The direct utilization of steelmaking by-product gases in solid oxide fuel cells (SOFCs) offers a promising pathway to improve energy efficiency and reduce carbon emissions in the steel industry. In this study, a Sr-deficient and Ni-doped double perovskite oxide, Sr_1.95Fe_1.35Ni_0.15Mo_0.5O_6-δ (SFNM), was investigated as an anode material for direct Linz-Donawitz converter gas (LDG)-fueled SOFCs. A single-phase double perovskite structure was successfully obtained after calcination at 1,200°C for 12 h, while exsolved metallic Ni nanoparticles were generated on the SFNM surface after reduction at 800°C. Electrochemical performance was evaluated using H₂, simulated-LDG, and CO/CO₂ (85:15) fuels at 800°C. The maximum power densities achieved were 1.23, 0.70, and 0.40 W cm^-2 for H₂, simulated-LDG, and CO/CO₂ fuels, respectively. Although CO-containing fuels exhibited lower opencircuit voltages and power outputs than H₂, the SFNM anode maintained stable operation and appreciable performance under direct simulated-LDG utilization. Impedance analysis revealed that the increased polarization resistance in simulated-LDG and CO/CO₂ atmospheres was mainly associated with fuel adsorption/desorption and gas diffusion, while interfacial charge-transfer resistance remained relatively small. The superior performance obtained with simulated-LDG compared to the CO/CO₂ mixture was attributed to the presence of a small amount of H₂, which facilitated anode reaction kinetics. These results demonstrate that SFNM is a promising mixed ionic-electronic conductor anode for the direct electrochemical conversion of CO-rich steelmaking by-product gases into electricity.

As the recent climate problems are getting worse year after year, the demands for clean energy materials have highly increased in modern society. However, the candidate material classes for clean energy expand rapidly and the outcomes are too complex to be interpreted at laboratory scale (e.g., multicomponent materials). In order to overcome these issues, the firstprinciples calculations are becoming attractive in the field of material science. The calculations can be performed rapidly using virtual environments without physical limitations in a vast candidate pool, and theory can address the origin of activity through the calculations of electronic structure of materials, even if the structure of material is too complex. Therefore, in terms of the latest trends, we report academic progress related to the first-principles calculations for design of efficient electrocatalysts. The basic background for theory and specific research examples are reported together with the perspective on the design of novel materials using first-principles calculations.

To overcome the limitations of the conventional Ni anode-supported SOFCs, various types of ceramic anodes have been studied. However, these ceramic anodes are difficult to commercialize because of their low cell performances and difficulty in manufacturing anode-support typed SOFCs. Therefore, in this study, to use these ceramic anodes and take advantage of anode-supported SOFC, which can minimize ohmic loss from the thin electrolyte, we fabricated cathode support-typed SOFC. The cathode-support of LSCF-YSZ was prepared by the acid treatment of conventional Ni-YSZ (Yttria-stabilized Zirconia) anode-support, followed by the infiltration of LSCF to YSZ scaffold. The composite of La(Sr)Ti(Ni)O₃ and Ce(Mn, Fe)O₂ was used as the ceramic anode. The fabricated cathode-supported button cell showed a relatively low power density of 0.207 Wcm^-2 at 850℃; however, it is expected to show better performance through the optimization of the infiltration rate and thickness of LSCF-YSZ cathode-support layer.

Single-chamber solid oxide fuel cells (SC-SOFCs) consist of only one gas chamber, in which both the anode and the cathode are exposed to the same fuel-oxidant mixture. Thus, this configuration shows good thermal and mechanical resistance and allows rapid start-up and -down. In this study, the unit cell consisting of La_0.8Sr_0.2MnO₃ (cathode) / Zr_0.84Y_0.16O_2-x (electrolyte) / Ni-Zr_0.84Y _0.16O_2-x (anode) was fabricated and its electrochemical property was investigated as a function of temperature and the volume ratio of fuel and oxidant for SC-SOFCs. Impedance spectra were also investigated in order to figure out the electrical characteristics of the cell. As a result, the cell performance was governed by the polarization resistances of the electrodes. The cell exhibited an acceptable cell-performance of 86 mW/cm2 at 800℃ and stable performance for 3 hs under 0.7 V.

In this paper existing buildings, not a new buildings and house for living people not just a displaying and a viewing, created by the imagine effect or virtual simulation was applied various Active and Passive elements. After constructing zero-energy houses, through default case happened during operation period it is described problems and solutions about field part, work classification, installation by Location part, and Installation equipment part. Since then, to take advantage of this thesis, it``s the purpose of this paper using as the baseline data for building a zero-energy house in another similar case.

In solid oxide fuel cell system, yttria-stabilized zirconia is generally adopted as the electrolyte, which has high strength and superior oxygen ion conductivity, and the air electrode and the fuel electrode are attached to this. Recently, new structure of ``layered planar SOFC module`` was suggested to solve there liability problem due to the high temperature stability of a sealing agent and a binding material. In this study to materialize the air electrode in a layered planar SOFC module, the LSM ink was coated to form homogeneous electrode in the channel after the ink preparation. As the porosity control agent, PMMA oractive carbon powder was adopted with use of a commercial dispersant in ethanol. The optimal amounts of both the porosity control agents and the dispersant were determined. Four (4) vol% of the dispersant for the LSM-PMMA case and 15 vol% for LSM-carbon powder showed the lowest viscosities respectively to indicate the best dispersed states of the slurries. With PMMA and carbon powder, sintered LSM ink shows the relatively homogeneous distributions of pores and with increases of the agents, the porosities increased in both cases. From this, it can be thought that the amount of the PMMA or carbon powder could be used to control the porosity of the LSM ink.

The properties of green sheet were investigated in order to understanding an effects of organic solvent mixture ratio for solid oxide fuel cells fabrication, The purpose of this work is to optimize the slurry condition using the design of experiment to improve green sheet properties. The elongation increased with increasing amount of binder and solvent. With increasing amount of solvent, the air permeability increased but the tensile strength decreased. The best properties of the green sheet appeared amount of the binder 17 wt%, solvent 35 wt% and powder 48 wt%. The optimum condition of green and sintered density for solid oxide fuel cells fabrication was obtained in the sample pressured at 800kgf/㎠.