This paper proposes a circular sequential lighting control method to reduce current imbalance and luminance deviation among multiple LED modules in AC-powered LED lighting systems. Conventional fixed-sequence lighting control repeatedly prioritizes the same LED modules in every rectified voltage cycle, which leads to unequal current distribution, luminance non-uniformity, and the accelerated degradation of specific modules during long-term operation. To address these limitations, a circular sequential lighting strategy is introduced, in which the lighting order is cyclically rotated at every rectified cycle, ensuring that all LED modules experience equal lighting opportunities. A prototype AC-LED lighting system consisting of four series-connected LED modules was implemented and experimentally evaluated. The results demonstrate that, while the conventional fixed-sequence method produces a maximum average current deviation of up to 1.6 mA among modules, the proposed method equalizes the average current across all modules to approximately 17.1 mA. Furthermore, the flicker index remains at 0.13, which is comparable to that of the conventional method, indicating that luminance uniformity is improved without degradation of optical performance. The proposed circular sequential lighting control effectively distributes electrical stress, enhances luminance uniformity, and improves long-term reliability, making it a practical and efficient solution for high-quality AC-LED lighting applications.

Long lifetime, low power consumption, and environmental friendliness have enabled light-emitting diode (LED) lighting to rapidly replace conventional light sources such as incandescent and fluorescent lamps. In particular, AC-LED lighting systems can be directly powered by commercial alternating current (AC) sources; however, they suffer from significant luminance deviation caused by uneven current distribution among LED light-emitting modules. This paper proposes a lighting control method that improves flicker performance while maintaining lamp brightness and effectively reduces luminance deviation in AC-LED lighting. The proposed method reduces luminance deviation by controlling the lighting order of multiple LED light-emitting modules. Among four LED modules, only the required number of modules is continuously turned on, and the lighting priority alternates between rectification cycles. Specifically, during odd rectification cycles, LED modules are activated sequentially in ascending order (11→12→13→14), whereas during even rectification cycles, they are activated in descending order (14→13→12→11). By alternately applying continuous lighting control with opposite activation orders, the proposed reverse alternating lighting control method equalizes the current distribution among LED modules. As a result, luminance uniformity is improved, electrical stress concentration on specific modules is reduced, and the operational lifetime of the LED modules is extended compared with the conventional fixed-sequence lighting control method.

Human-centric lighting (HCL) aims to enhance well-being and performance by tailoring lighting to human needs. However, LED flicker-rapid brightness changes-remains a critical issue, causing discomfort and reduced productivity. This paper addresses flicker problems in living and industrial spaces with LED lighting. We propose solutions to mitigate flicker by examining causes like power supply variations and LED driver design. Techniques such as high-quality LED drivers, advanced dimming methods, and digital control systems are explored. Our findings show these techniques can significantly reduce flicker, achieving less than 1% flicker performance while meeting HCL’s diverse requirements. Implementing flicker-free lighting in residential spaces enhances comfort and reduces eye strain, while in industrial settings, it improves productivity and safety. This paper emphasizes the importance of control circuits that maintain sub-1% flicker performance while integrating various HCL solutions, enhancing indoor lighting quality, and promoting better health and performance.

In order to widely disseminate LED lighting, LED lighting technology that directly uses AC commercial power has been recently introduced. AC powered LED lighting technology has a problem in that the light brightness of the LED changes because the voltage applied to the LED and the current flowing through the LED continuously change. In this study, when the LED current is greater than the design current, the current control signal generated by the controller is supplied to the current source to supply only the design current to the LED by increasing the voltage drop at the current source. If it is smaller than the design current, the controller is adjusted so that the current is supplied only to the LED without a voltage drop in the current source. It can be seen that the higher the maximum rectified voltage, the faster the lighting time of the LED light emitting block is, so that the power factor of the LED lighting is improved. The LED lighting technology proposed in this study enables LED lighting with constant light brightness, reduced power consumption, and long lifetime.

This study tested the electrical, structural, and thermal safety of LED lighting products, available on the market. Five recessed LED systems, 20 W each, and five fixed LED systems, 25 W each, were selected. Dielectric strength tests, live part electric shock protection tests, and thermal tests were conducted on the LEDs. These were key tests for user safety, according to the specification of the safety criteria for electric products, KC 60598-1, South Korea. In addition, the wiring temperature of UL1007, 60227 IEC 08, and UTP cables, was measured. The results of the study gave an in-depth examination of the safety of LED lighting systems for users.

This is the study on the development of fusion heat dissipation of carbon magnesium materials. The purpose of this study is for effective utilization of heat emission which is the core of LED lighting. The result of study enabled the derivation of side satisfying result of making the surface temperature of lighting to be below 70℃ (actual measurement: 58℃) using magnesium. The lighting products that use magnesium was made possible based on the result of this study. Also from the performance aspect such as light distribution, the measurement of light efficiency demonstrated the level of 90 lm/W. Therefore the commercialization of lighting was made possible and the efficiency could be further enhanced by supplementation of LED performance.

The rectified voltage supplied to LED lamp is used in load and then the surplus voltage can be produced in LED lighting. In this case, LED lighting is proposed that can recyclable the excess voltage to supply power to the controller.

LED is divided to multichannel in order not to exceed a certain voltage in aspects of electric standard. However, it`s not possible to know in accordance with what channel SMPS controls the constant voltage and current. In order to solve this problem, it needs to detect the maximum LED String voltage which is applied to LED control circuit, and it is possible to minimize the voltage drop when a difference of LED string voltage occurs by each channel if LED is controlled by the maximum LED string voltage detected. In addition, it is also possible to maximize the efficiency of LED if change LED voltage by detecting the maximum voltage. Feasibility of this claim was verified through implementation of the circuit.