β-Ga₂O₃ is an ultra-wide bandgap semiconductor promising for high-power electronic applications; however, heteroepitaxial growth on sapphire is challenging lattice and symmetry mismatch. In this study, β-Ga₂O₃ thin films were grown on C-plane sapphire substrates with various off-axis angles (0–12°) using mist-CVD, and the influence of substrate miscut on structural and optical properties was investigated. All films grown at 900°C exhibited (-201) oriented β phase. The crystal quality was strongly dependent on the off-axis angle, with intermediate off-axis angles (Δ_a = 6–8°) showing the narrowest rocking curve width. Off-axis substrates promoted step-aligned growth behavior compared to on-axis growth. Optical measurements revealed enhanced transmittance and wider bandgap values (4.92–4.95 eV) for off-axis samples compared to the on-axis film (4.69 eV). The findings provide practical guidelines for optimizing heteroepitaxial β-Ga₂O₃ growth on low-cost sapphire substrates for high-performance device applications.

e investigated the effects of post-annealing in vacuum, nitrogen, and hydrogen atmospheres on the structural, electrical, and optical properties of 600 nm thick Al-doped ZnO (ZnO:Al) thin films deposited by RF magnetron sputtering at room temperature. Post-annealing in hydrogen atmosphere at 400℃ for 1 hour showed the most significant improvement in electrical properties. Resistivity decreased from 9.11×10⁻³ to 1.4×10⁻³ Ω·cm, electron mobility increased from 4.11 to 18.23 cm²/V·s, and electron carrier concentration increased from 1.63×10²⁰ to 4.85×10²⁰ cm⁻³. In contrast, post-annealing in vacuum and nitrogen atmospheres resulted in degraded electrical properties due to oxygen and nitrogen chemisorption at grain boundaries. The enhancement in hydrogen-annealed films was attributed to the formation of additional oxygen vacancies and desorption of adsorbed oxygen species from grain boundaries. All films maintained excellent optical transparency of 80-90% in the visible range. The optical bandgap exhibited a blue-shift from 3.365 eV to 3.624 eV due to the Burstein-Moss effect induced by the increased electron carrier concentration. These results confirmed that hydrogen atmosphere post-annealing is the most effective method for enhancing the electrical conductivity of ZnO:Al thin films while maintaining high optical transparency.

In this study, Y₂O₃ thin films were deposited on Si(100) wafers using an RF sputtering system with a Y₂O₃ target. The Y₂O₃ thin film was confirmed to have a thickness of 227 nm/min and a uniformity of 1.34% at a substrate temperature of 400℃. All samples were annealed at 600, 800, and 1,000℃ for 1 hour in an O₂ gas atmosphere using the furnace. The analysis of the XRD patterns revealed that the peak intensity increased with annealing up to 800℃, but decreased when the annealing temperature was raised to 1,000℃. The XPS analysis confirmed the onset of crystallization at 800℃, in agreement with the trends observed in the XRD results. According to the AFM results, the surface became slightly smoother after heat treatment, as indicated by a reduced RMS roughness of approximately 1.792 nm.

κ-phase Ga₂O₃ is a wide-bandgap semiconductor that has attracted attention for power and optoelectronic device applications. However, its crystal quality and optical properties are highly dependent on the growth temperature, which motivates the need for a systematic study. In this work, κ-Ga₂O₃ thin films were grown on AlN/sapphire templates using mist-CVD at different temperatures. At lower temperatures (400℃), films exhibited incomplete crystallization and partial opacity, whereas higher growth temperatures (500-700℃) produced transparent films with improved properties. The bandgap was found to increase with temperature, consistent with reported values for 600-700℃, and XRD/XRC analysis confirmed that crystal quality improved with higher growth temperature. AFM analysis further revealed reductions in surface roughness and grain size variation at elevated temperatures. These findings indicate that an optimal growth window of 600-700℃ enables high-quality κ-Ga₂O₃ films, with potential implications for integrating this material on other hexagonal substrates such as SiC and GaN.

Molybdenum disulfide (MoS₂) is a promising 2D semiconductor material for low-power electronics due to its excellent electrical properties and compatibility with conventional processes. In this study, MoS₂ thin films deposited by RF sputtering were etched using Cl₂/Ar plasma in an ICP system. The effects of Cl₂ gas ratio, RF power, and process pressure on etch rate and MoS₂/SiO₂ selectivity were investigated. Optimal results were obtained at 25% Cl₂, achieving ~38 nm/min etch rate and selectivity of 3.0. Increased source power improved both etch rate and selectivity, while higher bias power enhanced etching but reduced selectivity due to stronger ion bombardment. XPS analysis confirmed Mo－Cl and S－Cl bond formation after etching, indicating chemical reactions and some by-product residue. These results provide insights into optimized plasma etching of sputtered MoS₂ films for advanced 2D device fabrication

In this study, we investigated the electrical stability and performance enhancement of In₂O₃ thin-film transistors (TFTs) through hydrogen peroxide (H₂O₂) and ultraviolet (UV) treatment under controlled temperature conditions. The In₂O₃ TFTs were fabricated using a sol-gel process, followed by H₂O₂ treatment at 40, 50, and 60℃ in combination with UV irradiation. The impact of these processing conditions on the device characteristics, including mobility (μ), threshold voltage (Vth), subthreshold swing (S/S), and on/off current ratio, was systematically analyzed. The results indicate that the 50℃ TFTs exhibited the most stable electrical performance, with minimal Vth shift under negative bias stress (NBS) conditions and optimized switching behavior. Furthermore, static inverter measurements confirmed the reliable voltage transfer characteristics (VTCs) and gain performance of the optimized In₂O₃ TFTs. These findings suggest that the proposed H₂O₂ and UV treatment technique can effectively improve the reliability and long-term stability of In₂O₃-based electronic devices, making them promising candidates for future electronic applications.

Recently, oxide semiconductors have assumed a pivotal role in electronic displays and transparent electronic devices such as amorphous indium gallium zinc oxide (a-IGZO), characterized by high electron mobility and excellent stability. a- IGZO is very suitable for next-generation applications such as flexible displays because it is possible to manufacture highperformance transistors even at low temperatures. However, since the electrical properties tend to deteriorate in hightemperature environments, research aimed at improving thermal stability is needed. In this study, a low-temperature plasma annealing process was introduced to improve the high-temperature stability of the a-IGZO thin film. This process enhances electron mobility by reducing defects in the a-IGZO film and provides stable device performance even under high-temperature conditions. As a result of the experiments of 5 min, 10 min, 15 min, and 20 min, the a-IGZO TFT, which was subjected to plasma annealing at 160℃ for 5 min, showed the best electrical performance, especially in charge mobility and current-voltage characteristics. The technical potential for improving the performance of a-IGZO-based display device was emphasized, and the foundation for applying this power generation to flexible displays and next-generation electronic devices was laid. Future research will focus on determining the optimal annealing conditions by exploring various temperature ranges and plasma parameters to integrate these results into the actual device manufacturing process. These efforts are expected advance significantly to advancing next-generation high-performance display technology.

Piezoelectric thin films have become increasingly significant in applications such as MEMS devices, wearable electronics, and lab-on-a-chip systems due to the miniaturization and integration of electronic devices. For piezoelectric thin films, even when an electric signal is applied in the thickness direction, greater deformation can often be observed in the in-plane direction, which is perpendicular to the electric field. Therefore, piezoelectric thin film devices are frequently designed using the transverse mode. As a result, it is crucial to evaluate piezoelectric thin films by measuring their transverse piezoelectric coefficient. This tutorial paper introduces a method for evaluating the effective transverse piezoelectric coefficient (e_31,f) of piezoelectric thin films using laser Doppler vibrometry (LDV). Additionally, the paper outlines a step-by-step procedure for measuring e31,f while using Bi_1/2Na_1/2TiO₃-based piezoelectric thin films as an example. This tutorial is expected to provide a practical and valuable method for measuring and analyzing the transverse piezoelectric properties, thereby supporting the development of new piezoelectric thin film materials.

In this study, the effect of thickness on the Sn-doped β-Ga₂O₃ thin films was investigated. β-Ga₂O₃ is a next-generation material for power semiconductors and optoelectronics owing to its remarkable properties, such as an ultra-wide bandgap, excellent thermal and chemical stability, and large breakdown voltage. However, its inherently low conductivity can be limiting in applications that require high conductivity; therefore, improving the conductivity of β-Ga₂O₃ is important. In this study, Sn-doped β-Ga₂O₃ thin films with various thicknesses were deposited on β-Ga₂O₃ substrates. All the fabricated samples exhibited β-phase with a uniform and dense surface and transmittance of above 80% in the visible region. In particular, the 100 nm samples showed the highest carrier concentration and mobility and the lowest resistivity. Thus, these findings are expected to play an important role in improving the performance of devices by controlling the thickness of thin films.

Al-Mo thin films were fabricated using combinatorial sputtering system to realize highly sensitive surface acoustic wave (SAW) devices. The Al-Mo sample library was grown with various chemical compositions and electrical resistivities, which provided important information for selecting the most suitable materials for SAW devices. As the SAWs generated from piezoelectric materials are significantly affected by the resistivity and density of the interdigital transducer (IDT) electrodes, three types of Al-Mo thin films with different Al contents were fabricated. The thickness of the Al-Mo thin film used in the SAW-IDT electrode was fixed at 150 nm. As the Al content of the Al-Mo thin film decreased from 81.2 to 30.3 at%, the resistivity decreased slightly from 5.43±0.15 to 4.87±0.1×10^-5 Ω-cm, whereas the calculated density increased significantly from 4.1 to 7.9 g/㎤. The SAW device composed of Al-Mo IDT electrodes resonated at 143 MHz without frequency shifts; however, the selectivity of the resonant frequency and insertion loss deteriorated as the Al content decreased. This suggest that the resonant characteristics of the SAW devices fabricated with Al-Mo thin films were more strongly influenced by the material density rather than the electrical properties of the IDT electrodes.

In this study, the electrical properties of zinc oxide (ZnO) thin-film transistors (TFTs) based on oxide semiconductors were analyzed. As interest in next-generation transparent and flexible displays grows, ZnO, which offers high field-effect mobility and transparency, has emerged as a promising material to overcome the limitations of amorphous silicon (a-Si)-based TFTs. ZnO has a wide bandgap and optical transparency and can be deposited on various substrates at low temperatures, making it a suitable channel material for future display devices. In this study, ZnO TFTs were fabricated with an inverted staggered structure using a p⁺⁺ Si wafer coated with SiO₂ as the substrate. The ZnO channel layer was deposited by RF magnetron sputtering, and the ITO source/drain electrodes were formed using an e-beam evaporator. The electrical characteristics was evaluated using Keithley 4200A-SCS parameter analyzer. Mobility, On/Off ratio, and subthreshold swing (SS) were calculated from the measurements.

The display industry has recently been at the forefront of innovative advancements in modern electronic devices. Technological progress such as flexible display holds significant potential across various application fields, particularly in wearable devices and rollable displays. A low-temperature process is essential for fabricating such displays. One of the key technologies in displays is the thin film transistor (TFT), with amorphous indium gallium zinc oxide (a-IGZO) receiving particular attention. a-IGZO is widely applied in high-performance displays due to its high charge mobility and stability. While a thermal treatment above 350℃ is typically required to maximize the electrical performance of a-IGZO TFTs, such high temperatures pose challenges for utilizing polymer substrates like plastics. Here, we thesis investigates the simultaneous lowtemperature plasma annealing process to develop next-generation high-performance flexible display devices. To define the optimal temperature, devices were fabricated and analyzed at varying temperatures of 40℃, 80℃, 120℃, and 160℃. Experimental results indicated that devices fabricated at 160℃ and 80℃ exhibited superior performance, with those at 160℃ demonstrating better performance in terms of current ratio, threshold voltage, and subthreshold swing. These findings confirm that the simultaneous low-temperature plasma annealing process is effective for next-generation high-performance displays.

With the recent development of emerging technologies, information acquisition and delivery between users has been actively conducted, and inorganic thin film transfer technology that effectively transfers various materials and devices is being studied to develop flexible electronic devices accordingly. This is aimed at innovative structural changes and functional improvement of electronic devices in the era of the Internet of Things (IoT). In particular, advanced technologies such as micro- LEDs are used to realize high-resolution flexible displays, and the possibility of heterogeneous integrated technologies can be presented by precisely transferring materials to substrates through various transfer process. This paper introduced physical, chemical, and self-assembly transfer methods based on inorganic thin film materials to implement heterogeneous integrated flexible semiconductor systems and introduces the results of application studies of semiconductor devices obtained through different transfer technologies. These studies are expected to bring about innovative changes in the field of smart devices, medical technology, and user interfaces in the future.

This work focuses on improving the light-harvesting efficiency of thin-film silicon solar cells through innovative multi-architecture surface modifications. To create a regular optical structure, a lithographic process was performed to form it on a glass substrate through various etching processes, from Etch-1 to Etch-3. AZO was deposited on top of the structures and re-etched to create a multi-architectural surface. These surface-modified structures improved the light absorption and overall performance of the solar cell through changes in optical and physical properties, which we will analyze. In addition, we investigated the effect of post-cleaning on the etched glass structures through EDX analysis to understand the mechanism of the etching action. The results of this study are expected to provide important guidelines for the design and fabrication of solar cells and other photovoltaic devices.

The low-temperature deposition of BaNi_(2-x)Co_xFe₁₆O₂₇ thin films with a Ba hexaferrite structure for electromagnetic shielding was studied. The BaNi_(2-x)Co_xFe₁₆O₂₇ thin films produced through the spin spray process were suitable for thin film deposition on a flexible substrate because it crystallized well at low temperature below 90℃. The change in shielding characteristics depending on the Co content of the BaNi_(2-x)Co_xFe₁₆O₂₇ thin film was investigated, and excellent shielding characteristics with S21 of -1 dB were obtained in a wide frequency range of 26~40 GHz when the Co content was 0.4 or more. The purpose of this study is to analyze changes in shielding properties caused by change in Co content in relation to phase changes in BaNi_(2-x)Co_xFe₁₆O₂₇ and obtain basic data for developing excellent flexible electromagnetic wave shielding materials.

The advantage of OTFT technology is that large-area circuits can be manufactured on flexible substrates using a lowcost solution process such as inkjet printing. Compared to silicon-based inorganic semiconductor processes, the process temperature is lower and the process time is shorter, so it can be widely applied to fields that do not require high electron mobility. Materials that have utility as electrode materials include carbon that can be solution-processed, transparent carbon thin films, and metallic nanoparticles, etc. are being studied. Recently, a technology has been developed to facilitate charge injection by coating the surface of the Al electrode with solution-processable titanium oxide (TiOx), which can greatly improve the performance of OTFT. In order to commercialize OTFT technology, an appropriate method is to use a complementary circuit with excellent reliability and stability. For this, insulators and channel semiconductors using organic materials must have stability in the air. In this study, carbon-doped Mo (MoC) thin films were fabricated with different graphite target power densities via unbalanced magnetron sputtering (UBM). The influence of graphite target power density on the structural, surface area, physical, and electrical properties of MoC films was investigated. MoC thin films deposited by the unbalanced magnetron sputtering method exhibited a smooth and uniform surface. However, as the graphite target power density increased, the rms surface roughness of the MoC film increased, and the hardness and elastic modulus of the MoC thin film increased. Additionally, as the graphite target power density increased, the resistivity value of the MoC film increased. In the performance of an organic thin film transistor using a MoC gate electrode, the carrier mobility, threshold voltage, and drain current on/off ratio (I_on/I_off) showed 0.15 cm²/V·s, -5.6 V, and 7.5×10⁴, respectively.

The effects of the annealing temperature on the structural, morphological, and luminescent properties of SrWO₄:Sm³⁺ thin films grown on quartz substrates by radio-frequency magnetron sputtering were investigated. The thin films were annealed at various annealing temperatures for 20 min in a rapid thermal annealer after growing the thin films. The experimental results showed that the annealing temperature has a significant effect on the properties of the SrWO₄:Sm³⁺ thin films. The crystal structure of the as-grown SrWO₄:Sm³⁺ thin films was transformed from amorphous to crystalline after annealing at 800℃. The preferred orientation along (112) plane and a significant increase in average grain size by 820 nm were observed with increasing the annealing temperature. The average optical transmittance in the wavelength range of 500~1,100 nm was decreased from 72.0% at 800℃ to 44.2% at an annealing temperature of 1,000℃, where the highest value in the photoluminescence intensity was obtained. In addition to the red-shift of absorption edge, a higher annealing temperature caused the optical band gap energy of the SrWO₄:Sm³⁺ thin films to fall rapidly. These results suggest that the structural, morphological, and luminescent properties of SrWO4:Sm3+ thin films can be controlled by varying annealing temperature.

The effect of sputtering power on the amorphous Ga₂O₃ thin film deposited using the radio frequency sputtering system was evaluated. Amorphous Ga₂O₃ is cheaper and more efficiently fabricated than crystalline Ga₂O₃, and is studied in various fields such as RRAM, photodetector, and flexible devices. In this study, amorphous Ga₂O₃ was deposited by radio frequency sputtering system and represented a transmittance of over 80% in the visible light region and a homogeneous and dense surface. The optical band gap energy decreased as the sputtering power increased owing to the quantum size effect. Thus, the specific band gap of amorphous Ga₂O₃ can be obtained by adjusting the sputtering power, it indicates amorphous Ga₂O₃ can be used in various fields.

In recent years, the transparent amorphous oxide thin film transistor represented by indium-gallium-zinc-oxide (IGZO) has become the first choice of the next generation of integrated circuit control components. This article contributes an overview of IGZO thin-film transistors (TFTs), including their fundamental principles and recent advancements. The paper outlines various TFT structures and places emphasis on the fabrication process of the active layer. The result showed that the size of the active layer including the length-to-width ratio and the width could have a significant effect on the mobility. And the process of TFT could influence the crystal structure of IGZO thin film. Furthermore, the article presents an overview of recent applications of IGZO TFTs, such as their use in display drivers and TFT memories. At last, the future development of IGZO TFT is forecasted in this paper.

In this study, the heteroepitaxial thin film growth of β-Ga₂O₃ was studied according to the position of the susceptor in mist-CVD. The position of the susceptor and substrate was moved step by step from the center of the hot zone to the inlet of mist in the range of 0~50 mm. It was confirmed that the average thickness increased to 292 nm (D1), 521 nm (D2), and 580 nm (D3) as the position of the susceptor moved away from the center of the hot zone region. The thickness of the lower region of the substrate is increased compared to the upper region. The surface roughness of the lower region of the substrate also increased because the nucleation density increased due to the increase in the lifetime of the mist droplets and the increased mist density. Therefore, thin film growth of β-Ga₂O₃ in mist-CVD is performed by appropriately adjusting the position of the susceptor (or substrate) in consideration of the mist velocity, evaporation amount, and temperature difference with the substrate, thereby determining the crystallinity of the thin film, the thickness distribution, and the thickness of the thin film. Therefore, these results can provide insights for optimizing the mist-CVD process and producing high-quality β-Ga₂O₃ thin films for various optical and electronic applications.

Gallium oxide (Ga₂O₃) thin films were grown on c-, a-, m-, r-plane sapphire substrates using a mist chemical vapor deposition system. Various growth temperature range of 400~600℃ was applied for Ga₂O₃ thin film deposition. Then, several structural properties were characterized such as film thickness, crystal phase, lattice orientation, surface roughness, and optical bandgap. Under the certain growth temperature of 500℃, all grown Ga₂O₃ featured rhombohedral crystal structures and well-aligned preferred orientation to sapphire substrate. The films grown on c-and r-plane sapphire substrates, showed low surface roughness and large optical bandgap compared to those on a-and m-plane substrates. Therefore, various sapphire orientation can be potentially applicable for future Ga₂O₃-based electronics applications.

The quench voltage of the second-generation superconducting wire is affected by the resistivity characteristics of the stabilization layer. The specific resistance of the stabilization layer can be changed by the deposition process using RF magnetron sputtering. In this paper, a thin film made of a homogeneous material (Ag) and a dissimilar material (Cu) was deposited on the stabilization layer of the second-generation superconducting wire through RF magnetron sputtering. We found that the specific resistance was reduced by increasing the thickness of the stabilization layer. The reduction in the resistivity of the stabilization layer led to a decrease in the quench voltage of the second-generation superconducting wire. We suggest that various characteristic changes of the second-generation superconducting wire can be expected through the successful change in the resistivity of the stabilization layer of the proposed deposition process.

AGZO thin films were deposited on glass substrates using RF magnetron sputtering system under Ar flow rates, and their structural, electrical, and optical properties were analyzed systematically. As a result of the XRD pattern, the peak of the (002) (2θ≈33.7˚) orientation was observed, and it was found to have a hexagonal wurtzite structure. The sheet resistance of Ar 5 sccm was 3.073×10² Ω/sq and showed the best electrical properties because of the improvement of mobility due to the increase of the grain size and the variation of RMS roughness. In addition, the average transmittance was more than 90% for all samples, which demonstrated good optical properties. It is expected that the TCO characteristics can be improved by controlling Ar flow rates, and this will increase the efficiency of photoelectronic devices such as OLED and solar cells.

We fabricated BiAlO thin film by a solution process with a brush coating to be used as liquid crystal (LC) alignment layer. Solution-processed BiAlO was coated on the glass substrate by brush process. Prepared thin films were annealed at different temperatures of 80℃, 180℃, and 280℃. To verify whether the BiAlO film was formed properly, X-ray photoelectron spectroscopy analysis was performed on Bi and Al. Using a crystal rotation method by polarized optical microscopy, LC alignment state was evaluated. At the annealing temperature of 280℃, the uniform homogenous LC alignment was achieved. To reveal the mechanism of LC alignment by brush coating, field emission scanning electron microscope was used. Through this analysis, spin-coated and brush coated film surface were compared. It was revealed that physical anisotropy was induced by brush coating at a high annealing temperature. Particles were aligned in one direction along which brush coating was made, resulting in a physical anisotropy that affects a uniform LC alignment. Therefore, it was confirmed that brush coating combined with BiAlO thin film annealed at high temperature has a significant potential for LC alignment.

Indium-doped Mg_0.05Zn_0.95O thin films were deposited on glass substrates by a sol-gel method. Three types of indium precursors such as indium chloride, indium acetate, and indium nitrate were used as doping sources. Physical properties of fabricated thin films were analyzed through XRD (x-ray diffraction), UV-vis spectrophotometer, Hall effect measurement, and EDS (energy dispersive x-ray spectroscopy). All In-doped thin films grown in this study exhibited a preferred orientation of (002) with over 80% transmittance. The results showed that the Mg_0.05Zn_0.95O thin film from indium chloride as the indium precursor has higher crystallinity and transmittance with lower resistivity when compared with those from other indium precursors.

a-Si is commonly considered as a primary candidate for the formation of passivation layer in heterojunction (HIT) solar cells. However, there are some problems when using this material such as significant losses due to recombination and parasitic absorption. To reduce these problems, a wide bandgap material is needed. A wide bandgap has a positive influence on effective transmittance, reduction of the parasitic absorption, and prevention of unnecessary epitaxial growth. In this paper, the adoption of a-SiO_x:H as the intrinsic layer was discussed. To increase lifetime and conductivity, oxygen concentration control is crucial because it is correlated with the thickness, bonding defect, interface density (D_it), and band offset. A thick oxygenrich layer causes the lifetime and the implied open-circuit voltage to drop. Furthermore the thicker the layer gets, the more free hydrogen atoms are etched in thin films, which worsens the passivation quality and the efficiency of solar cells. Previous studies revealed that the lifetime and the implied voltage decreased when the a-SiOx thickness went beyond around 9 nm. In addition to this, oxygen acted as a defect in the intrinsic layer. The D_it increased up to an oxygen rate on the order of 8%. Beyond 8%, the D_it was constant. By controlling the oxygen concentration properly and achieving a thin layer, high-efficiency HIT solar cells can be fabricated.

TFTs technologies with as high mobility as possible is essential for high-performance large displays. TFTs using nanocrystalline silicon thin films can achieve higher mobility. In this work, the change of the crystalline volume fraction at different hydrogen dilution ratios was investigated by depositing nc-Si:H thin films using PECVD. It was observed that increasing hydrogen dilution ratio increased not only the crystalline volume fraction but also the crystallite size. The thin films with a high crystalline volume fraction (55%) and a low defect density (10¹⁷ cm^-3·eV^-1) were used as top gate TFTs channel layer, leading to a high mobility (55 ㎠/V·s). We suggest that TFTs of high mobility to meet the need of display industries can be benefited by the formation of thin film with high crystalline volume fraction as well as low defect density as a channel layer.

The transfer characteristics of amorphous indium gallium zinc oxide thin film transistor (a-IGZO TFT) showed the distortion in the subthreshold region after gate bias stress, in addition to the parallel shift of threshold voltage. The capacitancevoltage (C-V) curve was also deformed from its initial shape after the gate bias stress. This study analyzes both the C-V and transfer curves plotted on the same gate voltage axis in order to investigate the mechanism driving the distortion in the transfer curve. It is deduced that an additional interfacial trap states at the bottom interface of a-IGZO are produced during gate bias stress, thereby they exhibit the back channel effect, which explains the origin of the distortion in the transfer curve and the deformation of C-V curve.

In this paper, we investigated the surface properties of polymer insulators to improve electrical insulation performance. First, after washing the polymer insulator in various ways, its contact angle was increased, thereby improving the hydrophobic properties and electrical insulation properties. In addition, TiO₂ thin films, which have been used as a photocatalytic material and have been applied to the polymer insulator surface of to enhance the surface and electrical insulating properties. For the sputtering method, the contact angle after coating the TiO₂ thin film increased with increasing RF power, but it was lower compared to that before coating, indicating that the hydrophobic properties of the surface were slightly deteriorated. Consequently, the electrical properties of the polymer-insulating material were maintained or improved after the TiO₂ thin-film coating.

As packaging processes for atomic gyroscope vapor cells, the glass tube tip-off process, anodic bonding, and paste sealing have been widely studied. However, there are stability issues in the alkali metal which are caused by impurity elements and leakage during high-temperature processes. In this study, we investigated the applicability of a vapor cell low-temperature packaging process by depositing Au on a Pyrex cell in addition to forming an Au-Sn thin film on a cap to cover the cell, followed by laser irradiation of the Au/Au-Sn interface. The mechanism of the thin film bonding was evaluated by XRD, while the packaging reliability of an Ne gas-filled vapor cell was characterized by variation of plasma discharge behavior with time. Furthermore, we confirmed that the Rb alkaline metal inside the vapor cell showed no color change, indicating no oxidation occurred during the process.