Polymer nanocomposites incorporating inorganic nanofillers have emerged as highly promising electromagnetic interference (EMI) shielding materials, combining mechanical compliance with robust conductive percolation networks. Carbon nanotubes (CNTs) are particularly attractive as conductive fillers because their high aspect ratio facilitates percolation at low loadings. Also, CNTs offer superior mechanical durability under deformation compared to rigid, fracture-prone metal nanowires. For EMI shielding, high electrical conductivity is critical as it enhances both reflection and absorption through efficient charge dissipation and conduction losses. However, achieving highly aligned conductive pathways without degrading the intrinsic electrical properties of CNTs remains a significant challenge. Here, we demonstrate a non-destructive magnetic surface-functionalization and alignment strategy. Using a polydopamine (PDA)-mediated route, pristine multiwalled CNTs are uniformly decorated with Fe₃O₄ nanoparticles (FMWCNTs). This enables highly effective magnetic field-driven alignment at fields as low as 10 mT, promoting the strategic formation of percolation networks. By optimizing the Fe₃O₄/MWCNT ratio for high saturation magnetization and uniform coverage, the aligned FMWCNTs exhibit significant electrical anisotropy, delivering a 10.7-fold higher electrical conductivity in the parallel configuration compared to the vertical configuration. These findings present a scalable, room-temperature platform for engineering directionally enhanced conductivity in polymer nanocomposites, with broad applicability in advanced EMI shielding, flexible electronics, and advanced packaging technologies.

Citations

• Interfacial Engineering of Composite Piezoelectric Fibers Via an Anchor-Chain Architecture
  Jun Liu, Qiao Zhou, Pengcheng Zhang, Shuying Hu, Fang Zhou, Shuangshuang Ren, Ting Guo, Leiying Miao
  ACS Applied Engineering Materials.2026; 4(8): 4367.     CrossRef

β-Ga₂O₃ is an ultra-wide bandgap semiconductor promising for high-power electronic applications; however, heteroepitaxial growth on sapphire is challenging lattice and symmetry mismatch. In this study, β-Ga₂O₃ thin films were grown on C-plane sapphire substrates with various off-axis angles (0–12°) using mist-CVD, and the influence of substrate miscut on structural and optical properties was investigated. All films grown at 900°C exhibited (-201) oriented β phase. The crystal quality was strongly dependent on the off-axis angle, with intermediate off-axis angles (Δ_a = 6–8°) showing the narrowest rocking curve width. Off-axis substrates promoted step-aligned growth behavior compared to on-axis growth. Optical measurements revealed enhanced transmittance and wider bandgap values (4.92–4.95 eV) for off-axis samples compared to the on-axis film (4.69 eV). The findings provide practical guidelines for optimizing heteroepitaxial β-Ga₂O₃ growth on low-cost sapphire substrates for high-performance device applications.

The potential of replacing crosslinked polyethylene (XLPE) with an eco-friendly alternative, polypropylene (PP), as insulating material is investigated for overhead power distribution lines. Although XLPE exhibits excellent electrical and mechanical properties, the byproducts generated during crosslinking pose environmental challenges. PP is a viable alternative because of recyclability and absence of byproducts during crosslinking. This study evaluated alternating current (AC) breakdown strength, contact angle, and tracking resistance of two commercially available XLPE samples and three types of PP (PP1, PP2, PP3) with varying additive content. AC breakdown strength, analyzed using the Weibull distribution, facilitated relative comparison of insulation performance. PP2 exhibited scale parameters comparable to or exceeding those of XLPE. Contact angles exceeding 90° displayed hydrophobicity across all samples. To address pass/fail evaluation limitations, arcing images from tracking tests were analyzed using the box-counting method for fractal dimension analysis. Fractal dimensions increased with arcing extent, and complexity increased with test duration. Tracking resistance performance order was PP3, PP1, CC, PP2, OC which was attributed to enhanced heat dissipation properties of filler additives. The proposed quantitative method for comparing tracking resistance through fractal dimension analysis, explored the feasibility of using PP insulating materials in overhead power distribution lines.

The increasing global demand for renewable energy has accelerated the deployment of offshore wind farms, thereby highlighting the need for advanced development and performance assessment techniques for dynamic submarine cables used in floating offshore wind systems. These cables are continuously subjected to combined thermal, electrical, and mechanical stresses, with mechanical loading playing a particularly dominant role. As a result, dynamic submarine cables exhibit degradation behaviors that differ significantly from those of conventional fixed submarine cables. This paper presents the design and implementation of a comprehensive evaluation system capable of applying combined thermal, electrical, and mechanical stresses to dynamic submarine cables. The system was validated using a 66 kV wet type submarine cable through commissioning tests and insulation performance measurements. Electrical stress of 72 kV, thermal stress exceeding 95°C, and mechanical stress corresponding to a bending radius of 20 times the cable diameter over 20 cycles were applied to verify system reliability. The subsequent insulation assessments quantitatively confirmed performance variations induced by the combined stresses. The results demonstrate that the proposed platform is the first system capable of simultaneously applying thermal, electrical, and mechanical stresses to dynamic submarine cables, and its operational performance has been successfully validated. This platform enables realistic reliability evaluation of dynamic cables used in floating offshore wind farms and is expected to improve the overall operational reliability of offshore wind power systems.

The rapid proliferation of artificial intelligence (AI) servers and high-performance computing systems has significantly elevated the technical and reliability requirements for multilayer ceramic capacitors (MLCCs). In such systems, MLCCs are critical passive components that must deliver high capacitance, fast transient response, and robust insulation performance under high temperature, voltage, and current density. This review examines the material, structural, and process innovations that underpin MLCC performance in AI applications. Key topics include the development of ultrathin dielectric layers (<0.5 μm), rare-earth doped BaTiO₃-based dielectrics with enhanced DC bias stability, and core-shell microstructures designed for temperature and field resilience. The paper also explores insulation degradation mechanisms―such as vacancydriven conduction and demixing―and advanced reliability assessment methodologies, including HALT, TSDC, and the tipping point framework. Comparisons with automotive-grade MLCCs highlight the unique requirements of AI systems, such as ultraminiaturization, high volumetric efficiency, and ppm-level field failure rates. Finally, the review discusses emerging trends in MLCC technology, including particle engineering, interface stabilization, and advanced lamination techniques, and provides insight into the future direction of capacitor development tailored to AI data center environments.

Citations

• Reliability enhancement in Dy-doped BaTiO3 nanoceramics: from core–shell structure to phase-field modeling
  Shuyan Huang, Xinjie Wang, Mengjian Xiao, Xu Cheng, Xiaohui Wang
  Journal of Materials Science.2026; 61(37): 27665.     CrossRef
• Key factors determining high-temperature operating lifetime of multilayer ceramic capacitors (MLCCs)
  Yuto Tomura, Tzu-han Weng, Yusuke Oba, Tomohiro Kajita, Daiki Ishii
  Japanese Journal of Applied Physics.2026; 65(16): 16SP05.     CrossRef
• Effect of BaZrO3 Addition on the Frequency and Temperature Dependent Dielectric Properties of BaTiO3-Based Ceramics
  Won-Su Lee, Jong Kyu Lee, Moon-Taek Cho, Jung Rag Yoon
  Journal of Electrical and Electronic Materials.2026; 39(5): 478.     CrossRef
• Manufacturing Process Optimization of Oxide-Based Multilayer Ceramic Batteries Using Multilayer Ceramic Processing Technologies
  Won-Su Lee, Jong Kyu Lee, Jung Rag Yoon
  Journal of Electrical and Electronic Materials.2026; 39(5): 519.     CrossRef

Ceramic thin plates are widely utilized in various advanced technologies, such as fuel cells and heat dissipation substrates, due to their high mechanical strength and thermal conductivity. However, the trend of thinning ceramic plates increases warpage, which can critically affect product quality and reliability. Therefore, understanding and accurately measuring this warpage has become increasingly important. In this study, a non-contact measurement method, the light sectioning technique, was applied to measure the warpage of thin ceramic plates with a half-cell (anode/electrolyte) structure for solid oxide fuel cells (SOFC) by varying their area and thickness. The relationship between the physical properties of the thin plates and the warpage was analyzed. Additionally, a comparative analysis was conducted to evaluate warpage errors caused by compressive loads during the traditional contact measurement process. Finally, to verify the reliability of the non-contact measurement method, four types of non-contact measurement techniques - light sectioning technique, laser displacement measurement, optical confocal technique, and white-light interferometry technique - were used to compare warpage data by orientation. The results were also compared with those from contact measurement methods to analyze the average warpage values. Through this, the superiority and high reliability of the non-contact measurement method were demonstrated.

κ-phase Ga₂O₃ is a wide-bandgap semiconductor that has attracted attention for power and optoelectronic device applications. However, its crystal quality and optical properties are highly dependent on the growth temperature, which motivates the need for a systematic study. In this work, κ-Ga₂O₃ thin films were grown on AlN/sapphire templates using mist-CVD at different temperatures. At lower temperatures (400℃), films exhibited incomplete crystallization and partial opacity, whereas higher growth temperatures (500-700℃) produced transparent films with improved properties. The bandgap was found to increase with temperature, consistent with reported values for 600-700℃, and XRD/XRC analysis confirmed that crystal quality improved with higher growth temperature. AFM analysis further revealed reductions in surface roughness and grain size variation at elevated temperatures. These findings indicate that an optimal growth window of 600-700℃ enables high-quality κ-Ga₂O₃ films, with potential implications for integrating this material on other hexagonal substrates such as SiC and GaN.

Citations

• Growth of Beta-Phase Gallium Oxide Thin Films on Off-Axis Sapphire Substrates by Mist Chemical Vapor Deposition
  Jae-Hyeok Lim, Tae-Yong Park, Yun-Ji Shin, Seong-Min Jeong, Chang-Mo Kang, Si-Young Bae
  Journal of Electrical and Electronic Materials.2026; 39(3): 302.     CrossRef

To ensure the long-term reliability of flexible photovoltaic (FPV) modules, it is crucial to develop an effective moisture barrier layer that prevents the infiltration of moisture and oxygen. We developed such a layer composed of parylene (700 nm) and AlOx (70 nm), optimizing its material properties, moisture-blocking performance, and processing conditions. The barrier layer applied to the Ethylene Tetrafluoroethylene (ETFE) substrate demonstrated a water vapor transmission rate (WVTR) of 6.33 × 10^-2 g/m²/day and an average visible light transmittance (AVT) of 85.3% over the 380-780 nm wavelength range. For the FPV module with this barrier, Damp/Heat (DH) reliability testing was conducted at 85℃ and 85% relative humidity for up to 1,000 hours. During testing, the power conversion efficiency (PCE) decreased slightly from 25.4% (0 hr) to 24.7% (1,000 hr), reflecting a minimal reduction of only 0.7%. The primary cause of degradation was identified as a -4% relative change in shortcircuit current density (JSC) before and after DH testing. Consequently, the ETFE/parylene/AlOx multilayer moisture barrier proved highly effective in ensuring the long-term reliability of solar modules.

Understanding the structure-property relationship in functional materials is crucial as microstructural features such as nano-precipitates, phase boundary, grain boundary segregation, and grain boundary phases play a key role in their functional properties. Atom probe tomography (APT) is an advanced analytical technique that allows for the three-dimensional (3D) mapping of atomic distributions and the precise determination of local chemical compositions in materials. Moreover, it offers sub-nanometer spatial resolution and chemical sensitivity at the tens of parts per million (ppm) level. Owing to its unique capabilities, this technique has been employed to uncover the 3D elemental distributions in a wide range of materials, including alloys, semiconductors, nanomaterials, and even biomaterials. In this paper, various kinds of examples are introduced for elucidating structure-property relationships on functional materials by utilizing the atom probe tomography.

Precise control over the morphology of nanostructures is critical for tailoring their physical and chemical properties. This study addresses the challenge of developing a simple, integrated method for synthesizing both 1D and 2D colloidal Cu nanostructures in a single system, achieving successful tuning of their localized surface plasmon resonance (LSPR) properties. A facile hydrothermal synthesis utilizing potassium iodide (KI) and hexadecylamine (HDA) is presented for controlling Cu nanostructure morphologies. The key to achieving 1D nanowires (NWs) and 2D nanoplates (NPs) depends on the controlled adsorption of HDA molecules and iodide (I-) ions on specific crystal facets. Depending on the morphologies, the resultant Cu nanostructures exhibit tunable LSPR peaks from 558 nm [nanoplates (NPs)] to 590 nm [nanowires (NWs)]. These results pave the way for the scalable and cost-effective production of plasmonic Cu nanostructures with tunable optical properties, holding promise for applications in sensing, catalysis, and photonic devices.

Citations

• Complexation-controlled Cu@Ag core-shell flakes for thermally stable printed electrodes in flexible energy-storage capacitors
  Seokhwan Kim, Geumseong Lee, Ye Chan Lee, Je-Hui Koo, Seonhwa Park, Geon-Tae Hwang, Mahesh Peddigari, Jungho Ryu, Dahye Shin, Kyoung Jin Jung, Kwi-Il Park, Yuho Min
  Chemical Engineering Journal.2026; 540: 177341.     CrossRef

Climate conditions, especially transport and storage, are a very important factor in the process of sampling and testing insulation oil in the field. The samples of insulating oil exposed to the atmosphere affect the dielectric strength, total acid number and moisture test value by oxygen and high humidity environment and may also affect the results according to the criteria specified in each test. Therefore, reliable test values for insulating oil testing require consideration of the atmospheric environment of the test site, including oxygen and humidity. In this paper, each test was conducted on insulating oil exposed to various time and humidity environments, and the effect of the atmospheric environment on the test results was analyzed by comparing and analyzing with the first insulating oil.

Piezoelectric ceramics play an important role in various electronic applications. However, traditional ceramics are difficult to be used in some complicated structures, due to their low flexibility and high brittleness. To solve this problem, this study prepared and investigated ceramic/polymer composites that can utilize a good flexibility of polymers. Polyvinylidene fluoride-trifluoroethylene (PVDF-TrFE) and 0.77(Bi_1/2Na_1/2)TiO₃-0.23SrTiO₃ (BNST23) ceramics were selected to fabricate the composites. Ceramic/polymer composites were prepared using various volume fractions of BNST23 ceramics. The distribution of piezoceramic particles in BNST23/PVDF-TrFE composites was investigated using optical microscopy (OM) and scanning electron microscopy (SEM). The dielectric and piezoelectric properties of the composites were significantly influenced by the volume fraction of the piezoelectric ceramics. As a result, the highest piezoelectric constant (d33) of 56 pC/N was obtained in a composites with 70% volume fraction of BNST23 ceramics. Accordingly, it is expected that BNST23/PVDF-TrFE composites can be applied to various sensor applications.

In this paper, the electrical properties of liquid insulating oil were analyzed by changing the ambient temperature change at 10℃ in-tervals from 0℃ to 30℃ through an insulation breakdown experiment in order to analyze the insulation performance of liquid in-sulating oil that varies according to temperature changes. As a result, it was confirmed through experiments that the lower the am-bient temperature, the higher the insulation breakdown voltage, depending on both the electrode shape and the electrode interval, and it was determined that the lower the ambient temperature, the higher the insulation performance of the liquid insulating oil.

Piezoelectric ceramics play an important role in electrical and electronic devices such as sensors, actuators, and microelectronic devices. However, traditional ceramics are difficult to be used in various process industries due to their high brittleness and low flexibility. Therefore, piezoelectric paint sensors have been designed for application to the curved surfaces of complicated structures. Furthermore, recently, significant attention has been focused on the development of paint sensors that can be used as structure health monitoring sensors for vibration, impact, and acoustic emission. Several studies have successfully demonstrated the possibility that smart paint sensors can take the place of traditional ceramic sensors. In this review, we briefly introduce the concept of the piezoelectric paint sensors and the expected application field as well as their preparation and history.

The templated grain growth (TGG) method has gained significant attention for its ability to produce highly textured piezoelectric ceramics with significantly enhanced performance, making it a promising method for transducer and actuator applications. However, the texturing process using the TGG method requires the optimization of multiple steps, which can be challenging for beginners in this field. Therefore, in this tutorial, we provide an overview of the TGG method mainly based on our previous published works, including its various processing steps such as synthesizing anisotropic-shaped templates with size and size distribution control using the molten salt synthesis technique, tape casting, and identifying key factors for proper alignment of the templates in the target matrix system. Our goal is to provide a resource that can serve as a basic reference for researchers and engineers looking to improve their understanding and utilization of the TGG method for producing textured piezoelectric ceramics.

In this paper, in order to analyze high electrical insulation and cooling performance using mineral oil, the liquid insulating oil was changed in electrode shape and distance between electrodes to compare and analyze electrical characteristics according to equal electric field, quasi-equivalent electric field, and unequal electric field. As a result, the breakdown voltages were 36,875 V and 36,875 V in the form of sphere-sphere and plate-plate electrodes with equal electric fields. The breakdown voltage was 31,475 V in the sphere-plate electrode type, which is a quasi-equilibrium field, and the breakdown voltage was 28,592 V, 27,050 V, and 22,750 V in the needle-needle, sphere-needle, and needle-plate electrode types, which are unequal fields. Through this, it is possible to know the difference in breakdown voltage according to the type of electric field. The more equal the field, the higher the breakdown voltage, and the more unequal field, the lower the breakdown voltage. The difference in insulation breakdown voltage could be seen depending on the type of electric field, the insulation breakdown voltage was higher for the more equal electric field, and the insulation breakdown voltage was lower for the more unequal electric field. Also, it was confirmed that the closer the distance between the electrodes, the higher the insulation breakdown voltage, the higher the insulation breakdown current, and the insulation breakdown voltage and the insulation breakdown current were proportional.

Heaters using the resistance heating principle are used in various industrial fields that require heat and are also essentially used in bidet among small home appliances. A planar heater and a coil-inserted heater mounted on a conventional commercially used bidet have disadvantages and limitations of complicated manufacturing process and local heating. In this study, silver-palladium (Ag-Pd) powder material was used for a screen-printing process that is more advantageous in achieving simplification than the existing process, and a rod-type heater for bidet was manufactured. The on-off cycle test under actual conditions was conducted to confirm the durability and the capability of the fabricated heater, and the fabricated heater operated more than 2,600 on-off cycles, which means it could be applied for a commercial product. In addition, through the on-off cycles under harsh conditions, the cause of failure was identified after the test that the durability limit temperature of the heater was 850℃. Through Ag-Pd rod heater in this study, it is expected to contribute to the efficient development of electrode materials for heaters and the improvement of the durability of heaters in the future.

Magnetoelectric (ME) properties of 3-0 type particulate composites have been investigated with respect to application features for reliable magnetic sensitivity and magnetically-induced output voltage. In order to figure out the magnetoelectric characteristics in the ME composites, frequency dependent ME responses were studied from [0.948 Na0.5K0.5NbO3-0.052 LiSbO₃]-[Co_1-xZn_xFe₂O₄] (NKNLS)/Co_1-xZn_xFe₂O₄ (CZFO, x=0, 0.1, and 0.2). As a result, the maximal αME of 23.15 mV/cm·Oe was achieved from the NKNLS-CZFO (x_Zn = 0.1) composites at resonance frequency of 315 kHz and H_dc = 0 Oe. From the frequency dependent ME responses, it is clearly described that the self-biased ME composites can be used for applications as both magnetic sensors and energy harvesters, respectively.

Global warming is accelerating due to the use of fossil fuels that have been used continuously for centuries. Now, humankind recognizes its seriousness, and is conducting research on searching for eco-friendly and sustainable energy. In the field of solar energy, which is a kind of eco-friendly and sustainable, many studies are being conducted to enhance the output performance of the module. In this study, the output improvement for the shingled module structure was studied. In order to improve the output performance of the module, the thickness of the encapsulant was increased, and the lamination process conditions have been improved accordingly. After that, the crosslinking rate was analyzed, and the suitability of the lamination process conditions was judged using this. In addition, a peeling test was conducted to analyze the correlation between the adhesion of the encapsulant and the output performance of the module. Finally, the optimization for the encapsulant material and the lamination process conditions for high-power shingled modules was established, and accordingly, the market share of high-power shingled modules in the solar module market can be expected to rise.

For the last decades, a research hotspot for the halide perovskites (HPs) is now showing great progress in terms of improving efficiency for numerous photovoltaic devices (PVDs). However, it still faces challenges in the case of long-term stability in the air atmosphere. Defect-free high-quality HP single crystals show their promising properties for the remarkable development of highly efficient and stable PVDs. Here, we summarize the growth processing routes for the stable HP single crystals as well as briefly discuss the pros and cons of those well-established synthesis routes. Furthermore, we briefly include the comparison note between the HP single crystals and polycrystalline perovskite films regarding their device applications. Based on the future progress, the review concludes subjective perspectives and current challenges for the development of HPs high-quality PVDs.

Since 2010, polymer-based magnetoelectric (ME) composites have been developed with detailed investigations of multiferroic properties such as piezoelectric, magnetostrictive, and magnetoelectric, etc. In particular, as a piezoelectric polymer, poly(vinylidene fluoride) and its co-polymers have been widely used in ME composites for energy harvesting, health monitoring, environment treatment, and bio-medical applications. In this study, main research trend and selected experimental results of polymer-based ME composites are briefly reviewed with respect to composite structure as well as application field. A conclusion was drawn that the polymer-based ME composites would be feasible as flexible devices or functional membranes in the near future.

Inorganic-organic hybrid perovskite solar cells have demonstrated considerable improvements, reaching 25.5% of certified power conversion efficiency in 2020 from 3.8% in 2009. In normal structured perovskite solar cells, TiO₂ electrontransporting materials require heat treatment process at a high temperature over 450℃ to induce crystallinity. Inverted perovskite solar cells have also been studied to exclude the additional thermal process by using [6,6]-phenyl-C₆₁-butyric acid methyl ester (PCBM) as a non-oxide electron-transporting layer. However, the drawback of the PCBM layer is a charge accumulation at the interface between PCBM and a metal electrode. The impact of bathocuproin (BCP) buffer layer on photovoltaic performance has been investigated herein to solve the problem of PCBM. 2-mM BCP-modified perovskite solar cells were observed to exhibit a maximum efficiency of 12.03% compared with BCP-free counterparts (5.82%) due to the suppression of the charge accumulation at the PCBM-Au interface and the resulting reduction of the charge recombination between perovskite and the PCBM layer.

Copper-chromium alloys have been used as contact materials of vacuum interrupters in circuit breakers, but new materials with highly stable performance are required to break the high voltage and high current barrier due to the recent increase in breaking capacity. In this paper, a new contact material was fabricated from a ternary alloy instead of existing Cu-Cr alloys. Its breaking performance and endurance were verified from a synthetic test and compared with that of various contact materials. The test results verified that the breaking performance of the new contact material was excellent.

Although waste oil derived fuel (WDF) production technology was developed under a government initiative ~10 years ago, it became stagnant owing to the small size of participating companies, residents’ rejection of foul odor, and the nature of the technology for recycling waste that was avoided. However, this subject is under the spotlight again because of recent developments, such as garbage crisis. In particular, plastic is the most difficult waste to dispose of, with more than 4 million tons of plastic waste produced every year according to statistics from the Ministry of Environment. The most effective method for treating plastic waste is to produce WDF through low temperature thermal decomposition. The WDF includes several volatile ingredients that mostly limit the use of fuel for boilers, owing to safety concerns. In particular, flash point is legally stipulated because of secondary contamination in the distribution process and the risk of fire and explosion. It is required that external shipments (distribution) should be maintained in the range of at least 30~60℃ (excluding explosion prevention facilities) for diesel power generation. Therefore, this study seeks to find the flash point that is best suited to WDFs produced from plastic waste.

Inorganic-organic hybrid perovskite solar cells have demonstrated a significant achievement by reaching a certified power conversion efficiency of 25.2% in 2019 as compared to that of 3.8% in 2009. However, organic hole conductors such as PTAA and spiro-OMeTAD are known to be expensive and unstable when they are exposed to operational conditions. In this study, the inorganic hole conductor CuSCN was used to overcome such concerns. The influence of dipropyl sulfide (DPS) and diethyl sulfide (DES) as CuSCN deposition solvents on the underlying perovskite active layer was investigated. DES solvent was observed to be advantageous in terms of CuSCN solubility and mild for the perovskite layer, thereby resulting in a power conversion efficiency of 16.9%.

A fire, be it caused intentionally or unintentionally, leads to economic loss and physical damage, and requires digestion. The number of fires is increasing yearly, and electrical fires account for more than 30% among the main causes of fires. Electric wires that catch fire typically employ silicone coatings; silicone has organic as well as inorganic properties. Silicon is a natural, nonexistent, synthetic product with numerous applications. In this study, a silicon rubber for application in wires was prepared by high-temperature vulcanization (HTV) with a Shore A hardness of 70. We report results for the flame retardancy test and the fire safety characteristics via inorganic analysis. For this, a quartz inorganic material was added to the wire specimen, and 18% powdered extinguishing agent ammonium phosphate and expanded vermiculite respectively. Thus, expanded vermiculite showed the best flame retardancy and fire safety characteristics.

In this study, photoluminescence (PL) analysis was performed to evaluate the optical properties of commercial ZnO substrates. Particular attention was paid to the bound exciton (BX) luminescence, which is usually the strongest emission intensity of commercial substrates. At 15 K, PL analysis revealed that the BX peak due to donor-type impurities (donor-bound-exciton; DX) dominated, while two-electron satellite (TES) emission, donor-accepter pair (DAP) emission, and LO-phonon replica emission were also observed. The impurity concentration of the ZnO substrate was determined to be 10¹⁵ to 10¹⁶/cm³ by examination of the temperature variation of DAP, while the half width and intensity change of the luminescence revealed that the temperature change of BX can be interpreted almost the same as the analysis of free-exciton emission.

A multielectrode electronic paper film capable of expressing a single-color image was fabricated by injecting color electronic ink into an electronic paper panel; on the basis of its reflective or transparent properties, it is possible to control the expression of six single-color images and their transmittance. In this study, a single-color image was represented by driving a multielectrode electronic paper film; color coordinates were measured. The six capable single colors were yellowish pink (0.444, 0.354), white (0.355, 0.352), black (0.241, 0.241), orange (0.514, 0.360), reddish orange (0.606, 0.338), and reddish purple (0.469, 0.145). Color particles used in this paper were black and white, by which six colors are accomplished, but more single-color images can be combined by using cyan, magenta, and yellow particles.

Because of the rapidly changing environment and high uncertainties, the semiconductor industry is in need of appropriate forecasting technology. In particular, both the cost and time in the test process are increasing because the process becomes complicated and there are more factors to consider. In this paper, we propose a prediction model that predicts a final “good” or “bad” on the basis of preconditioning test data generated in the semiconductor test process. The proposed prediction model solves the classification and regression problems that are often dealt with in the semiconductor process and constructs a reliable prediction model. We also implemented a prediction model through various machine learning algorithms. We compared the performance of the prediction models constructed through each algorithm. Actual data of the semiconductor test process was used for accurate prediction model construction and effective test verification.

Citations

• Prediction and Optimization Model for Casting Process Defects with Proposed Process Variable Ranges
  Hui Su Lee, Ji Su Lim, So Young Baek, Doowon Choi
  Journal of Korean Society for Quality Management.2026; 54(2): 229.     CrossRef

3YSZ + (x) Al₂O₃ composites (x = 20, 40, 60, 80 wt%) were fabricated and the influences of particle sizes of Al₂O₃ on their microstructures and mechanical properties were investigated with XRD, SEM, vickers hardness and fracture toughness. Al₂O₃-3YSZ composites containing Al₂O₃ powder of a 0.3 μm and an 1.0 μm, which are here in after named as Al2O3(0.3 μm)-3YSZ and Al₂O₃ (1.0 μm)-3YSZ, respectively, were made by mixing raw materials, uni-axial pressing and sintering at 1,400℃, 1,500℃, and 1,600℃. Al₂O₃ (0.3 μm)-3YSZ composites show the higher density and the better mechanical properties than Al₂O₃ (1.0 μm)-3YSZ composites. The Vickers hardness of the Al₂O₃ (0.3 μm)-3YSZ composites show a peak value of 1,997 Hv at the content of 60 wt% Al₂O₃, which is a slightly higher value in comparison with 1,938 Hv of the Al2O3(1.0 μm)-3YSZ composite. However, the fracture toughness of Al₂O₃-3YSZ composites monotonically increases with decreasing the content of Al₂O₃ without any peak values. Al₂O₃ (0.3 μm)-3YSZ and Al₂O₃ (1.0 μm)-3YSZ composites sintered at 1,600℃ have a maximum value of a 6.9 MPa·m1/2 and a 6.2 MPa·m1/2, respectively at the composition of containing 20 wt% Al2O3. It should be noticed that the mechanical properties and the sintering density of the Al₂O₃-3YSZ composites can be enhanced by using more fine Al₂O₃ powder due to their denser microstructure and smaller grain size.

Citations

• Effectiveness of silicon nanoparticles on the mechanical, wear, and physical characteristics of PALF/sisal fiber–based polymer hybrid nanocomposites
  S. Mayakannan, J. Bensam Raj, V. L. Raja, M. Nagaraj
  Biomass Conversion and Biorefinery.2023; 13(14): 13291.     CrossRef