Ni germanide (NiGe) is a promising alloy material with small contact resistance at the source/drain (S/D) of Ge MOSFETs. However, it is necessary to reduce the specific contact resistance between NiGe and the doped Ge S/D region in high-performance MOSFETs. In this study, a novel method is proposed to reduce the specific contact resistance between NiGe and p-type Ge (p-Ge) using a Tb interlayer. The specific contact resistance between NiGe and p-Ge was successfully decreased with the introduction of the Tb interlayer. To investigate the mechanism behind the reduction in the specific contact resistance, the elemental distribution and crystalline structure of NiGe were analyzed using secondary ion mass spectroscopy and X-ray diffraction. It is likely that the reduction in specific contact resistance was caused by an increase in the concentration of boron in the space between NiGe and p-Ge due to the influence of the Tb interlayer.

In this study, the effect of Tb inward diffusion on the magnetic properties of the Nd-Fe-B sintered magnets was studied. After sintering of the magnets, TbF₃ slurries were dip-coated on the surface of the samples, then heat-treatment was followed for TbF₃ diffusion. The element distribution in the magnets and the diffusion profiles of Tb ions were analyzed by an EPMA (electron probe micro-analyzer). Prolonged heat treatment resulted in a deeper diffusion length of Tb ions. Coercivity of the 1^st heat-treated sample showed 21.86 kOe, while that of the 1^st, 2^nd heat-treated and annealed sample revealed 34 kOe.

Among the various physiological information that could be obtained from human body, heartbeat rate is a commonly used vital sign in the clinical milieu. Photoplethysography (PPG) sensor is incorporated into many wearable healthcare devices because of its advantages such as simplicity of hardware structure and low-cost. However, healthcare device employing PPG sensor has been issued in susceptibility of light and motion artifact. In this paper, to develop the real-time heart rate measurement device that is less sensitive to the external noises, we have fabricated an ultra-small wireless LC resonant pressure sensor by MEMS process. After performance evaluation in linearity and repeatability of the MEMS pressure sensor, heartbeat waveform and rate on radial artery were obtained by using resonant frequency-pressure conversion method. The measured data using the proposed heartbeat rate measurement system was validated by comparing it with the data of an commercialized heart rate measurement device. Result of the proposed device was agreed well to that of the commercialized device. The obtained real time heartbeat wave and rate were displayed on personal mobile system by bluetooth communication.

This paper tried to develop a BLDC electric motor securing the 800 W-level watertight structure for driving the outboard motor. For this purpose, this paper developed a high-efficient controller-integrating BLDC electric motor system for underwater propulsion and designed and developed a triple watertight structure. Besides, this study developed a outboard motor integrating motor, propeller and controller based on the production of a controller for BLDC motor which can the speed control by selecting low-voltage, high-current power element. The characteristics of developed outboard motor were 24 V input voltage, over 800 W motor output, and max. 3,000 rpm motor, and 84.9% motor efficiency,and the developed outboard motor could secure the watertight structure in 5 m in water depth.

CaMoO4:Tb3+ green phosphor powders and thin films were successfully prepared by using the solid-state reaction method and the radio-frequency magnetron sputtering technique, respectively. The crystalline structure of all phosphor powders with different Tb3+ ion concentrations was found to be a tetragonal system with the maximum diffraction intensity at 28.58°, while that of the phosphor thin films, irrespective of the type of substrate, was amorphous. As for the phosphor powders, the grain particles showed the chain-like patterns with inhomogeneous size distribution, the excitation spectra were composed of a broad band peaked at 307 nm and two small narrow bands centered at 381 and 492 nm, and the highest green emission spectrum was observed at 0.01 mol of Tb3+ ions. As for the phosphor thin films, the average transmittance exceeding 85% was measured in the 400∼1,100 nm range and the optical band gap showed a significant dependence on the type of substrate.

TBP (tertiarybutylphosphine), a relatively new material for phosphorus, has been studied with EDMIn (ethyldimethylindium) as an indium source for the growth of InP by MOVPE (metalorganic vapor phase epitaxy). Mirror smooth and good crystalline InP layers were obtained at 500-600℃ with the TBP/EDMIn molar ratio as low as 21. The deposited InP layers are all n-type with the electron concentration in the range of (5-10)×10(16) cm-3, which is a lot higher than those from PH3. This high concentration is due presumably to the high concentration of donor impurities in TBP. And it has been found that the formation of adduct occurs between EDMIn and TBP at room temperature when the partial pressure of EDMIn in the reactant mixture is above 1×10(-2) Torr. The high concentration of impurities in TBP and the adduct formation between EDMIn and TBP are major obstacles in replacing PH3 and TMIn for the growth of device quality InP layers.

Y1-xBO3:Tbx 3+ ceramic phosphors were synthesized with changing the concentration of Tb3+ at a sintering temperature of 1,100℃ and a reduction temperature of 950℃ by using a solid-state reaction method. The crystal structure, surface morphology, and photoluminescence properties of the phosphors were investigated as a function of Tb3+ ion concentration by using XRD (x-ray diffractometer), scanning electron microscopy, and photoluminescence spectrophotometry, respectively. The XRD results showed that the main peak of the phosphor powders occurs at (101) plane. As for the photoluminescence properties, the excitation spectra showed the broad band centered at 306 nm and the emission intensity of the spectra peaked at 543 nm indicated a significant decrease as the concentration of Tb3+ ion is increased.