The continuous rise of atmospheric carbon dioxide (CO₂) emissions highlights the urgent need for sustainable air purification technologies. Current Direct Air Capture (DAC) filters often rely on toxic amines, which limit long-term stability and safe application. Here, we report a non-toxic PAN-based nanofiber air filter fabricated by electrospinning and urea-assisted carbonization. Structural analyses confirmed the introduction of nitrogen functionalities that enhanced CO₂ affinity, while SEM and FT-IR revealed graphitic carbon formation. In air-chamber tests, the optimized carbonized nanofiber reduced CO₂ concentration from 25,000 ppm to 2,000 ppm, a level generally regarded as acceptable for indoor environments, while simultaneously removing over 95% of PM10, PM2.5, and PM0.1 particulates. This dual functionality, combined with facile fabrication and material safety, demonstrates strong potential for PAN-derived carbon nanofiber membranes in DAC systems and eco-friendly air purification devices. These findings suggest a viable pathway toward scalable, sustainable air-filter technologies for carbon-neutral applications.
Nozzle-printing dispensers, which utilize air pulsation as a dispensing principle, operate by transmitting air pressure to the liquid to push a constant amount of liquid. Nozzle printers have the advantage of precisely controlling energy based on liquid properties, such as viscosity and surface tension, enabling the precise application of liquid at specific locations and quantities. This study introduces a printing process sequence using a nozzle printer equipped with a high-resolution vision alignment system. It compares printing patterns according to key process variables (jet pressure, tip height, and travel speed) that affect coating quality. Experimental results showed that a coating standard deviation of 2.14 μm was achieved at a moving speed of 20 mm/s and a nozzle height of 0.2 mm, resulting in the most stable and uniform coating quality. Through these experiments, optimal conditions were identified based on factors such as coating width, uniformity, and presence of discontinuity, and the effects of these conditions on the precision manufacturing process are discussed.
Citations
Citations to this article as recorded by
Flexible piezoelectric cross-bar array sensors for upper-limb kinesthetic sensing via muscle dynamics Junki Lee, Jihun Choi, Hyunseung Kim, Min Gon Son, Dong Yeol Hyeon, Jung Hwan Park, Andris Šutka, Chang Kyu Jeong Journal of the Korean Ceramic Society.2026;[Epub] CrossRef
It is highly important issue to use an energy efficiently for sustainable prosperity of mankind. From this point of view, using LED lighting can be a good alternative because it has a lot of advantages such as high efficiency, long life time and eco-friendly manufacturing process. That is the reason why using LED lighting has been encouraged worldwide. However, in situations that LED lighting is replacing traditional lighting quickly, the problem of the flicker of LED lighting has emerged as an important issue. Therefore, in foreign countries like US or Japan in order to ensure the reliability of LED lighting, study for flickering effects of the human body and test methods are have been actively conducted. But related research in domestic situation is an insufficient condition. In this study, a flicker characteristic was measured conventional lamps such as incandescent lamps or fluorescent lamp and 81 items of LED lightings which are distributed in domestic markets.
Goethite, α-FeOOH have various applications such as absorbent, pigment and source for magnetic materials. Goethite particles were synthesized in a two step process, where Fe(OH)2 were synthesized in nitrogen atmosphere using FeSO4 as a raw material in the first process, and after that acicular goethite particles were obtained in an air oxidation process of Fe(OH)2 in highly alkaline aqueous solution. Their phase and microstructure were investigated with XRD and FE-SEM. It was found that the morphology of goethite and the ratio of length-to-width (aspect ratio) of acicular goethite are dependent on the some factors such as R value (OH-/Fe2+), air flow rate and pH conditions. In particular, R value has the strongest influence on the synthesized goethite morphology. It is considered that the optimal value R is 4.5 because X-ray diffraction peaks of goethite have the highest intensity at that value. Morphology of goethite particles was controlled by air flow rates, showing that their size and aspect ratio are getting smaller and decrease, respectively as air flow rate increases. The largest goethite particle obtained is about 1,500 nm in length and 150 nm in diameter.
Hybrid supercapacitors with high power density and long cycle life are widely used for emergency power source of LED emergency luminaires. In this paper, we designed and fabricated a hybrid capacitor cell and a module for the LED emergency luminaires. Using hybrid supercapacitor cells (1,000 F, 2.8 V), we designed a module in a 10-year warranty considering aging and ESR. Considering the ESR and efficiency has been designed to module with 1,000 F 5.6 V design results in 2 series and 2 parallel combination. Module was used to confirm that the operation 77.5 minutes at room temperature, discharge LED emergency luminaires with 2 W. As a LED emergency luminaires of emergency power supply that we can support more than 10 years of life was confirmed the applicability of hybrid supercapacitor.
The needle electrode is inserted into the cross-linked polyethylene(XLPE) which is the ultrahigh voltage cable for electric power. By changing the tilt of the needle electrode, we investigated how the void and the thickness of the insulating layer influence the partial discharge(PD) characteristics and the insulating breakdown. In order to investigate the PD characteristics, The XLPE cable was used to the specimens and the tungsten electrode was used with the needle electrode. And the inner semi-conductive layer material of XLPE cable was used with the negative electrode by bonding with the use of conduction tape. The size of the specimens was manufactured to be 16×40×30 [㎣]. We confirmed the effect on changing the PD characteristics according to the changing voltage and the tilt of the electrode after applying the voltage on the electrode from 1[kV] to 40[kV] at room temperature. In the PD characteristics, it was confirmed that the PD current of air void specimens with tilt was unstable more than that of no void specimens with tilt. It was also confirmed that the breakdown voltage was decreased because the effect of air void is more active than the change of the needle electrode tilt in the specimen with air void inside the insulation.
Tubular-shaped ZnO crystals were synthesized by thermal evaporation technique under air atmosphere. Mixture of Zn and Mg powder was used as the source material. The thermal evaporation and oxidation of Zn/Mg mixture were carried out for 1 hr at 1,000℃ and 1,200℃ under in air under atmospheric pressure. When only Zn powder was used as a source material, tetrapod-shaped ZnO crystals were synthesized. This provides that Mg played a key role in the formation of the tubular-shaped crystals. SEM images showed that the tubular-shaped ZnO crystals grew along [0001] direction. XRD spectrum revealed that the ZnO tubes had hexagonal wurtzite structure. Two emission peaks at 380 nm and 510 nm were observed in the room temperature cathodoluminescence spectrum.
In order to develop a LED luminaire for naval-submarines which can replace a conventional one with two-compact fluorescent lamp (CFL) of 18 W, we analyzed the electrical and optical performance of the conventional luminaire. A LED luminaire was fabricated as compact as possible based on the analyzed data. The weight of the prototype LED luminaire is 1.8 kg, reducing up to 58% of the conventional one. The use of LED package for the submarine luminaire could reduce the power consumption from 38 W to 14.5 W with the same optical performance. The reason is that the optical efficacy of the LED luminaire improved by 2.47 times as 61.9 lm/W, compared to 25.1 lm/W for the conventional one.
ZnO crystals with octahedral shape were synthesized by thermal evaporation technique. ZnF2 powder was used as the source material. The thermal evaporation and oxidation of ZnF2 powder was carried out for 1 hr at 1,000℃ in air under atmospheric pressure. SEM images showed that the ZnO crystals produced by oxidizing ZnF2 vapor possessed a characteristic octahedral shape. XRD spectrum revealed that the ZnO octahedron had hexagonal wurtzite structure. In the room temperature photoluminescence spectrum, a strong green emission peak at around 510 nm was observed.
This paper conducted a study on how the heat radiation of light emitting diode (LEI)) luminaires affects the indoor temperature increase. The effect was compared with that of a 20 W compact fluorescent lamp (CFL) and a 50 W MuG halogen lamp which are most widely used inside of cruises, a LED downlight and a 4W MRI6 LED replacing each of them. We installed a luminarie inside a thermally shielded chamber, measuring the temperature changes under the same volume every 5 minutes and compared the result with theoretically calculated heat radiation, The temperature changes in the chamber was measured four times, on seven hours` period in order to keep sufficient time once the temperature reaches the thermal equilibrium state. The results showed that the temperature of the 20 W E26 CFL and the 10 W LED downlight increased by 21,1`C and 10.4t respectively, while that of the 50 W halogen MRI6 and the 4 W LED MR16 increased by 33.9t and 4.8t respectively. The experimental heat radiation were calculated from the results and the experimental heat radiation of the CFL and the LED downlight were 171.5 cal and 86.5 cal, and those of the halogen MR16 and the LED MR16 were 275.3 cal and 36.5 cal, Therefore, the heat radiation was reduced by 49.5% and 86.7%, respectively, by replacing conventional light source with LED. In conclusion, we can expect a reduction of power consumption in air condition system and the effect on indoor temperature increase by application of LED luminaires.
ZnO crystals with a baseball bat shape were synthesized without any catalysts through a simple thermal oxidation of ZnS powder in alumina crucible under air atmosphere. SEM images demonstrated that the bat structure was composed of two pieces of ZnO crystals, i.e hexagonal-shaped rod and inverted cone-shaped rod. X-ray diffraction (XRD) pattern revealed that the ZnO crystals had wurtzite hexagonal structure. Energy dispersive X-ray (EDX) spectrum showed that the ZnO was of high purity. A strong green emission peak at 510 nm was observed in cathodoluminescece spectrum.
Nowadays, with improvement of economical income and life qualities, life pattern changes have been brought such as increasing of avocational activities. Consequently, following those life trends, utilization of car is getting increased. Thus, the perceptions of car have been changed from the only means of transport in the past to a 2nd residental space. that is why the car`s endo environmental factors are getting so important. Air conditioner regulating air ventilization in vehicle`s indoor automatically sets the right temperature based on the differences of indoor and outdoor`s temperature with development of advanced functions to provide better environmental qualities in vehicle. However, even those advanced techniques for functional development are got so diverse though, the essential technique for preventing the growth of bateria and mold inside of the air conditioner are not even severals. Especially, evaporator one of the vehicle air conditioning equipments generates cooled air by vaporizing refrigerant in liquid state with the water as the adduct for this reactions. It has structural difficulties for water vaporation then cause the growth of germs. That`s why this reseach was focused on the way of eliminating germs in the vehicle air conditioner efficiently. Direct air sterilizer by using UVC(Ultraviolet C) is manufactured and that performances are evaluated.
ZnO crystals with belt and comb shapes were synthesized without any catalysts through a simple thermal oxidation of ZnS powder in alumina crucible under air atmosphere. X-ray diffraction (XRD) pattern revealed that the ZnO crystals had wurtzite structure of hexagonal phase. Energy dispersive x-ray (EDX) spectra showed that the ZnO was of high purity. In the cathodoluminescece spectra obtained for the ZnO crystals with belt and comb shapes, a strong ultraviolet emission centered at 380nm was observed, which indicates the ZnO crystal has high crystalline quality.
ZnO nanostructures with tetrapod, needle and multipod shapes were synthesized without catalysts through a simple thermal oxidation of metallic Zn powder in alumina crucible under air atmosphere. X-ray diffraction data revealed that the ZnO nanostructures had wurtzite structure of hexagonal phase. Energy dispersive X-ray (EDX) spectra showed that the ZnO was of high purity. After the oxidation of Zn powder, white colored product was mainly observed and yellow colored product was observed only a very little on the surface of the oxidized source materials. The white product consisted of tetrapods, while yellow product was composed of needles and multipods. Cathodoluminescece spectra showed that the crystalline quality of tetrapods was better that those of needles and multipods.
In this study, magnesium (Mg), zinc (Zn) and aluminium (Al) as anode electrode and the solution of NaCl dissolved with 2~20 wt% as electrolytes were used for the metal-air cell. The open circuit voltage, short circuit current and I-V characteristics upon different kinds of anode electrode and electrolyte concentration were investigated. The open circuit voltage, initially about 1.45 V, rises to 1.6 V during the first 10 minutes indicating the necessity of an induction time to activate the catalyst on the air cathode. The short circuit current increases with an increased concentration of NaCl, causes an increase in the conductivity of the electrolyte solution, but the open circuit voltage did not under undergo influence of electrolyte. From NaCl 20 wt% electrolyte, the maximum output power of the magnesium electrode materials was measured with 177mW. It is found that the power characteristics of metal-air cell could be improved by using magnesium electrode materials in the NaCl electrolyte.
Citations
Citations to this article as recorded by
Prediction of electrolyte refresh time for Mg-Air battery Jongwoo Park, Kwangyeop Jang, Sangwon Seo, Jaehyo Park, Wansung Kwon, Dongjin Kim, L. Zhang, S. Defilla, W. Chu E3S Web of Conferences.2021; 233: 01013. CrossRef
A study on the electrolyte circulation effect of Mg-air battery Jongwoo Park, Kwangyeop Jang, Sangwon Seo, Jaehyo Park, Wansung Kwon, Dongjin Kim, L. Zhang, S. Defilla, W. Chu E3S Web of Conferences.2021; 233: 01043. CrossRef
In this paper, we studied the dielectric breakdown voltage characteristics by the AC withstand voltage test on using green insulation dry air instead of SF6 insulation gas used in the GIB (gas insulated bus) of 362 kV GIS (gas insulated switchgear). The AC withstand voltage test applied to the standard KEPCO`s 362 kV GIB with dry air insulation, and the equivalence of dielectric breakdown voltage for dry air and SF6 gas were examined, and the empirical formulas of dielectric breakdown voltage for dry air were calculated, and the criterion of AC withstand voltage test for dry air insulation was derived. Using the criterion, dry air can be used instead of SF6 gas for 362 kV GIB in the factory acceptance test was confirmed.
Characteristics of Organic Thin Film Transistors with Organic and Organic-inorganic Hybrid Polymer Gate Dielectric In Seob Bae, Ha Young Lim, Su Heon Cho, Song Hee Moon, Won Seok Choi Journal of Korean Institute of Electrical and Electronic Materials Engineers.2009; 22(12): 1009. CrossRef
Preparation and Electrochemical Properties of Pr1-x(Sr, Ca)xCoO3Cathode Materials for Zinc Air Batteries Sang-Hun Heo, Seung-Wook Eom, Hyun-Soo Kim Journal of the Korean Electrochemical Society.2009; 12(4): 342. CrossRef
Provisioning the standard method for ensuring the reliability of indoor air quality measurements in public transportation Ho-Hyun Kim, Ho-Hyeong Yang, Jeong-Hun Lee, Sang-Hyeon Kang, Tae-Hyun Kim, Sung-Lyul Kim Journal of Odor and Indoor Environment.2020; 19(1): 47. CrossRef
Comparison of particle removal efficiency between the physical cleaning methods in the fabrication of liquid crystal displays Chang-Beom Park, Seung-Jun Yi, In-Soung Chang Journal of the Korea Academia-Industrial cooperation Society.2010; 11(3): 795. CrossRef
First
Prev
