Oxide semiconductor gas sensors are widely used for detecting toxic, explosive, and flammable gases due to their simple structure, cost-effectiveness, and potential integration into compact devices. However, their reliable gas detection is hindered by a longstanding issue known as humidity dependence, wherein the sensor resistance and gas response change significantly in the presence of moisture. This problem has persisted since the inception of oxide semiconductor gas sensors in the 1960s. This paper explores the root causes of humidity dependence in oxide semiconductor gas sensors and presents strategies to address this challenge. Mitigation strategies include functionalizing the gas-sensing material with noble metal/transition metal oxides and rare-earth/rare-earth oxides, as well as implementing a moisture barrier layer to prevent moisture diffusion into the gas-sensing film. Developing oxide semiconductor gas sensors immune to humidity dependence is expected to yield substantial socioeconomic benefits by enabling medical diagnosis, food quality assessment, environmental monitoring, and sensor network establishment.

For the purpose of treating health checkups and recovery of patients in a super-aged society, hospitals use devices designed with a reduction circuit of electromagnetic waves associated with the specific absorption rate of electromagnetic waves absorbed by the human body. In this paper, we proposed a filter improvement design method capable of reducing electromagnetic waves. As a result of confirming the validity of the proposed technique through simulation and experimental results, the following result values were obtained. Applying the common-mode (CM) inductor 4 mH to a calibration circuit, noise decreased in a multiband spectrum. Using the differential mode(DM) inductor 40 μH element in the primary calibration circuit, the noise decreased by 15 dB or more in the 3 MHz band spectrum. Also, applying the Admittance Capacitance (Y-Cap) 10 nF element in the secondary calibration circuit resulted in the decrease by more than 30 dB in the band spectrum before 2 MHz. After using a common-mode inductor 4 mH element in the tertiary calibration circuit, it decreased by more than 15 dB in the band spectrum after 2 MHz.

As a ZnO varistor is subjected to electrical and environmental stresses, it degrades gradually, which may result in power interruption by short circuit. This study investigates changes in the electrical characteristics of ZnO varistors due to deterioration owing to energy absorption, and determines the optimal parameters for on-line diagnosis of the varistor. Two types of varistors were used for an accelerated aging experiment involving the application of the 8/20 μs standard lightning impulse current. The electrical characteristics in terms of the reference voltage, total leakage current, resistive leakage current, and third-harmonic component of the total leakage current were measured, and their change rates were analyzed. The results revealed that the total leakage current increased slightly with an increase in the varistor absorbed energy, while the resistive leakage current and the third-harmonic component increased apparently. Therefore, the third-harmonic component of the total leakage current was proposed as the optimal parameter for on-line monitoring of ZnO varistor conditions.

The white light of a hybrid LED is obtained by using red and green organic fluorescent layers made of polymethylmethacrylate (PMMA) films, which function as color down-conversion layers of blue light-emitting diodes. In this research, we studied the fluorescence properties of a red organic fluorophore, employing perylene bisimide derivatives applicable to hybrid LEDs. The solubility, thermal stability, and luminous efficiency are important characteristics of organic fluorophores for use in hybrid LEDs. The perylene fluorescent compounds (1A and 1B) were prepared by the reaction of 4-bromophenol and 4-iodophenol with N,N`-bis(4-bromo-2,6-diisopropylphenyl)-1, 6,7,12-tetrachloroperylene-3,4,9,10-tetracarboxyl diimide (1) in the presence of dimethyl formaldehyde (DMF) at 70℃. The synthesized derivatives were characterized by using 1H-NMR, FT-IR, UV/Vis absorption and PL spectra, and TGA analysis. Compounds 1A and 1B showed absorption and emission at 570 nm and 604 nm in the UV/Vis spectrum. We also documented favorable solubility and thermal stability characteristics of the perylene fluorophores in our work. Perylene fluorophore 1, with the 4-bromophenol substituent 1A, exhibited particularly good thermal stability and solubility in organic solvents.

In the present study, the CuNx-Cu-CuNx layer the partial pressure ratio Cu metal of Ar and N2 gas using a DC magnetron sputtering device, was generated by the In-situ method. CuNx layer was able to obtain a surface reflectance reduction effect from the advantages of the process and the external light. CuNx layer is gas partial pressure, DC the Power, the deposition time variable transmittance in response to the thickness and partial pressure ratio, the reflectance was measured. Ar:N2 gas ratio 10:10(sccm), DC power 0.35 A, was derived Deposition time 90 sec optimum conditions. Thus, according to the optimal thickness and the composition ratio was derived surface reflectance of 20.75%. In addition, to derive the value of △ Ra surface roughness of 0.467. It was derived CuNx band-gap energy of about 2.2 eV. Thus, to ensure a thickness and process conditions can be absorbed to maximize the light in a wavelength band in the visible light region. As a result, the implementation of the 1.2 ㏀ base line resistance of using the Cu metal. This is, 5 inch Metal mesh TSP(L/S: 4/270 ㎛) is in the range of the reference operation.

Transparent UV photodetector was achieved by using wide bandgap metal oxide materials. In order to realize transparent heterojunction UV photodetector, n-type ZnO and p-type NiO metal oxide materials were employed. High light-absorbing SnS layer was inserted into the n-ZnO and p-NiO layers. High-performing UV photodetector was realized by ZnO/SnS/NiO/ITO structures to provide extremely fast response times (Fall time: 7 μ s and rise time: 13 μs) and high rectifying ratio. The use of functional SnS-embedded photodetector would provide a route for high functional photoelectric devices.

In this paper, the efficiency improvement of the heterojunction with intrinsic thin layer (HIT) solar cells is obtained by optimization process of p-type a-SiC:H as emitter. The optoelectronic of p-type a-SiC:H layers including the optical band-gap and conductivity under the methane gas content variation is conducted in detail. A significant increase in the Jsc by 1 mA/cm2 and Voc by 30 mV are attributed to enhanced photon-absorption due to broader band-gap of p-a-SiC:H and reduced band-offsets at p-side interface, respectively of HIT solar cells.

In this research, we focused on the improvement of cy3 dye’s characteristics for LCD color filter. Solubility and thermal stability are main characteristics of dyes for LCD color filter. We performed experiment to change counter cation of cy3 dyes with alkoxy substituent for these purposes. These cy3 dyes (1b∼5b) were prepared through the synthetic procedure of three steps. The synthesized new cy3 dyes were charaterized by using NMR, FT-IR, UV/Vis spectroscopy, and TGA. These cy3 dyes showed purple color and maximum absorption wavelength (λmax) in the range of 578∼590 nm in UV/Vis spectrum. We confirmed that solubility and thermal stability of cy3 dyes were dependent on the structure of counter cation. Cy3 dyes with alkoxy substituent have good solubility in organic solvents such as dichloromethane, methanol, and acetone. Especially, Cy3 dye with 4-nitrobenzyl counter cation (5b) gave excellent solubility characteristics.

In this research, we focused on the development of cy3 dye with high thermal stability and good solubility for LCD color filter. Cy3 dyes were prepared through the synthetic procedure of two steps. The synthesized cy3 dyes were characterized by using NMR, FT-IR, UV/Vis spectroscopy, and TGA. These cy3 dyes showed maximum absorption wave length (λmax) in the range of 549∼555 nm in UV/Vis spectrum. And we confirmed that solubility characteristics and thermal stability of cy3 dyes were dependent on the structure of counter cation. Cy3 dyes with methyl counter cation and ethyl counter cation have good solubility in organic solvents such as chloroform, ethanol, and PGME. Moreover, Cy3 dye with ethyl counter cation gave excellent thermal stability in TGA thermograms. And Cy3 dye with ethyl counter cation showed good result in photoresist film test.

TiNOx multi-layer thin films on aluminum substrates were prepared by DC reactive magnetron sputtering method. 4 multi-layers of TiO2/TiNOx(LMVF)/TiNOx(HMVF)/Ti/substrate have been prepared with ratio of Ar and (N2+O2) gas mixture. TiO2 of top layer is anti-reflection layer on double TiNOx(LMVF)/TiNOx(HMVF) layers and Ti metal of infrared reflection layer. In this study, thecrystallinity and surface properties of TiNOx thin films were estimated by X-ray diffraction(XRD) and field emission scanning electron microscopy(FE-SEM), respectively. The grain size of TiNOx thin films shows to increase with increasing sputtering power. The composition of thin films has been investigated using electron probe microanalysis(EPMA). The optical properties with wavelength spectrum were recorded by UV-Vis-NIR spectrophotometry at a range of 200∼1,500 nm. The TiNOx multi-layer films show the excellent optical performance beyond 9% of reflectance in those ranges wavelength.

AlNO multi-layer thin films on aluminum substrates were prepared by DC reactive magnetron sputtering method. Al2O3/AlNO(LMVF)/AlNO(HMVF)/Al/substrate of 4 multi-layer has been prepared in an Ar and (N2+O2) gas mixture, and Al2O3 of top layer is anti-reflection layer on double AlNO(LMVF)/AlNO(HMVF) layers and Al metal of infrared reflection layer. In this study, the roughness and surface properties of AlNO thin films were estimated by field emission scanning electron microscopy(FE-SEM). The grain size of AlNO thin films increased with increasing sputtering power. The composition of thin films has been systematically investigated using electron probe microanalysis(EPMA). The optical properties with wavelength spectrum were recorded by UV-Vis-NIR spectrophotometry at arange of 200～1,500 nm. The absorptance of AlNO films shows the increasing trend with swelling(N2+O2) gas mixture in HMVF and LMVF deposition. The excellent optical performance showed above98% of absorptance in visible wavelength region.

In this paper, we studied the magnetic composite sheets for electromagnetic wave noise absorber of quasi-microwave band by using soft magnetic FeSiCr and Fe50Ni flakes with the thickness of about 1 μm and polymer. The magnetic hysteresis curve including saturation magnetization and residual magnetization and the complex permeability characteristics of the composite sheets were investigated to clarify the mixing effect on electromagnetic wave absorption properties. The saturation magnetization was decreased about 10% while the residual magnetization was increased about 15% and the real parts of complex permeability at below 500 MHz were increased 0.6～4 while those values at above 500 MHz were decreased 0.4～2.5 according to the change of contents of FeSiCr and Fe50Nipowders. As a result, the reflection loss can be moved to the lower frequency from 2∼3 GHz to 1∼1.5GHz as the contents of Fe50Ni flaky powder into FeSiCr flaky powder was increased up to 50%.

In this paper, we prepared Cu(In,Ga)Se2 thin films by using co-evaporation method, and analyzed the properties of the thin films. During the thin film preparation process, we confirmed InGaSe2 phase was formed at 400℃ in first stage, and also confirmed the thin films showed the vacancy decrease. In second and third stage,we confirmed the density increase of crystalline structure at over 480℃ and the formation of Cu(In0.7Ga0.3)Se2phase. As the result of SEM and XRD analysis of the films which were before and after heat-treated, we confirmed the disappearance of Cu2Se2 and the formation of Cu(In0.7Ga0.3)Se2 single phase after the heat-treatment,We, therefore, confirmed the heat-treatment did not affect the absorbency spectra of the thin films.

Magnetoelectric(ME) bulk composites with PZT- PYN- PZN/FeO1 were prepared by using a conventional ceramic methods and investigated on the ME voltage vs frequency of ac magnetic fields. We made the electric equivalent circuits by using the Maxwell-Wagner model and simulated the frequency dependence of ME voltage in low frequency region. IVIE devices were described by a series of two equivalent circuits of piezoelectric and magnetic, which have the relaxation time T due to the interaction between ME device and load resistor. Equivalent circuit of piezoelectric material is independent of frequency. However ferrite magnetic materials have Debye absorption and dipolar dispersion, whose equivalent circuit is a function of frequency. Therefore we suggest the resistance in the equivalent circuit is proportion to (1 + w2t2) and the capacitance is in inverse proportion to (1 + w w2t2) in the magnetic materials.

An optical model is proposed in the white LED using phosphor and LED chip. In this paper a new model that describes the absorption rate and quantum efficiency with increasing the mixing ratio of phosphor in silicone, and the allotment of the phosphor absorption optical power in the several phosphor mixing in the silicone. Single phosphor in silicone from the optical measurement data before and after molding, the solution to get the blue optical power and the phosphor emission optical power is proposed. By these solution the absorption rate and the quantum efficiency was obtained. The model with single phosphor mixing in the silicone the validity was confirmed.

We present the results of a study of the polarizing photovoltaic (PV) effects in an aligned polymer bulk heterojuction PV layer. The fairly uniform in-plane uniaxial alignment of the PV layer with a macroscopic axial orientational order parameter of 0.40 was achieved by means of a simple rubbing technique. Moreover, reflective polarizing PSCs having the aligned PV layers were applied to power-generating reflective type liquid crystal displays (LCDs), which exhibited a maximum contrast ratio of 1.7. These results form a promising foundation for various energy harvesting polarization dependent opto-electrical LCD device applications.

Porous carbon electrodes with wooden materials are manufactured by molding carbonized wood powder. Electrical properties of the interface for electrolyte and porous carbon electrode are investigated from viewpoint of NaCl electrolyte concentration, capacitance and complex impedance. Density of porous carbon materials is 0.47∼0.61 g/cm3. NaCl electrolytic absorptance of the porous carbon materials is 5∼ 30%. As the electrolyte concentration increased, capacitance is increased and electric resistance is decrease with electric double layer effect of the interface. The electric current of the porous carbon electrode compared in the copper and the high density carbon electrode was improved on a large scale, due to a increase in surface area. The circuit current increased as the distance between of the porous carbon electrode and the zinc electrode decreased, due to increase in electric field. Experimental results indicated that the current properties of galvanic cell could be improved by using porous carbon electrode.