the rms surface roughness of carbon films was decreased from 2.25 nm to 1.0 nm with the increase of film thickness. The sheet resistance as the electrical properties are improved from 11.2×10^-3 to 2.28×10^-3 with the increase of film thickness. In the results, the performance of TCO-less DSSC critically depended on the film thickness of working electrodes, indicating the conductivity of carbon films.

In this study, we fabricated NOX gas sensor by using multi-walled carbon nanotubes(MWCNT)/zinc oxide(ZnO) composite film. Carbon nanotubes (CNTs) have good electronic, chemical-stability, and sensitivity characteristics. And zinc oxide (ZnO) is a wide band gap and large exciton binding energy semiconductor. In particular, gas sensors require characteristics such as high speed, sensitivity, and selectivity. The fabricated gas sensor was used to detect NOX gas for different values of the NOX gas concentrations. The gas sensor that absorbed NOX gas molecules showed a increasing in resistance. The sensitivity of the gas sensor was increased by increasing the gas concentrations. Additionally, while changing the temperature inside the chamber for the MWCNT/ZnO composite film gas sensor, we obtained the sensitivity. And the comparison analysis to ZnO film gas sensor for detecting NOX gas. From the experiment result, we confirmed improvement of NOX gas detection characteristics using the MWCNT/ZnO composite film.