The overhead contact line (OCL) is a key piece of equipment for transmitting electrical energy to the pantograph of rail cars. Recently, a 400 km/h OCL was applied to the Honam high-speed line, and its performance was examined by running HEMU-430X. For the study, we analyzed the current of catenary wire concurrently while running HEMU-430X in the Honam high-speed line. Specifically, this study recorded the currents for each speed during operation of the railway vehicle. The analysis of the frequency of line current showed generation of third-harmonics, 15th-harmonics, 17th-harmonics, and 19th-harmonics. The current of catenary wire is a basic technology assessment used to determine the electrical safety of electric railway systems, and it can be used as a technology for analyzing circulating currents generated in the current configuration, as well as for analyzing electric fatigue of the OCL components.

Bonding properties of epoxy-containing solder joints were investigated by a high temperature aging test. Specimens were prepared by bonding an R3216 standard chip resistor to an OSP-finished PCB by a reflow process with two basic types of solder (SAC305 & Sn58Bi) pastes and two epoxy-solder (SAC305+epoxy & Sn58Bi+epoxy) pastes. In all epoxy solder joints, an epoxy fillet was formed in the hardened epoxy, lying around the outer edge of the solder joint, between the chip and the Cu pad. In order to analyze the bonding characteristics of solder joints at high temperatures, a high-temperature aging test at 150°C was carried out for 14 days (336 h). After aging, the intermetallic compound Cu₆Sn₅ was found to have formed in the solder joint on the Cu pad, and the shear stress on the conventional solder joint was reduced by a significant amount. The reason that the shear force did not decrease much, even though in epoxy solder, was thatbecause epoxy hardened at the outer edge of the supported solder joints. Using epoxy solder, strong bonding behavior can be ensured due to this resistance to shear force，even in metallurgical changes such as those where intermetallic compounds form at solder joints.

This paper proposes an easy algorithm for finding tapped-delay-line (TDL) filter coefficients in an adaptive filter algorithm using orthogonal input signals. The proposed algorithm can be used to obtain the coefficients and errors of a TDL filter without using an inverse orthogonalization process for the orthogonal input signals. The form of the proposed algorithm in this paper has the advantages of being easy to use and similar to the familiar recursive least-squares (RLS) algorithm. In order to evaluate the proposed algorithm, system identification simulation of the 11^th-order finite-impulse-response (FIR) filter was performed. It is shown that the convergence characteristics of the learning curve and the tracking ability of the coefficient vectors are similar to those of the conventional RLS analysis. Also, the derived equations and computer simulation results ensure that the proposed algorithm can be used in a similar manner to the Levinson-Durbin algorithm.

Ferroelectric material properties are strongly governed by domain structures and their evolution processes, but the evolution processes of complex domain patterns during a macroscopic electrical poling process are still elusive. In the present work, domain-evolution processes in a PZT ceramic near the morphotropic phase-boundary composition were studied during a step-wise electrical poling using piezoresponse force microscopy (PFM). Electron backscatter diffraction was used with the PFM data to identify the grain boundaries in the region of interest. In response to an externally the applied electric field, growth and retreat of non-180° domain boundaries wasere observed. The results indicate that ferroelectric polarization-switching nucleates and evolves in concordance with the pattern of the pre-existing domains.

Various process technologies for manufacturing power inductors are under development. The core goal is to increase the mixing ratio of the soft magnetic powder in the epoxy, and to uniformly disperse it in a molding-type power inductor, manufactured by the injection molding method. In this study, we investigated the effect of dispersant and silane on the dispersion of soft magnetic metal powders in epoxy. We added 0.6 wt% of dispersant and 2.0 wt% of silane, and an excellent dispersibility resulted. Under the conditions of 0.3 wt% of dispersant and 0.5 wt% of silane, we added both dispersant and silane together to observe the effect of their interaction on dispersibility. Similarly, the addition of 0.3 wt% of dispersant and 0.1 wt% of silane resulted in a sharp increase in viscosity, considered to be due to the interaction of the dispersant and silane. The addition of 0.1 wt% of dispersant with 0.5 wt% of silane resulted in a sharp rise in viscosity, and sedimentation-height decreased sharply due to the dispersion optimization.

A newly proposed T-shape piezoelectric actuator, composed of piezoelectric benders, was designed and studied. This actuator has four legs, and can walk in both forward and backward directions. The piezoelectric actuator has a simple structure and can be easily fabricated. It consists of a piezoelectric bender and a joint. The piezoelectric bender is composed of carbon and ceramic materials. Therefore, there is an advantage in that it can be fabricated on a very small scale. Elliptical displacements of the piezoelectric actuators were analyzed by finite element analysis. Elliptical motion at the tip occurred at two voltages having a 90-degree phase difference. Based on the finite element analysis results, prototype actuators with maximum displacements were fabricated, and the characteristics of their movements were characterized.

In this study, we investigated the optimum calcination temperature of lead-free 0.74(Bi_0.5Na_0.5)TiO₃-0.26SrTiO₃ (BNST) piezoelectric ceramics by analyzing the crystal structure, dielectric properties, and electric field-induced strain behavior. BNST ceramics prepared by conventional solid-state reaction methods at various calcination temperatures according to the industrial standard. All samples of BNST ceramics were subsequently sintered at 1,175℃ for 2 h. Crystal structure classification of the ceramics showed a single perovskite phase, with no second phase detectable for the samples calcined at 750℃ or higher. BNST samples calcined at 850℃ exhibited the most optimal values for itsand the common physical parameters of density = 5.518 g/㎤, ε = 1,871.837, tanδ = 0.047, and d₃₃^* = 874 pm/V.

To study the frequency response characteristics of alternating-current-driven organic light-emitting diodes (OLEDs), we fabricated blue-fluorescent OLEDs and analyzed their electroluminescent characteristics according to the alternating current voltage and frequency. The luminance-frequency characteristics of alternating-current-driven OLED was similar to that of a low-pass filter，and the luminance of high-voltage OLED decreased at higher frequency than low-voltage OLED. The luminance characteristics of the OLED according to the frequency is due to the capacitive reactance in the OLED, generated during the alternating current driving. The frequency response characteristics of the OLED according to the voltage is due to the decrease in internal resistance of the organic layer. In addition, the negative voltage component of the alternating current did not affect the frequency response of the OLED. Therefore, the electroluminescent characteristics of OLED with an alternating current power of 60 Hz are not influenced by the frequency.

Micro-LEDs show lower efficiencies compared to general LEDs having large areas. Simulations were carried out using ray-tracing software to investigate the change in light extraction efficiency and light distribution according to chip-size of blue flip-chip micro-LEDs (FC μ-LEDs). After fixing the height of the square FC μ-LED chip at 158 μm, the length of one side was varied, with dimensions of 2, 5, 10, 30, 50, 100, 300, and 500 μm. The highest light-extraction efficiency was obtained at 10 μm, beyond which the efficiency decreased as the chip-size increased. The chip size-dependence of the FC μ-LEDs both without the patterned sapphire substrate, as well as vertical FC μ-LEDs, were analyzed.

Recently, the application field of solar panels is increasing. Accordingly, the demand for flexible devices is also steadily increasing. It is therefore necessary to develop TiO₂ paste for low-temperature annealing for flexible DSSC fabrication. In this study, the TiO₂ paste for low-temperature annealing with varying molar ratio of titanium isopropoxide (TTIP) was prepared, and DSSC was fabricated and its characteristics were compared. As a result, there was no deformation of the particles on the surface in the SEM data. However, the highest open circuit voltage, short circuit current, and fill factor were measured in the DSSC unit cell prepared by adding 0.5 mol of TTIP to the TiO₂ paste, and the highest efficiency was 4.148%.

Lithium-ion batteries used for IT, automobiles, and industrial energy-storage devices have battery management systems (BMS) to protect the battery from abnormal voltage, current, and temperature environments, as well as safety devices like, current interruption device (CID), fuse, and vent to obtain positive temperature coefficient (PTC). Nonetheless, there are harmful to human health and property and damage the brand image of the manufacturer because of smoke, fire, and explosion of lithium battery packs. In this paper, we propose a systematic protection algorithm combining battery temperature, over-current, and interconnection between protection elements to prevent copper deposition, internal short circuit, and separator shrinkage due to frequent and instantaneous over-current discharges. The parameters of the proposed algorithm are suggested to utilize the experimental data in consideration of battery pack operating conditions and malicious conditions.

Methylammonium lead triiodide (MAPbI₃)-based perovskite solar cells potentially have potential advantages such as high efficiency and low-cost manufacturing procedures. However, MAPbI₃ is structurally unstable and has low phase-change temperatures (30°C and 130°C); it is necessary to solve these problems. We investigated the crystal structure and phase separation using real-time temperature-change X-ray diffraction, transmission electron microscopy, and electron energy loss spectroscopy. MAPbI₃ has a tetragonal structure, and at about 35°C the c-axis contracts, transforming MAPbI₃ into the related cubic crystal structure. In addition, at 130°C, phase separation occurs in which CH₃NH₂ and HI at the center of the unit cell of the perovskite structure are extracted by gas, leavingand only PbI₂ of the three-component structure, is produced as the final solid product.

SiO_x nanoparticles were granulated, and their microstructures and effects on electrochemical behaviors were investigated. In spite of the promising electrochemical performance of SiO_x, nanoparticles have limitations such as high surface area, low density, and difficulty in handling during slurry processing. Granulation can be one solution. In this study, pelletizing and annealing were conducted to create particles with sizes of several decades of micron. Decrease in surface area directly influences the initial charge and discharge process when granules are applied as anode materials for Li-ion batteries. Lower surface area is key to decreasing the amount of irreversible phase-formation, such as Li₂Si₂O₅, Li₂SiO₃ and LuSiO₄, as well as forming the solid electrolyte interface. Additionally, aggregation of nanoparticles is required to obtain further enhancement of the electrochemical behavior due to restrictions that there be no Li₄SiO₄-related reaction during the first discharge process.

The effect of various lithium sources such as LiCl, LiOH, and Li-metal on the microstructure and electrochemical properties of granulated SiO_x powders were investigated. Various lithium sources were metallurgically added for a passive pre-lithiation of SiO_x to improve its low initial coulombic efficiency. In spite of using the same amount of Li in various sources, as well as the same process conditions, different lithium silicates were obtained. Moreover, irreversible phases were formed without reduction of SiO_x, which might be from additional oxygen incorporation during the process. Accordingly, there were no noticeable electrochemical enhancements. Nevertheless, the Li₄SiO₄ phase changes the initial electrochemical reaction, and consequently the relationship between the microstructure and electrochemical properties of metallurgically pre-lithiated SiO_x could provide a guideline for the optimization of the performance of lithium ion batteries.

Although perylene bisimide derivatives have advantages such as excellent thermal stability and high luminance efficiency, they have poor solubility characteristics in organic solvents. In this research, in order to improve the solubility characteristics, we prepared perylene bisimide derivatives (1C) and (2C) with swallow-tail substituted imide, which is known to lead to excellent solubility. The structures and properties of swallow-tail perylene bisimide (1C) and (2C) were analyzed by ¹H-NMR, FT-IR, UV/Vis spectroscopy, and thermogravimetric analysis (TGA). The maximum absorption wavelengths of (1C) and (2C) in the UV/Vis spectrum were 558 nm and 556 nm, respectively, and the maximum emission wavelengths were 602 nm and 600 nm, respectively. In the TGA, (1C) demonstrated good thermal stability with less than 5 wt% weight loss up to 242℃. In the solubility test, (1C) and (2C) exhibited solubilities of more than 5 wt% in chloroform, ethyl acetate, and dimethylformamide, but not in methanol. When the compounds (1C) and (2C) were mixed with PMMA (polymethyl methacrylate), thin films showed peaks at 679 nm and 677 nm, respectively, in the photoluminescence spectra. (1C) was found to be a possible candidate as red organic phosphor for hybrid LEDs.